Search found 36 matches
- 09 Nov 2019, 11:25
- Forum: ESP Easy: Hardware
- Topic: Blitzwolf BW-SHP6
- Replies: 16
- Views: 30870
Re: Blitzwolf BW-SHP6
Eehm, how did you add a 4M Winbond to a 8285 which is as far as I know the chip of the Blitzwolf? Do you have something like a picture? Disassembly process: https://github.com/arendst/Tasmota/wiki/BlitzWolf-SHP6 Replacing memory process: 1. Remove old memory http://icebox.pl/esp/1.jpg Old memory: h...
- 16 Mar 2019, 09:24
- Forum: ESP Easy: Hardware
- Topic: Blitzwolf BW-SHP6
- Replies: 16
- Views: 30870
- 03 Mar 2019, 17:38
- Forum: ESP Easy: Hardware
- Topic: Blitzwolf BW-SHP6
- Replies: 16
- Views: 30870
Re: Blitzwolf BW-SHP6
I changed the flash from 1MB to 4 MB (Winbond)
I used a new flash for SonOFF (ESP_Easy_mega-20190301_hard_SONOFF_POW_4M.bin)
And it works
I used a new flash for SonOFF (ESP_Easy_mega-20190301_hard_SONOFF_POW_4M.bin)
And it works
- 05 Feb 2019, 18:23
- Forum: ESP Easy: Hardware
- Topic: Blitzwolf BW-SHP6
- Replies: 16
- Views: 30870
Re: Blitzwolf BW-SHP6
Something can move forward in this topic? Is there a chance for a dedicated ESP Easy firmware?
There is only the hard_SONOFF_POW version, but you need 4 mb of flash. BW-SHP6 has only 1 mb
Best Regards,
Robert
There is only the hard_SONOFF_POW version, but you need 4 mb of flash. BW-SHP6 has only 1 mb
Best Regards,
Robert
- 21 Aug 2018, 21:07
- Forum: ESP Easy: Software
- Topic: Relay recovery last state after power failure
- Replies: 3
- Views: 8899
Relay recovery last state after power failure
Hi,
How to read the status of relays from Domoticz during booting ESP Easy ? and set the relay in ESP Easy ?
Best Regards,
Robert
How to read the status of relays from Domoticz during booting ESP Easy ? and set the relay in ESP Easy ?
Best Regards,
Robert
- 08 Jul 2018, 11:16
- Forum: ESP Easy: General Discussion
- Topic: Number of Devices / Tasks limited to 12 ?
- Replies: 36
- Views: 30655
Re: Number of Devices / Tasks limited to 12 ?
Ok, in that case, use two wemos d1 mini.
- 08 Jul 2018, 09:40
- Forum: ESP Easy: General Discussion
- Topic: Number of Devices / Tasks limited to 12 ?
- Replies: 36
- Views: 30655
Re: Number of Devices / Tasks limited to 12 ?
Is it planned to extend the number of tasks?
If it can not be extended normally?
If it can not be extended normally?
- 07 Jul 2018, 21:25
- Forum: ESP Easy: General Discussion
- Topic: Number of Devices / Tasks limited to 12 ?
- Replies: 36
- Views: 30655
Re: Number of Devices / Tasks limited to 12 ?
Then you need to study the wiki and try to resolve the issue with self compile. We do not have the time to support self compilers, sorry. Okay, I read Arduino's instructions: https://www.letscontrolit.com/wiki/index.php/Tutorial_Arduino_Firmware_Upload What next do I need to do to change the range ...
- 07 Jul 2018, 21:15
- Forum: ESP Easy: General Discussion
- Topic: Number of Devices / Tasks limited to 12 ?
- Replies: 36
- Views: 30655
Re: Number of Devices / Tasks limited to 12 ?
I got a little lost in all this.
What do I have to do to extend from 12 to 15 devices?
Help, please.
Best Regards
Robert
What do I have to do to extend from 12 to 15 devices?
Help, please.
Best Regards
Robert
- 04 Jul 2018, 19:57
- Forum: ESP Easy: General Discussion
- Topic: Number of Devices / Tasks limited to 12 ?
- Replies: 36
- Views: 30655
Re: Number of Devices / Tasks limited to 12 ?
I have never used an IDE (PlatformIO or Arduino) but will adapt to the instructions.
I always flash a ready bin file.
Best Regards,
Robert
I always flash a ready bin file.
Best Regards,
Robert
- 04 Jul 2018, 13:44
- Forum: ESP Easy: General Discussion
- Topic: Number of Devices / Tasks limited to 12 ?
- Replies: 36
- Views: 30655
Re: Number of Devices / Tasks limited to 12 ?
can I ask for more details, I will do it for the first time I need to change from 12 to 15 tasks.
- 04 Jul 2018, 11:17
- Forum: ESP Easy: General Discussion
- Topic: Number of Devices / Tasks limited to 12 ?
- Replies: 36
- Views: 30655
Re: Number of Devices / Tasks limited to 12 ?
I tried to find the parameter in ESPEasy.ino:
#define TASKS_MAX 12 // max 12!"
but unfortunately I do not see it in the version ESPEasy_mega-20180625.
Please help.
Best Regards
Robert
#define TASKS_MAX 12 // max 12!"
but unfortunately I do not see it in the version ESPEasy_mega-20180625.
Please help.
Best Regards
Robert
- 26 Mar 2017, 19:14
- Forum: ESP Easy: Hardware
- Topic: Pulse Counter 3-pin fan PC
- Replies: 4
- Views: 4793
Pulse Counter 3-pin fan PC
Hi,
Will this solution work? Use a pulse counter to measure the speed of the PC fan:
Will this solution work? Use a pulse counter to measure the speed of the PC fan:
- 25 Mar 2017, 10:19
- Forum: ESP Easy: Hardware
- Topic: conecting to diode - check state
- Replies: 11
- Views: 8920
Re: conecting to diode - check state
It works (on GPIO 3), thank you
- 22 Mar 2017, 12:08
- Forum: ESP Easy: Software
- Topic: Switch rules
- Replies: 26
- Views: 23246
Re: Switch rules
I use toggle switch (on/off) for example:
- 20 Mar 2017, 23:07
- Forum: ESP Easy: Software
- Topic: Switch rules
- Replies: 26
- Views: 23246
Re: Switch rules
I'm sorry for my mistake
I use the physical bistable button/switch (press this button in this position)
I use the physical bistable button/switch (press this button in this position)
- 20 Mar 2017, 22:49
- Forum: ESP Easy: Hardware
- Topic: conecting to diode - check state
- Replies: 11
- Views: 8920
Re: conecting to diode - check state
if i may suggest anyways.... Replace the LED with an optocoupler. It separates the ESP from your circuit reliably and can be read with a standard GPIO input. Regards Shardan Can I ask for an example of an optocoupler that would be suitable for use in this case? Is the output needed for a control tr...
- 20 Mar 2017, 22:30
- Forum: ESP Easy: Software
- Topic: Switch rules
- Replies: 26
- Views: 23246
Re: Switch rules
I try as I can :) Domoticz allows remote control buttons with Easy ESP, commands, respectively: Amp / Speakers A On Action: http://192.168.3.120/control?cmd=GPIO,16,0 Off Action: http://192.168.3.120/control?cmd=GPIO,16,1 Amp / Speakers B On Action: http://192.168.3.120/control?cmd=GPIO,12,0 Off Act...
- 20 Mar 2017, 22:16
- Forum: ESP Easy: Hardware
- Topic: conecting to diode - check state
- Replies: 11
- Views: 8920
- 20 Mar 2017, 21:54
- Forum: ESP Easy: Hardware
- Topic: conecting to diode - check state
- Replies: 11
- Views: 8920
Re: conecting to diode - check state
Thanks for the response,
I decided to leave on the ADC, I did not use it for anything, and here it works fine (for 1,74V shows 1024):
I decided to leave on the ADC, I did not use it for anything, and here it works fine (for 1,74V shows 1024):
- 20 Mar 2017, 21:43
- Forum: ESP Easy: Software
- Topic: Switch rules
- Replies: 26
- Views: 23246
Re: Switch rules
I tested this version, but I only manage to turn on the relay, I can not turn it off.
- 20 Mar 2017, 17:14
- Forum: ESP Easy: Hardware
- Topic: conecting to diode - check state
- Replies: 11
- Views: 8920
Re: conecting to diode - check state
Problem solved i use ADC.
- 20 Mar 2017, 11:40
- Forum: ESP Easy: Hardware
- Topic: conecting to diode - check state
- Replies: 11
- Views: 8920
conecting to diode - check state
Hi,I would like to check the status LEDs on the "other system" (common ground) when it is turned on and when it is turned off. How to connect and configure? Voltage when it is switched on = 1,74 V Voltage when it is switched off = -0,60V (meter error?) I would like to plug in to GPIO09 or ...
- 20 Mar 2017, 11:33
- Forum: ESP Easy: Software
- Topic: Switch rules
- Replies: 26
- Views: 23246
- 19 Mar 2017, 15:53
- Forum: ESP Easy: Software
- Topic: Switch rules
- Replies: 26
- Views: 23246
Re: Switch rules
Rules based on your code: On SwitchA#switch do If [SpeakersA#state]=0 Gpio 16,1 Else Gpio 16,0 Endif Endon On SwitchB#switch do If [SpeakersB#state]=0 Gpio 12,1 Else Gpio 12,0 Endif Endon Configuration ESP Easy: http://icebox.pl/espeasy/espeasy_Diora1.png http://icebox.pl/espeasy/espeasy_Diora2.png ...
- 18 Mar 2017, 15:25
- Forum: ESP Easy: Software
- Topic: Switch rules
- Replies: 26
- Views: 23246
Re: Switch rules
I tested again, and unfortunately for me does not work
- 17 Mar 2017, 23:02
- Forum: ESP Easy: Software
- Topic: Switch rules
- Replies: 26
- Views: 23246
Re: Switch rules
But I have already tested this configuration and it does not work. Maybe something is wrong, tomorrow it will analyze ...
- 17 Mar 2017, 13:44
- Forum: ESP Easy: Software
- Topic: Switch rules
- Replies: 26
- Views: 23246
Re: Switch rules
I use bistable switch
- 17 Mar 2017, 08:56
- Forum: ESP Easy: Software
- Topic: Switch rules
- Replies: 26
- Views: 23246
Re: Switch rules
Your script (Rules) only works properly when you turn on the relay. It does not work turn off (another change of state the switch).
- 17 Mar 2017, 00:08
- Forum: ESP Easy: Software
- Topic: Switch rules
- Replies: 26
- Views: 23246
Re: Switch rules
I lost me at all, use remotely from domoticz and two physical buttons to control two relays. Can you give me the full code for Rules?
Thx
Robert
Thx
Robert
- 16 Mar 2017, 23:59
- Forum: ESP Easy: Software
- Topic: Switch rules
- Replies: 26
- Views: 23246
Re: Switch rules
I've tested, unfortunately, it does not work properly. He falls into a loop when, they try to turn off.
- 16 Mar 2017, 23:45
- Forum: ESP Easy: Software
- Topic: Switch rules
- Replies: 26
- Views: 23246
Re: Switch rules
I do not quite understand, my configuration:
GPIO-14 = SwitchA
GPIO-16 = RelayA
GPIO-13 = SwitchB
GPIO-12 = RelayB
GPIO-14 = SwitchA
GPIO-16 = RelayA
GPIO-13 = SwitchB
GPIO-12 = RelayB
- 16 Mar 2017, 22:56
- Forum: ESP Easy: Software
- Topic: Switch rules
- Replies: 26
- Views: 23246
Switch rules
Hi, I'm currently using this configuration: on SwitchAOn do gpio 16,0 inputswitchstate 14,1 endon on SwitchAOff do gpio 16,1 inputswitchstate 14,0 endon on SwitchBOn do gpio 12,0 inputswitchstate 13,1 endon on SwitchBOff do gpio 12,1 inputswitchstate 13,0 endon on SwitchA#switch do if [SwitchA#switc...
- 15 Mar 2017, 22:50
- Forum: ESP Easy: Hardware
- Topic: Problem with GPIO16 (D0) in ESP-12E
- Replies: 4
- Views: 10245
Re: Problem with GPIO16 (D0) in ESP-12E
Problem solved, small changes to the PCB:
GPIO-14 = Switch
GPIO-16 = Relay (only working out!)
GPIO-13 = SwitchB
GPIO-12 = RelayB
Best Regards
Robert
GPIO-14 = Switch
GPIO-16 = Relay (only working out!)
GPIO-13 = SwitchB
GPIO-12 = RelayB
Best Regards
Robert
- 14 Mar 2017, 22:18
- Forum: ESP Easy: Hardware
- Topic: Problem with GPIO16 (D0) in ESP-12E
- Replies: 4
- Views: 10245
Re: Problem with GPIO16 (D0) in ESP-12E
First check: Is the "Sleep Mode" box checked in the ESPEasy "config" tab? It should not be checked. Then check the "hardware" Tab, the GPIO16 (D0) should be set to "default". Yes, I checked is correctly (unchecked Sleep Mode, and GPIO16 (D0) is set to default...
- 12 Mar 2017, 14:12
- Forum: ESP Easy: Hardware
- Topic: Problem with GPIO16 (D0) in ESP-12E
- Replies: 4
- Views: 10245
Problem with GPIO16 (D0) in ESP-12E
Hi, I have a problem I connected the switch to GPIO14 1 and 2 to GPIO16. The first works fine, the second (GPIO16) physically works well, but ESP disconnects from the WiFi network, no access to the web interface, just restart helps. Everything works fine when the first button is pressed (GPIO14, Inv...