ALLNET 4duino IoT WLAN ESP8266-UP-Relais - rx and tx to GPIO
Moderators: grovkillen, Stuntteam, TD-er
ALLNET 4duino IoT WLAN ESP8266-UP-Relais - rx and tx to GPIO
Hello,
i am new in this forum. I use about 20 sonoff S20 and 3 sonoff basic with espeasy. Now i flashed this device wkth the newest espeasy Mega version:
https://m.future-x.de/item/313635333639 ... 2gQAvD_BwE
It works very well. I switch my outdoor lamps with it. Now i want to use the Rx and Tx pins for GPIO. One for the bell-button, and one for a relais for the bell. But it wont work. No input or output is possible. Serial is switched of under advanced configuration. Is it possible, to adjust espeay, to work with the device?
In the atachment everything i get from the distributor.
i am new in this forum. I use about 20 sonoff S20 and 3 sonoff basic with espeasy. Now i flashed this device wkth the newest espeasy Mega version:
https://m.future-x.de/item/313635333639 ... 2gQAvD_BwE
It works very well. I switch my outdoor lamps with it. Now i want to use the Rx and Tx pins for GPIO. One for the bell-button, and one for a relais for the bell. But it wont work. No input or output is possible. Serial is switched of under advanced configuration. Is it possible, to adjust espeay, to work with the device?
In the atachment everything i get from the distributor.
- Attachments
-
- ALL_Relais.zip
- (2.98 MiB) Downloaded 237 times
-
- allnet.zip
- (92.59 KiB) Downloaded 240 times
Re: ALLNET 4duino IoT WLAN ESP8266-UP-Relais - rx and tx to GPIO
Hello,
no chance, to get it work?
This docu i have also:
no chance, to get it work?
This docu i have also:
- Attachments
-
- 148814.zip
- (425.02 KiB) Downloaded 215 times
- grovkillen
- Core team member
- Posts: 3621
- Joined: 19 Jan 2017, 12:56
- Location: Hudiksvall, Sweden
- Contact:
Re: ALLNET 4duino IoT WLAN ESP8266-UP-Relais - rx and tx to GPIO
How do you connect the switch? Do you short it by putting GND to the pin?
ESP Easy Flasher [flash tool and wifi setup at flash time]
ESP Easy Webdumper [easy screendumping of your units]
ESP Easy Netscan [find units]
Official shop: https://firstbyte.shop/
Sponsor ESP Easy, we need you
ESP Easy Webdumper [easy screendumping of your units]
ESP Easy Netscan [find units]
Official shop: https://firstbyte.shop/
Sponsor ESP Easy, we need you
Re: ALLNET 4duino IoT WLAN ESP8266-UP-Relais - rx and tx to GPIO
I use GPIO 5 (SCL) for lightswitch. GPIO4 (SDA) for a led. Now i want to use GPIO 1 (Tx) for Bell-Button, and GPIO2 (Rx) for a relais for the bell.
Re: ALLNET 4duino IoT WLAN ESP8266-UP-Relais - rx and tx to GPIO
Some pictures of my settings
- Attachments
-
- Screenshot_20180518-164902.png (84.87 KiB) Viewed 5740 times
Re: ALLNET 4duino IoT WLAN ESP8266-UP-Relais - rx and tx to GPIO
Once more
- Attachments
-
- Screenshot_20180518-164922.png (81.04 KiB) Viewed 5736 times
- grovkillen
- Core team member
- Posts: 3621
- Joined: 19 Jan 2017, 12:56
- Location: Hudiksvall, Sweden
- Contact:
Re: ALLNET 4duino IoT WLAN ESP8266-UP-Relais - rx and tx to GPIO
So you have the gnd connected to the switch/button?
ESP Easy Flasher [flash tool and wifi setup at flash time]
ESP Easy Webdumper [easy screendumping of your units]
ESP Easy Netscan [find units]
Official shop: https://firstbyte.shop/
Sponsor ESP Easy, we need you
ESP Easy Webdumper [easy screendumping of your units]
ESP Easy Netscan [find units]
Official shop: https://firstbyte.shop/
Sponsor ESP Easy, we need you
Re: ALLNET 4duino IoT WLAN ESP8266-UP-Relais - rx and tx to GPIO
Hello,
I tested it on GND (settings: normal switch) . The relais once on GND (settings: push botton active high) and on 3,3V (settings: push button active low). Nothing work.
I tested it on GND (settings: normal switch) . The relais once on GND (settings: push botton active high) and on 3,3V (settings: push button active low). Nothing work.
- grovkillen
- Core team member
- Posts: 3621
- Joined: 19 Jan 2017, 12:56
- Location: Hudiksvall, Sweden
- Contact:
Re: ALLNET 4duino IoT WLAN ESP8266-UP-Relais - rx and tx to GPIO
Please take good pictures so I can see what you have done. If possible, use colors for the wires (black for GND etc) so I understand more.
ESP Easy Flasher [flash tool and wifi setup at flash time]
ESP Easy Webdumper [easy screendumping of your units]
ESP Easy Netscan [find units]
Official shop: https://firstbyte.shop/
Sponsor ESP Easy, we need you
ESP Easy Webdumper [easy screendumping of your units]
ESP Easy Netscan [find units]
Official shop: https://firstbyte.shop/
Sponsor ESP Easy, we need you
Re: ALLNET 4duino IoT WLAN ESP8266-UP-Relais - rx and tx to GPIO
It works
Relais i used was bad. To much power consumention. Switch works, too. Need to use "internal pullup"
Thanks
Relais i used was bad. To much power consumention. Switch works, too. Need to use "internal pullup"
Thanks
- grovkillen
- Core team member
- Posts: 3621
- Joined: 19 Jan 2017, 12:56
- Location: Hudiksvall, Sweden
- Contact:
Re: ALLNET 4duino IoT WLAN ESP8266-UP-Relais - rx and tx to GPIO
Yes I'd recommend it to be sure to have the value high when the switch is NO.
ESP Easy Flasher [flash tool and wifi setup at flash time]
ESP Easy Webdumper [easy screendumping of your units]
ESP Easy Netscan [find units]
Official shop: https://firstbyte.shop/
Sponsor ESP Easy, we need you
ESP Easy Webdumper [easy screendumping of your units]
ESP Easy Netscan [find units]
Official shop: https://firstbyte.shop/
Sponsor ESP Easy, we need you
Who is online
Users browsing this forum: No registered users and 1 guest