I have finally been able to flash the latest build (v2.0-20180220) on my sonoff basic. Now I can continue with the actual problem. If I want to switch my sonoff the signal seems to be pingpong so the sonoff switches on and off several times. What have I done now: I have 1 virtual switch in domoticz ...

No I think it is a normal 8266 chip, my terminal says: when I try to flash it with a prebuild 8285 version.

I tried this with my terminal: sudo python esptool.py --baud 115200 --port /dev/tty.SLAB_USBtoUART write_flash -fm dout 0x00000 ~/Downloads/ESP_Easy_v2.0-20180218_dev_ESP8266_1024.bin The flash has succeeded but no esp_0. Because I have previously experienced this I read a tip that I can solve this ...

It takes me the hole morning tot update my sonoff basic with the newest ESPsoftware and no succes. All the different versions maks me crazy. I used Aduino IDE 1.8.4 ESP Release v2.0-20180218 A Sonoff Basic (recent) Board: ESP8266 version 2.3.0 (when I update this to latest 2.4.0. I get a message tha...

Or right. It takes me the hole morning tot update the sonoff with the newest espsoftware and no succes. All the different versions maks me crazy. I used Aduino IDE 1.8.4 (also tried 1.8.5) ESP Release v2.0-20180218 (latest) A Sonoff Basic (recent) Board: ESP8266 version 2.3.0 (when I update this to ...

I used the Arduino IDE (1.8.5) to flash my Sonoff. ReleaseNotes of my ESP-software: // Rxxx 02-12-2016 EasyMega build (experimental) // Native SPIFFS support, old custom flash routines removed // Support OTA up to 1.5MB sketch size (change to 1M SPIFFS model) on 4M modules // Fallback Wifi AP suppor...

Config:

It' s version 2.0.
Both switches are normal switches:


When I use the domoticzswitch I hear switch the sonoffrelay but not one time but a couple of times.

This is my main page (build 2-2): https://imageshack.com/a/img924/8620/NRD9ic.png Devices: https://imageshack.com/a/img922/2986/0JCmgN.png Rules: on lamp_on do gpio,12,1 gpio,13,0 endon on lamp_off do gpio,12,0 gpio,13,1 endon on lamp_change do if [rele#Switch]=1 event,lamp_off SendToHTTP 10.0.1.32,...

I tried your script Vader and use one device SW01 in the GUI ESP but this doesnt work. The domoticz switch doesnt work at all and the wallswitch works sometimes.

Or right thanx for your reaction. I tried this script. What have I done: In de GUI ESP easy I submit two task under 'devices' of my sonoff: 1 switch GPIO12, IDX 1266, called 'rele' ' and 1 switch GPIO14, IDX 1, called ' SW01' In Domoticx I submit a virtual switch with IDX1266. Now I used the script ...

I want to controll my sonoff with esp easy 2.2 also control with my wall switch witch gpio14. So i connect it with gpio14 and ground and submit a switch on port gpio14 in the espeasy GUI. Nothing happened when i flip the hardwareswitch. What am I doing wrong?

Solved. After a hardreset of the wemos it works!

If you mean how long the wemos online was: 0 days 5 hours 13 minutes.
Is that what you were asking?

It communicating by HTTP. I run version ESP easy 2.0.0- dev12

I would like to make a wifi / ITFF button with a Wemos d1 mini. I therefore connected a button to my wemos (on ground and gpio 6). With this I want to switch a light on and off (domoticz). This works fine, however, to a few hours the wemos seems to fall asleep after which the button does not work. I...

Niemand ervaring met easywave?

Ik gebruik een RFlink 433 MHz en heb nu daarnaast een RFLink 868 MHz(nodoshop)draaien waarmee ik mijn zonnescherm wil aansturen. Ik heb een Brustorscherm met een afstandbediening waarop staat dat deze werkt op het Easywave protocol (868,3Mhz). Ik zie echter in mijn domoticz (op Raspberry Pi3) geen e...