rules delay to post vcc on deepsleep

[rene9900]

https://www.letscontrolit.com/wiki/index.php/SleepMode

Note that its recommended to set the Message Delay to 0 in the advanced settings page, since you want the unit to broadcast messages asap in order to save precious battery power.

Have you done this?

yes the message delay in advanced and the delay in devices on the VCC is both on 0

but on the wiki it say :
It will send all the sensor-readings at once (delays are ignored, except for Message Delay at the advanced settings page)

[grovkillen]

https://www.letscontrolit.com/wiki/index.php/SleepMode

Note that its recommended to set the Message Delay to 0 in the advanced settings page, since you want the unit to broadcast messages asap in order to save precious battery power.

Have you done this?

yes the message delay in advanced and the delay in devices on the VCC is both on 0

but on the wiki it say :
It will send all the sensor-readings at once (delays are ignored, except for Message Delay at the advanced settings page)

You're right. Maybe open a issue on Github?

[rene9900]

You're right. Maybe open a issue on Github?

i know not how

only way it works is by shortcutting positive and negative to coldboot it then it works . besides the missing delay

WIFI : Connected!
MQTT : Connected to broker
Subscribed to: /8266-3/#
INIT : Boot OK
INIT : Deep sleep enabled
INIT : Cold Boot
EVENT: System#Boot
ACT : timerSet,1,10
NTP : NTP sync requested
NTP : NTP send to 194.239.123.230
NTP : NTP replied!
EVENT: Clock#Time=Mon,13:30
pm open,type:2 0
EVENT: Rules#Timer=1
ACT : Publish /8266-3/status,8266-3_Online
ACT : Publish /8266-3/VCC,3.45
ACT : Publish /8266-3/Time,13:30
MQTT : Topic: /8266-3/status
MQTT : Payload: 8266-3_Online
MQTT : Topic: /8266-3/VCC
MQTT : Payload: 3.45
MQTT : Topic: /8266-3/Time
MQTT : Payload: 13:30
EVENT: Clock#Time=Mon,13:31
WD : Uptime 0 ConnectFailures 0 FreeMem 25624
SYS : 3.45
EVENT: #VCC=3.45
Enter deep sleep...

[Alpensepp]

Hi

Same problem here...

I use a ESP8266-12 and a BME280 Sensor with ESPEasy_mega-20180209.

The 8266 ist put in deep sleep, awakes every 300s and sends the BME280 data - perfect.

Now I started to use the ADC input to monitor the battery voltage. It works fine when the 8266 is awake all the time, but no ADC data is sent when awakening from deep sleep. The data from the BME280 is sent.

Any ideas?

best regards

Martin

I am a step further now.

When I put the ADC/VCC device as the first device in ESPEasy, the data is sent when awakening from deep sleep. But now, the BME280 data is not sent any more.
It seems, like the 8266 is going to deep sleep too fast, and therefore the last (ore later) devices are not able to send their data.

[grovkillen]

Please raise this issue up Github, referring to this thread.

[rene9900]

Please raise this issue up Github, referring to this thread.

I made a ticket on github about it.
https://github.com/letscontrolit/ESPEasy/issues/870

[grovkillen]

Please raise this issue up Github, referring to this thread.

I made a ticket on github about it.
https://github.com/letscontrolit/ESPEasy/issues/870

Great