Search found 21 matches
- 22 Jan 2019, 15:22
- Forum: ESP Easy: Software
- Topic: Rules Help
- Replies: 13
- Views: 7138
Re: Rules Help
At first you wrote you switch gpio13 by pulling it up. But in your first configuration screenshot I can see internal pullup enabled. So your gpio13 is on log. 1 in standby and you must switch to ground and check log. low state when switch is pressed. You are right... haven't seen this. @angelo-fili...
- 22 Jan 2019, 10:45
- Forum: ESP Easy: Software
- Topic: Rules Help
- Replies: 13
- Views: 7138
Re: Rules Help
At first you wrote you switch gpio13 by pulling it up. But in your first configuration screenshot I can see internal pullup enabled. So your gpio13 is on log. 1 in standby and you must switch to ground and check log. low state when switch is pressed. You are right... haven't seen this. @angelo-fili...
- 21 Jan 2019, 15:56
- Forum: ESP Easy: Software
- Topic: Rules Help
- Replies: 13
- Views: 7138
Re: Rules Help
How long should gpio 14 be 1? As long as gpio 13 is 1 or should gpio 13 toggle 14? as long as gpio13 is 1: on Switch1#State do if [Switch1#State]=1 gpio,14,1 else gpio,14,0 endif endon Don*t know why you use the timer in this Case (toggle everytime gpio 13 gets 1) i use Dummy Device (task12, Name = ...
- 20 Jan 2019, 22:09
- Forum: ESP Easy: Software
- Topic: 100% load when mqtt broker not reachable
- Replies: 0
- Views: 1904
100% load when mqtt broker not reachable
I have a question. I have configured lamps and switches on my ESP8266. For example, if the MQTT Broker fails, the ESP are almost impossible to operate. Load at 100%. If I deactivate the MQTT at the ESP for the time period my broker is down (hab a defective SD), everything can be operated directly vi...
- 31 Dec 2018, 16:41
- Forum: ESP Easy: General Discussion
- Topic: State not working??
- Replies: 22
- Views: 13705
Re: State not working??
You are the best.
Thanks that is what i missed..........
- 31 Dec 2018, 15:48
- Forum: ESP Easy: General Discussion
- Topic: State not working??
- Replies: 22
- Views: 13705
Re: State not working??
Sorry As far as i understand, i should not use switch for output (what i did until now). So how is the best way to get the state of an output in MQTT (f.ex. Relais) when it changes. because i changed "directly" on the esp via a switch or over MQTT. i have until now following configuration....
- 31 Dec 2018, 12:50
- Forum: ESP Easy: General Discussion
- Topic: State not working??
- Replies: 22
- Views: 13705
Re: State not working??
b. no longer need to declare an output pin as an input switch just to know its state. This alone saves up allot of the just 12 available tasks. status,gpio,<pin number> does just that. (once you set gpio the first time at after boot) -D You use the switch event to trigger the event toggleLED. This ...
- 31 Dec 2018, 12:26
- Forum: ESP Easy: General Discussion
- Topic: What the simplest way to blink diode with 100ms rate continuously?
- Replies: 2
- Views: 2515
Re: What the simplest way to blink diode with 100ms rate continuously?
Hi why don't take a blink-LED?
Noting easer than this.
100ms? I find this very fast.
Noting easer than this.
100ms? I find this very fast.
- 24 Dec 2018, 17:32
- Forum: ESP Easy: General Discussion
- Topic: State not working??
- Replies: 22
- Views: 13705
Re: State not working??
Hmm I used Switch for relais (output) too, because state is send vie MQTT right after change. If you use a Dummy like grovkillen said, you have the problem that state is send not directly after change. Ok ou can change the intervall, but in this case it sends the state every x sec. not only after ch...
- 17 Dec 2018, 19:51
- Forum: ESP Easy: General Discussion
- Topic: Rules Example for new feature doubleklick and longpress
- Replies: 15
- Views: 15984
Re: Rules Example for new feature doubleklick and longpress
Hi. With slow Button activated doesnt make any difference. Following Rules for testing activ: on io4#io4=1 do if [io14#io14]=0 GPIO,14,1 else GPIO,14,0 endon on IO4#io4=3 do if [io12#io12]=0 GPIO,12,1 else GPIO,12,0 endon on IO4#io4=11 do if [io13#io13]=0 GPIO,13,1 else GPIO,13,0 endon -----> short ...
- 17 Dec 2018, 08:45
- Forum: ESP Easy: General Discussion
- Topic: Rules Example for new feature doubleklick and longpress
- Replies: 15
- Views: 15984
Re: Rules Example for new feature doubleklick and longpress
Hi i do have the same issue as Cino2424. Looking at mqtt at the same time i can see that first a 1 and then (if i am Lucky) a 3 is send on doubleclick. I think ther should be a function, if i use this features, sending of the "new" state must be delayed. Otherwise i get a "normal"...
- 16 Jun 2018, 18:43
- Forum: ESP Easy: Software
- Topic: set GPIO state other than 0 or 1
- Replies: 1
- Views: 1892
Re: set GPIO state other than 0 or 1
Normally a GPIO has two states, 0 and 1. Anything else don't make any sense and will not work. Only in PWM-Mode you have a value from 0 to 1023, that is why only 0 and 1 is shown within GPIO-State. I don't really understand "Would like to use this for state controlling and request state by URL....
- 03 Jun 2018, 10:36
- Forum: ESP Easy: Software
- Topic: No Publish after Deep Sleep
- Replies: 15
- Views: 10987
Re: No Publish after Deep Sleep
Hi.
OK i will try this version.
Thanks.
OK i will try this version.
Thanks.
- 02 Jun 2018, 17:51
- Forum: ESP Easy: Software
- Topic: MQTT unsubscribe
- Replies: 0
- Views: 1565
MQTT unsubscribe
Hi. I am using ESPEasy with MQTT and IOBroker with deep sleep. Now i get always an error message within IOBroker MQTT Log, because the connection to MQTT get "hard" interruptet because of deep sleep. Is there a possibility to unsubscribe MQTT before entering deep sleep? f.ex: on System#Sle...
- 28 Apr 2018, 13:53
- Forum: ESP Easy: Software
- Topic: Plugin for RFID Reader RDM6300
- Replies: 15
- Views: 16095
Re: Plugin for RFID Reader RDM6300
When i try to compile with this plugin i allways get an error.
invalid conversion from 'unsigned int*' to 'int' [-fpermissive]
event->idx = Settings.TaskDeviceID[index];
Regards Peter
invalid conversion from 'unsigned int*' to 'int' [-fpermissive]
event->idx = Settings.TaskDeviceID[index];
Regards Peter
- 28 Apr 2018, 13:03
- Forum: ESP Easy: Software
- Topic: RFID Plugin Error
- Replies: 2
- Views: 2607
RFID Plugin Error
Hi i would like to use RFID RDM6300 with the ESPEasy.
When i try to select the plugin an Error messages comes up.
What am i doing wrong?
Regards Peter
When i try to select the plugin an Error messages comes up.
What am i doing wrong?
Regards Peter
- 27 Apr 2018, 12:05
- Forum: ESP Easy: Software
- Topic: No Publish after Deep Sleep
- Replies: 15
- Views: 10987
No Publish after Deep Sleep
Hi i am using a battery powered temperature and pressure unit. After i tried ESPMega 20180422 up to 20180426. In all of this version i don't get the new values in my Broker. OLD Version (which is working): INIT : Booting version: (custom) INIT : Rebooted from deepsleep #12 FS : Mounting... FS : Moun...
- 08 Mar 2018, 18:29
- Forum: ESP Easy: Software
- Topic: Can't PUBLISH at System#Boot
- Replies: 3
- Views: 3058
Re: Can't PUBLISH at System#Boot
Hi
Take a look at this one
viewtopic.php?f=6&t=4989
Publish is running BEFORE connect to the MQTT Broker.
Take a look at this one
viewtopic.php?f=6&t=4989
Publish is running BEFORE connect to the MQTT Broker.
- 08 Mar 2018, 17:50
- Forum: ESP Easy: Software
- Topic: MQTT-connect event
- Replies: 14
- Views: 11283
Re: MQTT-connect event
VCC-Option?
What exactly does that mean.
What exactly does that mean.
- 08 Mar 2018, 15:07
- Forum: ESP Easy: Software
- Topic: MQTT-connect event
- Replies: 14
- Views: 11283
Re: MQTT-connect event
I went back to Mega 20180104. In this version the on system#boot do works.
Hope it will be fixed in later releases again
In the ne versions the ESP is also connected to the MQTT with ESP_"MACADRESS" and not with the name given in the SW ex: ESP_TAB4
Peter
Hope it will be fixed in later releases again
In the ne versions the ESP is also connected to the MQTT with ESP_"MACADRESS" and not with the name given in the SW ex: ESP_TAB4
Peter
- 24 Nov 2017, 11:41
- Forum: ESP Easy: Projects / Applications
- Topic: Finished: H801 RGBWW control with openhab2 and mqtt
- Replies: 35
- Views: 53124
Re: Finished: H801 RGBWW control with openhab2 and mqtt
Had the same problem, wanted to use home assistant and mqtt. But whatever I tried I was unable to get them to talk to eachother, so I did abandon esp easy and used a simpler script found on the internet. The difficulty for newbies trying to solve things and getting stuck is that most people who get...