Search found 32 matches
- 02 Apr 2020, 14:27
- Forum: ESP Easy: Hardware
- Topic: New hackable ESP gadgets in local budget store "action" !!!
- Replies: 112
- Views: 280551
Re: New hackable ESP gadgets in local budget store "action" !!!
Hi all after a few months I decided to give this project another go. Now, I was struggling to get some information so I thought I'd leave my experiences here 1. All flashing was done by soldering the cables and adding the Tasmota firmware using Esptool 2. The idea of the rules is actually very simpl...
- 13 Jan 2020, 08:51
- Forum: ESP Easy: Hardware
- Topic: New hackable ESP gadgets in local budget store "action" !!!
- Replies: 112
- Views: 280551
Re: New hackable ESP gadgets in local budget store "action" !!!
Has anyone got the door sensor running on custom firmware? I have one running with SmartNodeRules. Just updated the plugin so it creates a rule event "TUYA#Event=<state>" when the sensor detects a change. Sample rule: On TUYA#Event do msgbus %sysname%/DoorSwitch=%eventvalue% endon Any of ...
- 13 Jan 2020, 08:46
- Forum: ESP Easy: Hardware
- Topic: New hackable ESP gadgets in local budget store "action" !!!
- Replies: 112
- Views: 280551
Re: New hackable ESP gadgets in local budget store "action" !!!
Hi ! Door sensor owner here :) I just connect the reed to GPIO13. 20190825_165123.jpg It works since 25/08 without battery replacement. @Neutrino a few questions: 1. Does the device go to deep sleep after a change is detected 2. Are you using stock firmware (espeasy/tasmota/?) to do the update? My ...
- 04 Jul 2018, 13:33
- Forum: ESP Easy: Hardware
- Topic: Sonoff relay status - domoticz Update
- Replies: 4
- Views: 4750
Re: Sonoff relay status - domoticz Update
Hey I have no idx set in my devices and only use the relay for a 2CH sonoff. What I do is in the rules send my status to domoticz over HTTP. SendToHTTP 192.168.xxx.xxx,8080,/json.htm?type=command¶m=switchlight&idx=64&switchcmd=Set%20Level&level=0 Maybe you can send the status als...
- 04 Jul 2018, 10:47
- Forum: ESP Easy: Hardware
- Topic: Sonoff relay status - domoticz Update
- Replies: 4
- Views: 4750
Re: Sonoff relay status - domoticz Update
is this a sonoff touch or a normal switch?
- 04 Jul 2018, 09:22
- Forum: ESP Easy: Hardware
- Topic: nodemcu on battery
- Replies: 27
- Views: 46223
Re: nodemcu on battery
Hi all, thinking of putting this to the next level. I have some solar panels that, when fully in sunlight, produce 5V. I do have a charger board like the one described above for the battery but as the sunlight drops, the battery is no longer charged. So I was wondering if I could do the following: S...
- 03 Jul 2018, 16:44
- Forum: ESP Easy: Hardware
- Topic: nodemcu on battery
- Replies: 27
- Views: 46223
Re: nodemcu on battery
Hi, I connected the polulu to the V3 in and with a full battery it now runs about 24 hours. I believe my battery is 4400mAh. Currently my NodeMCU wakes up every 10 minutes. Considering it is only working approx 3 minutes per hour, this is 540mA. This result is a bit more less than 9 hours. Is there...
- 03 Jul 2018, 16:43
- Forum: ESP Easy: Hardware
- Topic: nodemcu on battery
- Replies: 27
- Views: 46223
Re: nodemcu on battery
I just ordered some ESP-12E's so will give those a try. The Polulu is a step up down to 3.3 V and stops at 2.7 volt https://www.pololu.com/product/2122
- 03 Jul 2018, 16:16
- Forum: ESP Easy: Hardware
- Topic: nodemcu on battery
- Replies: 27
- Views: 46223
Re: nodemcu on battery
Hi, I connected the polulu to the V3 in and with a full battery it now runs about 24 hours. I believe my battery is 4400mAh. Currently my NodeMCU wakes up every 10 minutes. Considering it is only working approx 3 minutes per hour, this is 540mA. This result is a bit more less than 9 hours. Is there ...
- 30 Jun 2018, 09:59
- Forum: ESP Easy: Software
- Topic: Way for one device to quickly report on another being up/running?
- Replies: 2
- Views: 2512
Re: Way for one device to quickly report on another being up/running?
Hi My 2ct's: - connect a capacitor between the source power and the esp device - Make sure you have a diode between the original source and a capacitor, so when the power shuts off, the capacitor doesn't try to power the fan. - Measure the power before the diode on the source side and connect it (us...
- 29 Jun 2018, 16:32
- Forum: ESP Easy: Software
- Topic: _p216 - Simple RGB Strip Controller + RGW Switch with Selector in Domoticz
- Replies: 0
- Views: 2630
_p216 - Simple RGB Strip Controller + RGW Switch with Selector in Domoticz
Hi all after following the the online tutorial from http://www.twoenter.nl/blog/arduino-esp/rgb-ledstrip-espeasy-en-domoticz/ I noticed that _P142 no longer compiled and also that it was too much for what I need. Hence I started to design my own (based on the P142 plugin) and came up with a smaller ...
- 25 Jun 2018, 08:26
- Forum: ESP Easy: Hardware
- Topic: nodemcu on battery
- Replies: 27
- Views: 46223
Re: nodemcu on battery
hi TD-er I am running it in deep sleep.Was testing with 10 minutes sleep. When I measured it , when connecting to VIN (and not 3.3V) it uses about 180mA... I think the capacity of the batteries are 4400mAh. So roughly calculating, I am coming to about 22 cycles on 1 battery (or about 5 hours). In se...
- 24 Jun 2018, 17:48
- Forum: ESP Easy: Hardware
- Topic: nodemcu on battery
- Replies: 27
- Views: 46223
nodemcu on battery
Hi all I am trying to run an outside sensors. I am using a nodemcu with a home-brew shield with a DHT22. I have put 2 3.7V Lipo batteries in series (averaging to 6.XV) and connect this to VIN and Ground. Unfortunately, I noticed that the sensors is eating out the batteries very fast. I can only run ...
- 18 Jun 2018, 08:47
- Forum: ESP Easy: Software
- Topic: platformIO compile error
- Replies: 6
- Views: 7403
Re: platformIO compile error
unfortunately no joy on this...
- 18 Jun 2018, 08:39
- Forum: ESP Easy: Software
- Topic: Serial MCU controlled relay/switch
- Replies: 459
- Views: 1395196
Re: Serial MCU controlled relay/switch
sorry is this is a stupid question, but will your firmware work with the Sonoff T1 2Gang (similar to the dual?). I both 2 and want to be able to control them using ESPEasy and Domoticz. This plugin will not work with any Sonoff T1. According to Tasmota wiki: "When pushing a button, the touch c...
- 17 Jun 2018, 17:14
- Forum: ESP Easy: Software
- Topic: platformIO compile error
- Replies: 6
- Views: 7403
platformIO compile error
Hi all when I try to compile the mega branch using Atom I am getting the following error Compiling .pioenvs/normal_ESP8285_1024/src/ESPEasy.ino.cpp.o Linking .pioenvs/normal_ESP8285_1024/firmware.elf Checking size .pioenvs/normal_ESP8285_1024/firmware.elf Building .pioenvs/normal_ESP8285_1024/firmwa...
- 17 Jun 2018, 16:13
- Forum: ESP Easy: Software
- Topic: Serial MCU controlled relay/switch
- Replies: 459
- Views: 1395196
Re: Serial MCU controlled relay/switch
Hi all
sorry is this is a stupid question, but will your firmware work with the Sonoff T1 2Gang (similar to the dual?). I both 2 and want to be able to control them using ESPEasy and Domoticz.
Kind regards
Steve
sorry is this is a stupid question, but will your firmware work with the Sonoff T1 2Gang (similar to the dual?). I both 2 and want to be able to control them using ESPEasy and Domoticz.
Kind regards
Steve
- 17 Jun 2018, 14:32
- Forum: ESP Easy: Software
- Topic: Serial MCU controlled relay/switch
- Replies: 459
- Views: 1395196
Re: Serial MCU controlled relay/switch
and don't bother going any further, I just literally burned some of the traces... To be honest, crappy PCB .
Still have a Sonoff Touch 2-gang to go with
Kind regards
Steve
Still have a Sonoff Touch 2-gang to go with
Kind regards
Steve
- 17 Jun 2018, 14:15
- Forum: ESP Easy: General Discussion
- Topic: confusing on downloads
- Replies: 2
- Views: 2586
Re: confusing on downloads
hey
thanks for the info Will try the version2.0 for flashing the board I have ongoing in the other topic
Kind regards
Steve
thanks for the info Will try the version2.0 for flashing the board I have ongoing in the other topic
Kind regards
Steve
- 17 Jun 2018, 13:59
- Forum: ESP Easy: Software
- Topic: Serial MCU controlled relay/switch
- Replies: 459
- Views: 1395196
Re: Serial MCU controlled relay/switch
Heyhey Looking further : would I be able to use this to flash it? Looked at the above link, but don't have a 3.3 + GND on the print. Would I be able to solder on the chip https://docs.tuya.com/en/hardware/WiFi-module/wifi-e3s-module-mcu.html pin 16/15 and 12 for comms and 8 and 9 to put 3.3V on it? ...
- 17 Jun 2018, 13:21
- Forum: ESP Easy: Software
- Topic: Serial MCU controlled relay/switch
- Replies: 459
- Views: 1395196
Re: Serial MCU controlled relay/switch
Hi all, I just received a Jinvoo dual switch. I would like to install the ESP firmware yet I do not find any empty pin headers... Has anyone experience with flashing this device? Below are the pictures of the PCB board. 20180617_131709.jpg 20180617_131714.jpg In case someone already flashed it, whic...
- 17 Jun 2018, 12:38
- Forum: ESP Easy: General Discussion
- Topic: confusing on downloads
- Replies: 2
- Views: 2586
confusing on downloads
Hi all am I the only one that gets lost in the amount of downloads on GitHub? I wanted to download the releases and ended up with downloading the mega-(date stamp)- version thinking this is the last release. When I flashed my Sonoff Touch T1, I ended up with a device doing nothing. Eventually I brow...
- 06 Feb 2018, 19:43
- Forum: ESP Easy: Software
- Topic: Nagios passive check support
- Replies: 3
- Views: 3501
Re: Nagios passive check support
Haven't tried it yet as still fiddling with switched, but would this not we a way to go?
http://www.usr-local.org/wiki/doku.php/ ... ive_checks
This way you could make a rule to send the update?
http://www.usr-local.org/wiki/doku.php/ ... ive_checks
This way you could make a rule to send the update?
- 06 Feb 2018, 19:26
- Forum: ESP Easy: Projects / Applications
- Topic: Updated : how to reboot a sonoff touch after installation?
- Replies: 1
- Views: 5948
Updated : how to reboot a sonoff touch after installation?
Hi all, I have installed sonoff Touch T1 and have the following. The UDP syslog component is working, but the http webinterface is not. I can also not ping to the device. It is currently wired to the N+L so it has 240V on it. 1. Is there a different way to reboot the esp without opening up the whole...
- 01 Feb 2018, 14:56
- Forum: ESP Easy: Projects / Applications
- Topic: using a sonoff T1 2 Gang as a simple controller
- Replies: 2
- Views: 3477
Re: using a sonoff T1 2 Gang as a simple controller
hey
so the Sonoff dual send the trigger to the sonoff light 1 and that send an update to domoticz? Ok, hadn't thought of that Thanks for the pointer
Kind regards
Steve
so the Sonoff dual send the trigger to the sonoff light 1 and that send an update to domoticz? Ok, hadn't thought of that Thanks for the pointer
Kind regards
Steve
- 31 Jan 2018, 14:46
- Forum: ESP Easy: Projects / Applications
- Topic: using a sonoff T1 2 Gang as a simple controller
- Replies: 2
- Views: 3477
using a sonoff T1 2 Gang as a simple controller
Hi all,
quick Q: I have set up 2 Sonoff Touch 1 gang wireless switches for my lighting. Now I wanted to know if I could use a 2 gang switch as a simple dummy? Basically I want it to send a trigger to domoticz and then let domoticz turn on Light 1 or 2. Any done this before?
Kind regards
Steve
quick Q: I have set up 2 Sonoff Touch 1 gang wireless switches for my lighting. Now I wanted to know if I could use a 2 gang switch as a simple dummy? Basically I want it to send a trigger to domoticz and then let domoticz turn on Light 1 or 2. Any done this before?
Kind regards
Steve
- 22 Jan 2018, 16:27
- Forum: ESP Easy: Hardware
- Topic: Yewelink/Tuya WiFi Touch wall light switch
- Replies: 43
- Views: 652884
Re: Yewelink/Tuya WiFi Touch wall light switch
Heyhey
can you confirm that this EU version works? I would like to set up these as simple "dummy" switches (basically set the switch for another Sonoff switch)
Kind regards
Steve
can you confirm that this EU version works? I would like to set up these as simple "dummy" switches (basically set the switch for another Sonoff switch)
Kind regards
Steve
- 15 Aug 2017, 13:13
- Forum: ESP Easy: General Discussion
- Topic: sonoff dual flashing the ESP
- Replies: 68
- Views: 97184
Re: sonoff dual flashing the ESP
Hi Bryan I am in a similar situation as above. I am working on a blinds controller, not using any devices, simply your Sonoff nomenclature. Using GPIO does not work. Using Sonoff works, but ... sometimes although the log show that the timers are running and the Sonoff switch are switched, nothing ha...
- 08 Aug 2017, 20:38
- Forum: ESP Easy: General Discussion
- Topic: sonoff dual flashing the ESP
- Replies: 68
- Views: 97184
Re: sonoff dual flashing the ESP
Just to let you know : It works. Just pay attention when connecting the 220V to it while running. Don't ask me what component I touched, but got zapped twice
- 08 Aug 2017, 15:17
- Forum: ESP Easy: General Discussion
- Topic: sonoff dual flashing the ESP
- Replies: 68
- Views: 97184
Re: sonoff dual flashing the ESP
Hey Bryan,
just tried it but sitting remote, so cannot see the result. From the log file this does seem to work.
Just another stupid Q: which GPIO's are the additional button 1 and button 2?
Kind regards
Steve
just tried it but sitting remote, so cannot see the result. From the log file this does seem to work.
Just another stupid Q: which GPIO's are the additional button 1 and button 2?
Kind regards
Steve
- 07 Aug 2017, 11:25
- Forum: ESP Easy: General Discussion
- Topic: sonoff dual flashing the ESP
- Replies: 68
- Views: 97184
Re: sonoff dual flashing the ESP
Hi LisaM,
I am already using global sync, but all my sensors and controllers are not DHCP and sit in a different IP range. I can set a static IP on the other Espeasy's so was wondering if this is due to this?
Anyone who can tell me how to use the sonoff1 / sonoff2 in rules?
Kind regards
Steve
I am already using global sync, but all my sensors and controllers are not DHCP and sit in a different IP range. I can set a static IP on the other Espeasy's so was wondering if this is due to this?
Anyone who can tell me how to use the sonoff1 / sonoff2 in rules?
Kind regards
Steve
- 06 Aug 2017, 14:54
- Forum: ESP Easy: General Discussion
- Topic: sonoff dual flashing the ESP
- Replies: 68
- Views: 97184
Re: sonoff dual flashing the ESP
Hi all maybe a stupid Q, but can I use the sonoff1 id in the rules? I want to make sure that I shut off sonoff1 when enabling sonoff 2 (using this to turn my blinds up and down.) Also, don't know if this is due to the firmware, but setting a static IP, locks the sonoff and I need to reflash it. Kind...