Search found 32 matches

by ut1545
18 Jun 2023, 20:45
Forum: ESP Easy: General Discussion
Topic: ESPEasy stability in not a problem
Replies: 1
Views: 1758

ESPEasy stability in not a problem

Hello all, As you can see, this device is running for more than 2 years without problems. Sometimes, I have to "hot swap" a I2C module or add a new one and everything remains working. Really rock solid. Actually, there are 4xPCF8574 and one BME280 connected to it and running under a UPS. T...
by ut1545
27 May 2022, 17:18
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 42264

Re: Unable to run "max" firmware into a ESP-32 16MB

Yes, it works.....

After a few tests, everything seams to work as expected except that Chip Model is detected as ESP32-D0WDQ5-V3 instead of ESP32-D0WD-V3.

Thanks a lot for your support and knowledge.
by ut1545
27 May 2022, 13:20
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 42264

Re: Unable to run "max" firmware into a ESP-32 16MB

TD-er, I have been make some tests in order to go ahead with this issue but my limited knowledge of this matter doesn't allow me to reach a success solution so, this was what I have done: - I have compiled last version of Tasmota in order to generate a 16MB compatible firmware. - I uploaded it into ...
by ut1545
20 May 2022, 18:23
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 42264

Re: Unable to run "max" firmware into a ESP-32 16MB

Hi TD-er I have flashed a "normal" 4MB image (ESP_Easy_mega_20220427_normal_ESP32_4M316k-factory.bin) and surprise, only 4MB are detected. I have found that the ESP Chip Model is incorrect also: ESPEasy reports "ESP32-D0WDQ5" instead ESP32-D0WD-V3. I don't know if it is important...
by ut1545
19 May 2022, 21:39
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 42264

Re: Unable to run "max" firmware into a ESP-32 16MB

Now, I'm really sure. Using ESP_Easy_mega_20220518_max_ESP32_16M8M_LittleFS.factory.bin file and flashed both esptool and Windows GUI....
by ut1545
19 May 2022, 21:13
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 42264

Re: Unable to run "max" firmware into a ESP-32 16MB

I'm quite sure but I will try again in case I made a mistake.
by ut1545
19 May 2022, 20:49
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 42264

Re: Unable to run "max" firmware into a ESP-32 16MB

ESP_Easy_mega_20220427_max_ESP32_16M1M-factory.bin
Both via esptool on linux and Windows GUI and erasing flash previously.
by ut1545
19 May 2022, 19:07
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 42264

Re: Unable to run "max" firmware into a ESP-32 16MB

There is no output at all regarding the ESPEasy firmware? Do you mean during ESP32 boot? If so,no at all. Here is a serial boot log. After first reset message (power on reset), the ESP32 goes into a infinite loop sending messages about "SW_RESET" very quickly. ets Jul 29 2019 12:21:46 [18...
by ut1545
19 May 2022, 09:08
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 42264

Re: Unable to run "max" firmware into a ESP-32 16MB

Thanks for your replay.
I have followed your instructions but the results are the same. Flashed with both esptool.py and Espressif GUI tool.
I'm glad to do any test that you want.....
Thanks again.
by ut1545
18 May 2022, 19:20
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 42264

Unable to run "max" firmware into a ESP-32 16MB

Hello everybody, I just received my first 2 ESP-32 with 16MB flash. Of course, I didn't wait a microsecond to load the "max" version of ESPEasy firmware but I couldn't be successful. Those are my test results: - The modules are ESP32-WROOM-32E and ESP32-WROOM-32UE both with 16MB flash. - T...
by ut1545
18 Apr 2021, 16:42
Forum: ESP Easy: Software
Topic: I2C bus error - PN532
Replies: 2
Views: 5689

Re: I2C bus error - PN532

Thank you Thomas,

I will do some tests to see if adjusting Stretch Limit could resolve this issue.

BTW, I think that if older versions can detect bus errors, the newer ones could do the same. May be the right thing to do is open an issue or PR in GitHub....

Antonio,
by ut1545
15 Apr 2021, 19:22
Forum: ESP Easy: Software
Topic: I2C bus error - PN532
Replies: 2
Views: 5689

I2C bus error - PN532

I have a self built ESP8266 with a PN532 connected to it that has worked for months. After some hardware modifications, I have updated ESPEasy from build 20191127 to the last one. After that, when I turned on and off several times a low power light (5W), the PN532 stops working until it is reset thr...
by ut1545
08 Jul 2018, 18:26
Forum: ESP Easy: Hardware
Topic: Support for PZEM 004T Energy monitor
Replies: 309
Views: 6656364

Re: Support for PZEM 004T Energy monitor

Hello, I'm trying to compile last ESPeasy V2.0 release (ESPEasy-2.0-20180510) but I'm getting the same errors as #71 http://www.letscontrolit.com/forum/viewtopic.php?p=22585#p22585. Did anyone solve this issue? How to compile this plug in under the latest releases of ESPeasy software? Thanks in adva...
by ut1545
18 Feb 2018, 18:32
Forum: ESP Easy: Hardware
Topic: Longer Range?
Replies: 13
Views: 14441

Re: Longer Range?

May be I'm so lucky... :D

I have had only one in my hands so, it may be an exception. It is marked as AI-Thinker but I know that there are a lot of fake chips around...

BTW, I'm using it just to extend range and works great...

Regards,
by ut1545
18 Feb 2018, 17:46
Forum: ESP Easy: Hardware
Topic: Longer Range?
Replies: 13
Views: 14441

Re: Longer Range?

Hi Shardan, I have a esp-07 without "S" and I can confirm that it has 1MBytes memory as you can see bellow: $ esptool.py --port /dev/ttyUSB0 flash_id esptool.py v2.1 Connecting.... Detecting chip type... ESP8266 Chip is ESP8266 Uploading stub... Running stub... Stub running... Manufacturer...
by ut1545
26 Nov 2017, 12:34
Forum: ESP Easy: Software
Topic: DNS hostname
Replies: 8
Views: 9799

Re: DNS hostname

+1 vote to have the option to select host name format...... Or in my particular case, no unit number at all.....
by ut1545
23 Nov 2017, 18:53
Forum: ESP Easy: Software
Topic: DNS hostname
Replies: 8
Views: 9799

Re: DNS hostname

Technically, both ways are the same but, I think that host names were created to make easier to remember a familiar name than a IP address. If the UnitNumber is added to host name, it is more difficult to remember the "Familiar Name": you have to remember not only the name but also UnitNum...
by ut1545
23 Nov 2017, 12:29
Forum: ESP Easy: Software
Topic: DNS hostname
Replies: 8
Views: 9799

DNS hostname

Hello all, I'm testing ESPeasy Mega and have loaded ESPEasy_v2.0.0-dev12_dev_4096.bin on a ESP-12F. Everything seams to work ok but I have found the following issue: When ESPeasy is configured to request IP address by DHCP, the host name that it sends to DNS server is "UnitName_UnitNumber"...
by ut1545
10 Nov 2017, 20:23
Forum: ESP Easy: Hardware
Topic: Support for PZEM 004T Energy monitor
Replies: 309
Views: 6656364

Re: Support for PZEM 004T Energy monitor

Hello all, Just a few words about PZEM 004T: I have implement one PZEM connected to a ESP-12F and running a very simple custom sketch. It is installed at very beginning of the incoming electrical line so, it should measure the same as the meter of electrical provider. After 11 months comparing the t...
by ut1545
25 Sep 2017, 13:48
Forum: ESP Easy: Software
Topic: GPIO pin status at rules engine
Replies: 9
Views: 15230

Re: GPIO pin status at rules engine

Hi, Thank you for your response. Your suggestion, setting dummy variables, is a good solution. BTW, I'm looking for a new approach. I will explain the idea if it can be useful for other people. I'm controlling a irrigation system through openHab controller so, when it is time to start a irrigation z...
by ut1545
21 Sep 2017, 21:05
Forum: ESP Easy: Software
Topic: GPIO pin status at rules engine
Replies: 9
Views: 15230

Re: GPIO pin status at rules engine

Hello, I'd like to do the same as hiihoo. My ESP Easy node is controlling 16 relays so, it is not desirable to have to define 16 switches devices only to know gpio state in a rule. Those relays are activated/deactivated by an openHab controller and in specific situations, I need to know gpio states....
by ut1545
17 Jan 2017, 10:40
Forum: Experimental
Topic: ESP Easy Mega
Replies: 249
Views: 634233

Re: ESP Easy Mega

Thank you BerndJ.

Ready to play with it now.....
by ut1545
16 Jan 2017, 21:57
Forum: Experimental
Topic: ESP Easy Mega
Replies: 249
Views: 634233

Re: ESP Easy Mega

Hello BerndJ,

In your previous post you say that you have compiled ESP Easy Mega so, I guess you have a pointer to source code. If so, could you please share it with us?

Thanks in advance,
by ut1545
13 Jul 2016, 22:24
Forum: ESP Easy: Software
Topic: MQTT : Failed to connected to broker
Replies: 41
Views: 56110

Re: MQTT : Failed to connected to broker

Hi all, I have tested the R109 with 2.6 library and everything seams to work ok. After the IP connection to the broker has been restored, ESP Easy reconnects immediately and stays connected. I will continue to test this version and will keep all of you informed. Good work Martinus and thank you very...
by ut1545
06 Jul 2016, 21:11
Forum: ESP Easy: Software
Topic: MQTT : Failed to connected to broker
Replies: 41
Views: 56110

Re: MQTT : Failed to connected to broker

Hello all, I have found this problem in all versions that I have tried since R78. Once ESP Easy lost the IP connection with MQTT broker, it can't connect again entering in a infinite loop. Doesn't matter if the ESP lost wifi connection or MQTT server goes down. I have tried to change the ESP Easy co...
by ut1545
02 Jun 2016, 19:44
Forum: ESP Easy: Hardware
Topic: PCF8574 and MQTT
Replies: 0
Views: 3089

PCF8574 and MQTT

Hello all,

I have tried to find any information about how to change a PCF8574 output pin state using a MQTT message without success. Has anyone know how to do that?

Any information will be appreciated....
by ut1545
01 Jun 2016, 12:17
Forum: ESP Easy: Hardware
Topic: PCF8574 - How does it work ?
Replies: 33
Views: 21193

Re: PCF8574 - How does it work ?

Any news about how to control PCF8574 via MQTT?
by ut1545
24 May 2016, 18:07
Forum: ESP Easy: Hardware
Topic: Wifi IoT Relay Board Based on ESP8266
Replies: 7
Views: 12622

Re: Wifi IoT Relay Board Based on ESP8266

Hi grz3,

Just now, I don't have any I2C device available but, as soon as I get one, I will test it and tell you the results.....
by ut1545
24 May 2016, 13:25
Forum: ESP Easy: Hardware
Topic: Wifi IoT Relay Board Based on ESP8266
Replies: 7
Views: 12622

Re: Wifi IoT Relay Board Based on ESP8266

Hello all, I just received 2 of this units. My first impressions - Load ESPEasy R106 without any problems. - The built quality is very similar to Sonoff hardware. - It has 2 relays on board (only NO contacts) - It has a 12 pin header with most GPIO exposed. - There is a place to connect a DHT22. You...
by ut1545
23 Mar 2016, 00:09
Forum: ESP Easy: Software
Topic: R91 Bugs
Replies: 11
Views: 9734

Re: R91 Bugs

Hi, Another little bug: If you setup a HC-SR04 ultrasonic distance meter, you don't have the option to specify the decimal places so, the data reported is alway a integer value. Some times it is important to have the exact value in order to calculate averages, max and min as well as establish an err...
by ut1545
22 Mar 2016, 21:39
Forum: ESP Easy: Software
Topic: R91 Bugs
Replies: 11
Views: 9734

R91 Bugs

Hello, I have discovered 2 bugs in R91 release (I don't know if they did exist previously). 1 - If you setup a sensor as Task 1, once clik submit , the fields NAME and VALUE NAME are not stored in flash memory so, next time that you try to edit the task, these values are missing. Also, the names are...
by ut1545
22 Mar 2016, 21:06
Forum: Introduce yourself
Topic: Hello from Spain
Replies: 1
Views: 5920

Hello from Spain

Hi all, My name is Antonio and I'm from Madrid, Spain. I'm trying to automate my house, actually using ESPEasy+MQTT+OpenHab. I think that this setup could be a very good solution. I would like to contribute to this magnific project but, since my C programing skills are very limited, I will try to he...