Let's Control It

papperone wrote: ↑25 Apr 2018, 22:49 I will try to get the new schematic and as well some knowledge of the new hardware to try to implement it in ESPEasy...

@TD-er: as you defined now in current cource code my HLKW8012 plugin can be used only with Sonoff-POW, while there are few dev board with this chip (e.g. ElectroDragon) and as well I've 2 custom PCB with this circuit that uses different pins; like this I'll now be forced to always makes custom compiled for my own version of POW and I can't use the standard .BIN (which I tend to avoid in final devices due to complexity of managing upgrades via OTA)...

larduino wrote: ↑06 Jun 2018, 18:15 I received my POW yesterday . I believe it must be version 1 since I don't see any mention on box that it is version 2 .
I just soldered in 4 pin header and flashed it using ESP_Easy_mega-20180606_hard_SONOFF_POW.bin and it all went well.
It is now wired up to 110v and I put an outlet on output to test it.
I have it set up as seen in attached screenshot. The voltage shows up but I have not figured out yet how to turn the relay on so I can have a load on it to see if current is working.
Thanks for any advice.
pow.jpg

projectsun wrote: ↑15 Jun 2018, 00:26 Hello. Sorry, but where do I get this file: ESP_Easy_mega-20180524_hard_SONOFF_POW.bin

projectsun wrote: ↑15 Jun 2018, 00:26 Hello. Sorry, but where do I get this file: ESP_Easy_mega-20180524_hard_SONOFF_POW.bin

TD-er wrote: ↑14 Jun 2018, 19:03 At this moment, if you want to split values from one plugin over multiple IDX, you have to use rules to do so.

For example, I use this on my node with SDS011 to upload to Domoticz:

Code: Select all

On System#Boot do //This will happen at boot ESP8266
   timerSet,1,30  //Set and start timer 1 at 30 seconds
endon
 
On Rules#Timer=1 do   //When the timer 1 is up:
  SendToHTTP 192.168.1.28,8080,/json.htm?type=command&param=udevice&idx=105&nvalue=0&svalue=[SDS011#PM25] //Send the PM2,5 data to Domoticz
  SendToHTTP 192.168.1.28,8080,/json.htm?type=command&param=udevice&idx=108&nvalue=0&svalue=[SDS011#PM10] ////Send the PM10 data to Domoticz
  timerSet,1,120                //Set the next cycle at 120 seconds 
endon

On Living_Radiator_In#Temp_3 do
TaskValueSet 7,1,[Living_Radiator_In#Temp_3]-[Living_Radiator_Out#Temp_4]
endon

Prutsium wrote: ↑15 Jun 2018, 10:32

TD-er wrote: ↑14 Jun 2018, 19:03

Ok noticed making dummies is more work so the result:

Code: Select all

On POW_2_Sensors#POW_2_Voltage do
SendToHTTP 192.168.99.5,8080,/json.htm?type=command&param=udevice&idx=93&nvalue=0&svalue=[POW_2_Sensors#POW_2_Voltage] //Send the Voltage data to Domoticz
SendToHTTP 192.168.99.5,8080,/json.htm?type=command&param=udevice&idx=94&nvalue=0&svalue=[POW_2_Sensors#POW_2_Power] //Send the Watt data to Domoticz
SendToHTTP 192.168.99.5,8080,/json.htm?type=command&param=udevice&idx=95&nvalue=0&svalue=[POW_2_Sensors#POW_2_Current] //Send the Amp data to Domoticz
SendToHTTP 192.168.99.5,8080,/json.htm?type=command&param=udevice&idx=96&nvalue=0&svalue=[POW_2_Sensors#POW_2_Pulses] //Send the Usage data to Domoticz
endon

Where the On POW_2_Sensors#POW_2_Voltage triggers the sending of the data instead of a timer.
All values come now in at Domoticz but have some issues with the Pulse sensor as it does not send an actual pulse but an incremental counter that resets itself after number xxx seems Domotics has some issues with it. Trying now in ESPEasy to divide the value by /1253 so Domoticz get the count as more handlable value. Not sure if it's the right thing to do will hook up the Aircon of 1KW for an hour to see if numbers are right.

Edit:
That did not work correctly As its a looping counter it goes to 65355 and back to zero afterwards ....
Resulting in first stage nice increment but after it jumped back to 0 and so on ....

Prutsium wrote: ↑15 Jun 2018, 10:26

projectsun wrote: ↑15 Jun 2018, 00:26 Hello. Sorry, but where do I get this file: ESP_Easy_mega-20180524_hard_SONOFF_POW.bin

Or use the latest version of the normal mega but the DEV version if you have the R2.
At least then you also have all the other options for additional sensors (although it requires then soldering as the internal serial port is used for the POW sensor and cant be switched to GPIO)

TD-er wrote: ↑18 Jun 2018, 21:19 Domoticz is a bit strange in processing data.
You have to deliver the data in the right format and order to match the pre-defined types.
If you want to graph them in separate charts, you have to split the values using rules.

On POW_2_Sensors#POW_2_Voltage do
SendToHTTP 192.168.99.5,8080,/json.htm?type=command&param=udevice&idx=93&nvalue=0&svalue=[POW_2_Sensors#POW_2_Voltage] //Send the Voltage data to Domoticz
SendToHTTP 192.168.99.5,8080,/json.htm?type=command&param=udevice&idx=94&nvalue=0&svalue=[POW_2_Sensors#POW_2_Power] //Send the Watt data to Domoticz
SendToHTTP 192.168.99.5,8080,/json.htm?type=command&param=udevice&idx=95&nvalue=0&svalue=[POW_2_Sensors#POW_2_Current] //Send the Amp data to Domoticz
SendToHTTP 192.168.99.5,8080,/json.htm?type=command&param=udevice&idx=96&nvalue=0&svalue=[POW_2_Sensors#POW_2_Pulses] //Send the Usage data to Domoticz
endon

pa3gmi wrote: ↑18 Jun 2018, 14:42 Hi,
I have the sonoff Pow and did a flasch with ESP_Easy_mega-20180524_hard_SONOFF_POW.bin. I can see the values on the device direct, but only the voltage in Domoticz, I do not understand the way to see all the values, here mentioned by Prutsium, please will You tell me more about that. I am not a programmer 70 years old but I want to learn always something.

TD-er wrote: ↑18 Jun 2018, 21:36 Support for the POW devices is still very beta (if not alpha), so all suggestions to improve are more than welcome.

But when I flash this hard_POW bin to my POW ver 2.0 (not R2), after flash complete nothing happens... no webif, no ping, no ESPEasy_0. After flashing a normal or dev bin, ping is there again.
What did I do wrong?

(Tested with 20180524_hard_SONOFF_POW, 20180606_hard_SONOFF_POW, 20180615_hard_SONOFF_POW) all the same. CSE7759 is present.

pa3gmi wrote: ↑19 Jun 2018, 18:56 Thanks for answer, I have done as you say, but until now I can get only the Voltage readout. Is this script also sensitive for the name of the unit or somewhat else?
I have fill in my Domoticz IP and port address and made 3 virtual sensors note the IDX and fill in on the right place, what else can or must I do. Has the Device self an IDX?
Thanks for your patience

pa3gmi wrote: ↑20 Jun 2018, 09:13 This is the software version I have: The POW print is ver 2
Build 20102 - Mega
Libraries ESP82xx Core 2_4_1, NONOS SDK 2.2.1(cfd48f3), LWIP: 2.0.3
GIT version mega-20180615

Prutsium wrote: ↑20 Jun 2018, 10:58

pa3gmi wrote: ↑20 Jun 2018, 09:13 This is the software version I have: The POW print is ver 2
Build 20102 - Mega
Libraries ESP82xx Core 2_4_1, NONOS SDK 2.2.1(cfd48f3), LWIP: 2.0.3
GIT version mega-20180615

Rien,

Try the DEV version so not the POW i run the DEV version with the CSE and all works ok for me.
( run actually this one: ESP_Easy_mega-20180606_dev_ESP8266_1024.bin )

pa3gmi wrote: ↑20 Jun 2018, 11:47 What do you mean with "the CSE"

Thanks anyway for the fast response.

pa3gmi wrote: ↑20 Jun 2018, 13:08 Hi is it possible that i have not the right POW version on the print is Ver 2.0 the measuring chip is HLW8012
With your configuration I have now no readings at all, so the measuring circuit seems not working.

Rien

sincze wrote: ↑18 Aug 2018, 13:15 The following rules will allow the POW2 to report the data to domoticz. [...]

sincze wrote: ↑18 Aug 2018, 13:31 If it is good enough for the Wiki I can add it

Djoe wrote: ↑27 Aug 2018, 09:35 Hi,

@sincze which version of mega do you use?

I have try mega_20180826 and mega_20180719, both correctly show values from CSE7759, but http push from rules doesn't work...

This rules work fine:
On WIFI#RSSI do
SendToHTTP x.x.x.x,8080,/json.htm?type=command&param=udevice&idx=88&nvalue=0&svalue=[POW#Voltage]
endon

Confirmed by logs:
Aug 26 21:32:56 POW EspEasy: SYS : -77.00
Aug 26 21:32:56 POW EspEasy: EVENT: WIFI#RSSI=-77.00
Aug 26 21:32:56 POW EspEasy: ACT : SendToHTTP x.x.x.x,8080,/json.htm?type=command&param=udevice&idx=88&nvalue=0&svalue=235.07
Aug 26 21:32:56 POW EspEasy: Command: sendtohttp

But this one is never triggered:
On POW#Current do
SendToHTTP x.x.x.x,8080,/json.htm?type=command&param=udevice&idx=89&nvalue=0&svalue=[POW#Power];[POW#Pulses]
SendToHTTP x.x.x.x,8080,/json.htm?type=command&param=udevice&idx=90&nvalue=0&svalue=[POW#Current]
endon

Greetings from Tahiti!

On System#Boot do
	TaskValueSet 5,1,0
	TaskValueSet 5,2,0
	TaskValueSet 5,3,0
EndOn

// LAMP CONTROLLING INCLUDING LED LIGHT

on lamp_on do
	gpio,12,1
	gpio,13,0
endon

on lamp_off do
	gpio,12,0
	gpio,13,1
endon

on SW_1#Switch do
	if [SW_1#Switch]=1
		gpio,12,1
		gpio,13,0
	else
		gpio,12,0
		gpio,13,1
	endif
endon

on Energy#Power do

	if Clock#Time=All,**:*0 do
		SendToHTTP x.x.x.x,8080,/json.htm?type=command&param=udevice&idx=11&nvalue=0&svalue=[Energy#Voltage]
		SendToHTTP x.x.x.x,8080,/json.htm?type=command&param=udevice&idx=18&nvalue=0&svalue=[Energy#Power]
		SendToHTTP x.x.x.x,8080,/json.htm?type=command&param=udevice&idx=13&nvalue=0&svalue=[Energy#Power]
		SendToHTTP x.x.x.x,8080,/json.htm?type=command&param=udevice&idx=14&nvalue=0&svalue=[Energy#Current]
	endif
				
	if [Energy#Voltage]!=[Calculation#Voltage]
		SendToHTTP x.x.x.x,8080,/json.htm?type=command&param=udevice&idx=1&nvalue=0&svalue=[Energy#Voltage] // Voltage
		TaskValueSet 5,1,[Energy#Voltage]
	endif

	if [Energy#Power]!=[Calculation#Power]
		SendToHTTP x.x.x.x,8080,/json.htm?type=command&param=udevice&idx=13&nvalue=0&svalue=[Energy#Power] // Calculated KwH.
		SendToHTTP x.x.x.x,8080,/json.htm?type=command&param=udevice&idx=18&nvalue=0&svalue=[Energy#Power] // Watt only
		TaskValueSet 5,2,[Energy#Power]
	endif

	if [Energy#Current]!=[Calculation#Current]
		SendToHTTP x.x.x.x,8080,/json.htm?type=command&param=udevice&idx=14&nvalue=0&svalue=[Energy#Current] // Amp
		TaskValueSet 5,3,[Energy#Current]
	endif
		TaskValueSet 5,4,[Energy#Pulses]

endon