Search found 17 matches

by hugo11
24 Apr 2018, 22:46
Forum: ESP Easy: Hardware
Topic: IR Transmitter ?
Replies: 119
Views: 80087

Re: IR Transmitter ?

Hi guys, Some help needed here. I'd like to control my Marantz receiver, but the code is not recognized so obviously I will have to use RAW. I've read the complete post but I'm somehow lost how to convert to correct string. Could someone help ? first Key Unknown encoding: F5EEEEC8 (32 bits) Raw (32)...
by hugo11
04 Mar 2018, 15:37
Forum: ESP Easy: Software
Topic: Problems compiling on Arduino ...
Replies: 4
Views: 1830

Re: Problems compiling on Arduino ...

Thanks a lot for the help, spent last few figuring out what's wrong :)
by hugo11
04 Mar 2018, 15:01
Forum: ESP Easy: Software
Topic: rc-switch plugin
Replies: 62
Views: 22289

Re: rc-switch plugin

I have also issues compiling with the _P111_RF.ino included. I tried reinstaling the IDE + removed the libraries folder and only included the ones from the ESP Easy distribution.

Still the same, any other ideas?
by hugo11
10 Mar 2017, 18:17
Forum: ESP Easy: Projects / Applications
Topic: MH-Z14 / MH-Z19 CO2 sensor
Replies: 55
Views: 33106

Re: MH-Z14 / MH-Z19 CO2 sensor

maybe a tip what could help as I never had issues with light I ordered one of these cheap smoke detectors off ebay, removed the crap and installed the ESP and MHZ19 into it.. working fine. http://www.ebay.com/itm/Fire-Smoke-Sensor-Detector-Alarm-Tester-Home-Security-System-Cordless-LOT-EP-/172322507...
by hugo11
07 Jan 2017, 20:10
Forum: ESP Easy: General Discussion
Topic: Simple switch issues
Replies: 4
Views: 1111

Re: Simple switch issues

I'm on ESP12E. ok, eventually got it working. The rule is as simple as this: on Lightswitch#value do SendToHTTP 192.168.2.4,39989,/cmd?a=motion_esp05_1 endon The Switch is configured as pullup / reversed / push button active high and the gpio is connected to a PIR sensor. working absolutely fine for...
by hugo11
07 Jan 2017, 17:36
Forum: ESP Easy: General Discussion
Topic: Simple switch issues
Replies: 4
Views: 1111

Re: Simple switch issues

Thanks a lot, I've seen similar topics to that based on which I also built the rules. I'm still struggling, I think the issue is with triggering the switch on gpio 16. What I have not is a pushbutton soldered to ground, effectively grounding GPIO16 when I push the button, still the switch is still h...
by hugo11
07 Jan 2017, 17:09
Forum: ESP Easy: General Discussion
Topic: Simple switch issues
Replies: 4
Views: 1111

Simple switch issues

hi all, I'm trying to use a simple pushbutton to turn a LED on locally for testing purposes but having hard times achieving it. I have a LED connected to gpio 12 and a push button on pgio 16. I already tried a lot of combinations of the switch configuration but still struggling. (tried both bringing...
by hugo11
06 Jan 2017, 10:27
Forum: ESP Easy: Projects / Applications
Topic: Help on rules with domoticz
Replies: 6
Views: 3040

Re: Help on rules with domoticz

Hi Mijn.Handen, I have a similar setup than you but I'm fighting with the PIR. I would like to send a HTTP request from ESP when the PIR triggers, the issues I have: - There is a delay between triggering the PIR and ESP recognizing it - What is the configuration of the SWITCH in ESP for PIR ? Thanks...
by hugo11
11 Dec 2016, 16:16
Forum: ESP Easy: Software
Topic: RF 433 plugin for KAKU in the playground
Replies: 41
Views: 19547

Re: RF 433 plugin for KAKU in the playground

so tried it with an rxb12 off ebay, no luck.

Could someone recommend what receivers are supported?
by hugo11
11 Dec 2016, 15:50
Forum: ESP Easy: General Discussion
Topic: couldn't flash esp 07
Replies: 2
Views: 1086

Re: couldn't flash esp 07

I just flashed an ESP 07 today.

what I did
connected 3,3V to VCC and EN
grounded GND GPIO15 & GPIO00

flased the firmware with the provided flasher, make sure you have the correct port & flash size (1M for esp07).

hope it helps.
by hugo11
05 Dec 2016, 12:44
Forum: ESP Easy: Software
Topic: 7 Segment LCD Display
Replies: 2
Views: 1217

Re: 7 Segment LCD Display

+1
Would be useful.
by hugo11
29 Nov 2016, 21:48
Forum: ESP Easy: Software
Topic: RF 433 plugin for KAKU in the playground
Replies: 41
Views: 19547

Re: RF 433 plugin for KAKU in the playground

renearts wrote:Wow, this looks great. I'll have a try with a RXB6 receiver and sender kit I have.
If this works well I might be able to get rid of my homeduino :)
any luck with testing ?
by hugo11
12 Nov 2016, 18:18
Forum: ESP Easy: General Discussion
Topic: SSD1306 text size
Replies: 2
Views: 1053

SSD1306 text size

hello,

Is it possible to change the text size on SSD1306 somehow?


Thanks,
hugo.
by hugo11
09 Nov 2016, 20:49
Forum: ESP Easy: Hardware
Topic: New module from AI Thinker: ESP-12S
Replies: 4
Views: 4042

Re: New module from AI Thinker: ESP-12S

I agree - ordering a few more 12E/ F units for now.
by hugo11
08 Nov 2016, 21:18
Forum: ESP Easy: Projects / Applications
Topic: MH-Z14 / MH-Z19 CO2 sensor
Replies: 55
Views: 33106

Re: MH-Z14 / MH-Z19 CO2 sensor

hi guys,
feedback, just built the co2 sensor with mhz19. so far (2 days) working fine with the code from playground. I set the power to 3.6V and power both the sensor and esp from one supply. thanks a lot to the developers.
by hugo11
08 Nov 2016, 20:36
Forum: ESP Easy: Hardware
Topic: New module from AI Thinker: ESP-12S
Replies: 4
Views: 4042

Re: New module from AI Thinker: ESP-12S

hi,
anyone tested this module with this FW?
by hugo11
08 Nov 2016, 20:35
Forum: Introduce yourself
Topic: hello from Slovakia
Replies: 1
Views: 645

hello from Slovakia

hello,
I work in IT and IoT is my hobby. I appreciate the hard work of the community, thanks guys. So far 4 sensors are up running.