Search found 11 matches
- 20 Nov 2016, 09:20
- Forum: ESP Easy: Software
- Topic: Get variable value via http?
- Replies: 5
- Views: 5742
Re: Get variable value via http?
Is this documented on the Wiki?
- 16 Nov 2016, 15:09
- Forum: ESP Easy: Software
- Topic: How to change SSID?
- Replies: 3
- Views: 3558
Re: How to change SSID?
When I connect using 57600 or 115200 or 9600 I don't get any response from the board.
Are you sure this works with ESPEASY firmware? or do I need a different baud rate?
Are you sure this works with ESPEASY firmware? or do I need a different baud rate?
- 16 Nov 2016, 12:48
- Forum: ESP Easy: Software
- Topic: How to change SSID?
- Replies: 3
- Views: 3558
How to change SSID?
Hi, I want to connect my WEMOS boards to a WIFI network (SSID). My previous working network (SSID) is not available. How do I change the EASYESP to use a different SSID if I cannot access the current configuration? I have tried flashing the firmware again - via USB - but it is still inaccessible - d...
- 30 Jun 2016, 18:52
- Forum: ESP Easy: Projects / Applications
- Topic: Switch + Relay Plugin
- Replies: 5
- Views: 5350
Re: Switch + Relay Plugin
Why cant you just create a rule? Why plugin?
- 26 Jun 2016, 20:47
- Forum: ESP Easy: General Discussion
- Topic: Solved: [Display System Variables]
- Replies: 5
- Views: 5889
- 26 Jun 2016, 20:16
- Forum: ESP Easy: General Discussion
- Topic: Solved: [Display System Variables]
- Replies: 5
- Views: 5889
Re: Display System Variables
You need to define a system info device in the device page and choose which you want to use "Indicator" then you can add it to the LCD/OLED display
- 26 Jun 2016, 13:34
- Forum: ESP Easy: Software
- Topic: Feature request - invert the Wifi Status LED
- Replies: 2
- Views: 2605
Re: Feature request - invert the Wifi Status LED
The LED is internal to the ESP-12F board - I have no control of how it is connected.costo wrote:either connect your led with series resistor to Vcc or to ground.
- 25 Jun 2016, 20:25
- Forum: ESP Easy: Software
- Topic: Feature request - invert the Wifi Status LED
- Replies: 2
- Views: 2605
Feature request - invert the Wifi Status LED
I would like to see an option to invert the WIFI status LED/GPIO option in the Hardware section.
So that the LED will be on only when transmitting. now it is momentarily turned off when transmitting and on continuously - which is annoying in dark areas.
So that the LED will be on only when transmitting. now it is momentarily turned off when transmitting and on continuously - which is annoying in dark areas.
- 24 Jun 2016, 11:33
- Forum: ESP Easy: Software
- Topic: Feature request - SendtoHTTP authentication
- Replies: 6
- Views: 8819
Feature request - SendtoHTTP authentication
Is it possible to add username and password to the SendtoHTTP command? I would like my ESP to send ON/OFF/Toggle commands directly to my KMTronicC WEB relay board. http://kmtronic.com/kmtronic-lan-ethernet-ip-8-channels-web-relay-board.html There is no option to remove the authentication from it. I ...
- 24 Jun 2016, 10:05
- Forum: ESP Easy: Software
- Topic: Problem/Bug - Switch with 0 delay is not sending data on boot
- Replies: 0
- Views: 1808
Problem/Bug - Switch with 0 delay is not sending data on boot
Hello, Using R107. I have setup a switch device (pushbutton) and requested to "Send Boot state". The delay is set to 0 as I only want the state to be sent when it changes. To test: * I pressed the pushbutton so Domoticz virtual device is showing ON - OK. * ESPEASY is showing the pushbutton...
- 29 May 2016, 16:05
- Forum: ESP Easy: Hardware
- Topic: gizwits board - anybody has one?
- Replies: 16
- Views: 13008
Re: gizwits board - anybody has one?
Hi. Yep, got one. Flashed it with ESPEasy R105 and it's now monitoring my Washing Machine, Laundry room temperature and Soon to be monitoring the incoming water temperature and a flood contact! Connected to Mosquitto MQTT broker and OpenHAB Works well and easy to connect to a PSU with the USB port....