Search found 11 matches

by dirk_k
04 Jul 2018, 22:17
Forum: ESP Easy: Software
Topic: MQTT Import - stability problems ...?
Replies: 12
Views: 678

Re: MQTT Import - stability problems ...?

currently my Message Interval is 1000msec
but this is for outgoing/sending messages only ... i think?

i correct the settings within my home control (FHEM) and send the control message one time once (instead 10 times)
now it works for days without problems.
i will report new problems as they occur.
by dirk_k
02 Jul 2018, 15:34
Forum: ESP Easy: Hardware
Topic: SOnoff 4ch espeasy issue
Replies: 5
Views: 176

Re: SOnoff 4ch espeasy issue

The problem connecting to the web-gui are from MQTT connection problems (within my environment) Wait 2-3 minutes and try again. Connecting serial send & serial receive (RX&TX) while rebooting erase the config (starting with some FW-version i don't remember) Flashing the 1MB file may work too. (but n...
by dirk_k
02 Jul 2018, 11:49
Forum: ESP Easy: Software
Topic: MQTT Import - stability problems ...?
Replies: 12
Views: 678

Re: MQTT Import - stability problems ...?

I use only one MQTT Import with only one value. But because a non optimal software configuration i send the value 20 times per minute (10 times within 2-3 seconds). After some hours the ESP-Easy don't get new/changed MQTT values. I open the webpage and check this within device-view. An external MQTT...
by dirk_k
02 Jul 2018, 11:00
Forum: ESP Easy: Software
Topic: Serial input to MQTT
Replies: 2
Views: 237

Re: Serial input to MQTT

i use the following syntax

On Serial#myname do
publish home/ESP07/Alarm,[Serial#myname]
Endon
by dirk_k
14 Jun 2018, 10:48
Forum: ESP Easy: Software
Topic: MQTT Import - stability problems ...?
Replies: 12
Views: 678

Re: MQTT Import - stability problems ...?

Hi waspi, which firmware do you use. With "older" fw (last year) i don't see such problems too, but i flash the current because the "wlan-setting-writes kill the flash" problem. i configure another ESP (NodeMCU), point to the same MQTT topic for import and get the same result. Booth devices stops wo...
by dirk_k
13 Jun 2018, 17:02
Forum: ESP Easy: Software
Topic: MQTT - problems over slow connection
Replies: 1
Views: 149

MQTT - problems over slow connection

Hi, i have connection problems using MQTT over 3G-connection (limited to 28kbps). 2 other ESP-devices (using arduino IDE-code) send and receive MQTT data without problems. The ESP-Easy devices send and receive MQTT data too until i upgrade the firmware to current version. The old code is from middle...
by dirk_k
04 Jun 2018, 17:39
Forum: ESP Easy: Software
Topic: MQTT Import - stability problems ...?
Replies: 12
Views: 678

MQTT Import - stability problems ...?

Hi all, i use SonOff S20 to control my dehumidifier. FHEM send every minute a MQTT message to restart the Count-Down-Timer. Works fine after ESP restart. But after some time (1-2h) the MQTT import stops reading MQTT messages. The counter expires and the dehumidifier stops working. Manually send MQTT...
by dirk_k
23 May 2018, 16:53
Forum: Experimental
Topic: Wifi Wizard Setup Loop
Replies: 38
Views: 3440

Re: Wifi Wizard Setup Loop

i upgrade one of my sonoff-basic devices these year. (don't know the date or version) i get wifi problems since upgrade. device lost WLAN and built i'ts own. Thats as expected. But if my WLAN is back the device don't go back to my WLAN and it#s own WLAN keeps active for days/weeks/or.. . I have to d...
by dirk_k
25 Apr 2018, 21:11
Forum: ESP Easy: General Discussion
Topic: ESP-Chip (Rules) not running without WLAN?
Replies: 1
Views: 573

Re: ESP-Chip (Rules) not running without WLAN?

The new S20 device with current software mostly don't have this problem.
Seems the MQTT connection is the source of the problem.
With current firmware i have to wait some seconds and the switch is working without WLAN too.
by dirk_k
08 Apr 2018, 17:44
Forum: ESP Easy: Software
Topic: High CPU Load and crashes with LongPulse or Timer
Replies: 0
Views: 224

High CPU Load and crashes with LongPulse or Timer

Hello all, i use ESP Easy at Sonoff-S20. Works great, but sometimes the system crashes. I start monitoring system variables. (CPU load, Memory, uptime, ...) After some uptime i see high CPU load (70%) while using LongPulse. Crashes i see only while CPU load is high. i switch to the timer function. B...