Search found 404 matches

by enesbcs
15 Sep 2019, 15:35
Forum: ESP Easy: Hardware
Topic: New ESP gadget
Replies: 323
Views: 140328

Re: New ESP gadget

tim wrote:
15 Sep 2019, 15:25
Does ESP Easy support the display?
The display is an SPI connected ST7789V so i guess not.
by enesbcs
13 Sep 2019, 17:39
Forum: ESP Easy: Hardware
Topic: New ESP gadget
Replies: 323
Views: 140328

Re: New ESP gadget

by enesbcs
12 Sep 2019, 17:52
Forum: Experimental
Topic: Arduino Easy 2560
Replies: 130
Views: 33745

Re: Arduino Easy 2560

Reefie wrote:
12 Sep 2019, 12:16
What software did you use to flash it, I cannot find the board in the Arduino IDE?
You have to install "Arduino SAM boards (Cortex-M3)" and this core also:
https://github.com/rogerclarkmelbourne/arduino_stm32
by enesbcs
11 Sep 2019, 18:08
Forum: ESP Easy: Projects / Applications
Topic: Sleeptime
Replies: 24
Views: 3133

Re: Sleeptime

ESP-now is a protocol specific for ESP nodes. It is something I plan to add later, since it does allow for really short WiFi on times. In short, you can send data from one node to another one (only a limited set of MAC addresses can be "paired" for this) It is using the WiFi radio, but does not nee...
by enesbcs
07 Sep 2019, 16:55
Forum: ESP Easy: Hardware
Topic: New hackable ESP gadgets in local budget store "action" !!!
Replies: 29
Views: 5302

Re: New hackable ESP gadgets in local budget store "action" !!!

AFAIK, the door sensor has no GPIO attached to any hardware. Only RX/TX is connected to the other MCU. I'm working on a serial plugin for ESPCoreRules to read the status from the other MCU and instruct it to power off again. I have seen an existing plugin for ESP Easy to controll Tuya MCU that migh...
by enesbcs
05 Sep 2019, 17:42
Forum: ESP Easy: Projects / Applications
Topic: ESP8266 multisensor
Replies: 9
Views: 967

Re: ESP8266 multisensor

I have ordered another smaller night light too. Challange will be to fit everything in the case but it has mains power. https://www.aliexpress.com/item/33045547622.html?spm=a2g0s.13010208.0.0.576fcscscscsqw&gps-id=pay_success&scm=1007.13409.84631.0&scm_id=1007.13409.84631.0&scm-url=1007.13409.84631...
by enesbcs
31 Aug 2019, 20:22
Forum: ESP Easy: General Discussion
Topic: lc technology ESP8266 realy x4 Problem
Replies: 8
Views: 841

Re: lc technology ESP8266 realy x4 Problem

epost wrote:
31 Aug 2019, 11:46
I think it's a NUVOTON 8 bit 8051 compatible microcontroller
It is a standard 4 channel Serial MCU controlled relay/switch, can be used with ESPEasy and P165 plugin. (If the NUVOTON has its standard program)
viewtopic.php?f=6&t=3245
by enesbcs
31 Aug 2019, 17:37
Forum: ESP Easy: Projects / Applications
Topic: ESP8266 multisensor
Replies: 9
Views: 967

Re: ESP8266 multisensor

Did you shield the radar module? Otherwise it is also detecting people at the other side of the wall you mount this to. Nope, however i planned to use some tin foil beneath it, but eventually it is not needed. (at least for me) Motion sensor is combined, so if the radar sensor is seeing from the ot...
by enesbcs
25 Aug 2019, 22:25
Forum: ESP Easy: Software
Topic: Standalone mode
Replies: 18
Views: 1165

Re: Standalone mode

So the Ali link https://www.aliexpress.com/item/1876368739.html?src=google&albslr=220833420&src=google&albch=shopping&acnt=494-037-6276&isdl=y&slnk=&plac=&mtctp=&albbt=Google_7_shopping&aff_platform=google&aff_short_key=UneMJZVf&&albagn=888888&albcp=1706100219&albag=73428776544&trgt=539263010115&cr...
by enesbcs
25 Aug 2019, 22:15
Forum: Experimental
Topic: Arduino Easy 2560
Replies: 130
Views: 33745

Re: Arduino Easy 2560

I am interested to follow this as I would like to have Ethernet connection. Could you let me know the pins to connect a w5500 to the stm32f103rct6 board please Yes of course, the wiring is the following: RCT6 W5500 --------------------- 3.3V 3.3V GND GND RST RST A4 SCS A5 SCLK A6 MISO A7 MOSI https...
by enesbcs
25 Aug 2019, 08:49
Forum: ESP Easy: Software
Topic: Standalone mode
Replies: 18
Views: 1165

Re: Standalone mode

To answer the last question first, nope not yet. And about the clock issue. One thing that will work for sure, is using a GPS module. I don't know if there is a RTC module supported. (so assume it isn't) If somebody implements plugin callable "settime()" function into ESPEasy core and time related ...
by enesbcs
20 Aug 2019, 09:05
Forum: ESP Easy: Hardware
Topic: extra IO with PIR or distance snsor
Replies: 7
Views: 2313

Re: extra IO with PIR or distance snsor

- How do I monitor a PCF port ? What I tried below does not work? Why do not you create separeted tasks for every function? See wiki: https://www.letscontrolit.com/wiki/index.php/PCF8574 - Is it possible to use the PCF8574 for inputs (door + pir) and output (relays) If you create a task that will b...
by enesbcs
19 Aug 2019, 10:51
Forum: ESP Easy: General Discussion
Topic: RPIEasy
Replies: 146
Views: 13391

Re: RPIEasy

I've published some basic RPIEasy usage manual at instructables:
https://www.instructables.com/id/RPIEas ... or-Device/
by enesbcs
19 Aug 2019, 07:05
Forum: ESP Easy: Hardware
Topic: SERIAL MCU
Replies: 1
Views: 1013

Re: SERIAL MCU

Hi, I use an ESP01 to control two relays. The version of espeasy is 2.4.0.C.2. To control this relay i use "Serial MCU controlled switch". But for a good communication i want to use a Wemos D1 with external antenna. I use the version MEGA-20190626 but i don't find the good switch to control my rela...
by enesbcs
15 Aug 2019, 17:43
Forum: ESP Easy: General Discussion
Topic: RPIEasy
Replies: 146
Views: 13391

Re: RPIEasy

Hi Enesbcs, looking at the plugins implemented in rpieasy I found one that looks very promising for me. It is about plugin P511 - Run OS command. My question is: with this command it is possible to run/stop any executable script even it is not a python3 script? Can be used in rules ? Please give me...
by enesbcs
07 Aug 2019, 07:04
Forum: ESP Easy: General Discussion
Topic: RPIEasy
Replies: 146
Views: 13391

Re: RPIEasy

Hi Enesbcs, regarding infrared plugin I want to tell you that am using with success in other python application pigpio library and according with the documentation it is also capable to be an alternative to lirc for transmitting and receiving IR codes. You can check this link : https://raspberrypi....
by enesbcs
05 Aug 2019, 19:33
Forum: Experimental
Topic: Arduino Easy 2560
Replies: 130
Views: 33745

Re: Arduino Easy 2560

Bigbrother STM32F103RCT6 in action: https://m.blog.hu/bi/bitekmindenhol/image/rct_example.jpg 182kb STM32-ArduinoEasy firmware Controllers included: Domoticz HTTP, Domoticz MQTT, OpenHAB MQTT Plugins included: Switch, ADC, Pulse, Dallas, DHT, BH1750, SI7021, OLED (experimental), Sysinfo, BMP280/BME2...
by enesbcs
03 Aug 2019, 21:10
Forum: ESP Easy: Software
Topic: Serial MCU controlled relay/switch
Replies: 301
Views: 77099

Re: Serial MCU controlled relay/switch

Can you give me an example? Examples given at the first post https://www.letscontrolit.com/forum/viewtopic.php?p=16998#p16998 The following command switches the second relay on the panel, if it has a second relay and you set the correct number of relays on the plugin settings page: relay,1,1 The fo...
by enesbcs
03 Aug 2019, 16:45
Forum: ESP Easy: Software
Topic: Serial MCU controlled relay/switch
Replies: 301
Views: 77099

Re: Serial MCU controlled relay/switch

fiets wrote:
03 Aug 2019, 16:37
TaskValueSet 1,1,1 //set Var#State to 1
I do not really understand what do you wan to achieve with taskvalueset? This plugin works with relay command, see the first post in this thread...
by enesbcs
30 Jul 2019, 20:23
Forum: ESP Easy: General Discussion
Topic: RPIEasy
Replies: 146
Views: 13391

Re: RPIEasy

Hi Enesbcs, I am using RPIEasy for some time and it is a great piece of software. When do you think that will be possible for you to implement in RPIeasy ToniA infrared plugin for controlling air conditioning units(I think is HeatpumpIR plugin)? Thank you Hi, I am very sorry, but as i wrote earlier...
by enesbcs
29 Jul 2019, 22:49
Forum: ESP Easy: Software
Topic: Serial MCU controlled relay/switch
Replies: 301
Views: 77099

Re: Serial MCU controlled relay/switch

I dont know, just copied the \nOK part from another ESPEasy plugin, i assumed if that works there, it will be ok here also.. I tried the last PUYA safe bin file, but it was lacking the OpenHAB MQTT Controller option, so my existing configuration didn't work. Would it be possible to include OpenHAB ...
by enesbcs
20 Jul 2019, 20:03
Forum: ESP Easy: Projects / Applications
Topic: ESP8266 Thermostat
Replies: 17
Views: 4689

Re: ESP8266 Thermostat

hello, can someone explain to me how I can change so that after a while the display turns off and after pressing a key it wakes up for a while? I can't always leave it on and I can't find a way to turn it off, if I interrupt the current to oled then not seen read until restart If you are using P168...
by enesbcs
20 Jul 2019, 19:54
Forum: ESP Easy: Software
Topic: Serial MCU controlled relay/switch
Replies: 301
Views: 77099

Re: Serial MCU controlled relay/switch

Which one should I try and are they PUYA safe? Oops, attached a new one. This is my first time bringing ESPEasy into my projects and to me, it just seemed out of place, to see a response in MQTT with leading \n character, while observing using MQTT Explorer. Is there a reason why the plugin must in...
by enesbcs
19 Jul 2019, 17:09
Forum: ESP Easy: Software
Topic: Serial MCU controlled relay/switch
Replies: 301
Views: 77099

Re: Serial MCU controlled relay/switch

issue 1: I'm running into some problems with the firmware on both modules, and it seems that both are unable to recover gracefully when it is forced to reconnect to the Wireless Access Point, or when the MQTT server restarted. I can verify this after, by connecting to http. On the Main page, the IP...
by enesbcs
19 Jul 2019, 07:06
Forum: ESP Easy: Software
Topic: Serial MCU controlled relay/switch
Replies: 301
Views: 77099

Re: Serial MCU controlled relay/switch

I've tried ESPEasy_R147_1M_64kS.bin and ESPEasy_1M_128kSPIFFS_PUYA.bin, everything is configured well (I think) but when I go to http://<lctechip>/control?cmd=relay,0,1 http://<lctechip>/control?cmd=relay,1,1 Relays are not activated whereas I can see their state changing in the GUI (Device page). ...
by enesbcs
18 Jul 2019, 21:13
Forum: ESP Easy: General Discussion
Topic: How to use Modem Sleep
Replies: 20
Views: 1637

Re: How to use Modem Sleep

spicer wrote:
18 Jul 2019, 20:51
I have testet with 2018 sources. ....not work :roll:
Try that
by enesbcs
18 Jul 2019, 20:47
Forum: ESP Easy: General Discussion
Topic: How to use Modem Sleep
Replies: 20
Views: 1637

Re: How to use Modem Sleep

No chance. I copy the content of lib to libraries, and src renamed to ESPEasy. I make no modifications. Compile and upload works. But the board is not working. Does anyone have a hint? You are using the new core >2.5 which i do not use. This is the main difference. I am still using core 2.4.2 for c...
by enesbcs
18 Jul 2019, 20:44
Forum: ESP Easy: Hardware
Topic: extra IO with PIR or distance snsor
Replies: 7
Views: 2313

Re: extra IO with PIR or distance snsor

Hello to all, Is it possible to use an IO extension (Via i2c) and connect to it distance sensors or PIRs ? I would like to automate my garage door and might be short on IOs for my requirement: - 2 distance sensors (2 IO each) - 1 PIR would be great (an other IO) - 2 relays (those will be on an IO e...
by enesbcs
17 Jul 2019, 22:10
Forum: ESP Easy: General Discussion
Topic: How to use Modem Sleep
Replies: 20
Views: 1637

Re: How to use Modem Sleep

spicer wrote:
17 Jul 2019, 22:02
Why the direct input modemsleep,1 is "Unknown command!" ?
Maybe you do not added the plugin to the device list.
by enesbcs
17 Jul 2019, 21:43
Forum: ESP Easy: General Discussion
Topic: How to use Modem Sleep
Replies: 20
Views: 1637

Re: How to use Modem Sleep

This works not for me :( I compile/upload ESPEasy_mega-20190630 with sketch _P166_WiFiMan.ino. I use Arduino IDE and the tutorial from https://waschto.eu/espeasy-eigene-oder-zusaetzliche-plugins-einbinden/#top After uploading, the ESP8266 (nodeMCU V3) is death. Do you have a step by step tutorial f...
by enesbcs
15 Jul 2019, 18:18
Forum: Experimental
Topic: Arduino Easy 2560
Replies: 130
Views: 33745

Re: Arduino Easy 2560

You are right it is expensive if you buy board.B ut he replaced the chip directly on STM32 (blue pill ) with GD32 chip.But is it worth the effort ? may be not.He shows software part in his video between 23 & 28 minutes mark.Basically he used Naze32 bootloader to make it work. Thanks Altough this GD...
by enesbcs
14 Jul 2019, 23:01
Forum: Experimental
Topic: Arduino Easy 2560
Replies: 130
Views: 33745

Re: Arduino Easy 2560

Datasheet for GD32F103RCT6 : Lot better than STM32 at the almost same price. GD32F103RCT6 seems nice, but i've only found a Development board with it for 13USD which is almost double than the 7USD STM32F103RCT6 board.. And i did not found any detailed description about how to compile and with which...
by enesbcs
09 Jul 2019, 19:27
Forum: Experimental
Topic: Arduino Easy 2560
Replies: 130
Views: 33745

Re: Arduino Easy 2560

I've succesfully compiled it to a Maple Mini and it is running fine:
Image
Wiring:
Image
ArduinoEasy for STM32:
Image
by enesbcs
30 Jun 2019, 19:30
Forum: ESP Easy: Software
Topic: Serial MCU controlled relay/switch
Replies: 301
Views: 77099

Re: Serial MCU controlled relay/switch

If anybody know, how can I add this switches to home assistant? If you are adding an "OpenHAB MQTT" controller with the proper IP and port settings, and with the default Controller Subscribe /%sysname%/# ,and your unit name is for example "lctech2x": Than you can send MQTT messages to set 1st relay...
by enesbcs
29 Jun 2019, 19:50
Forum: ESP Easy: Software
Topic: Serial MCU controlled relay/switch
Replies: 301
Views: 77099

Re: Serial MCU controlled relay/switch

kallipso.v@gmail.com wrote:
29 Jun 2019, 12:11
HI
did you find a solution for it? I have the same problem
Farrukh wrote previously that when the red led is on, than the unit is working. (there are buttons on the unit, press them until the led color changes)
by enesbcs
18 Jun 2019, 17:51
Forum: ESP Easy: General Discussion
Topic: Switch Button Long Push
Replies: 16
Views: 2791

Re: Switch Button Long Push

Just wanted to say thanks for this. I've been using the plugin for ~ 6 months now :-) I also wrote a blog post about how to use it as well :-) https://techlife.nz/blog/create-an-esp8266-push-button-amazon-dash-clone-using-espeasy/ Thanks for mentioning. :) In fact, the new P001_Switch plugin in ESP...
by enesbcs
10 Jun 2019, 15:14
Forum: Experimental
Topic: Arduino Easy 2560
Replies: 130
Views: 33745

Re: Arduino Easy 2560

https://github.com/enesbcs/ArduinoEasy Used STM32 Arduino core is: https://github.com/rogerclarkmelbourne/Arduino_STM32 I like those type of "experiment" :) can you please share some info about your hardware (which dev board and most important which ETH module you used)? godo job!!! Thank you! The ...
by enesbcs
09 Jun 2019, 09:20
Forum: Experimental
Topic: Arduino Easy 2560
Replies: 130
Views: 33745

Re: Arduino Easy 2560

I decided to patch ArduinoEasy to run on my STM32F103RCT6 Development Board + W5500 Ethernet network module combination ($6.5 + $3) instead of the default Arduino Mega 2560 + Arduino Ethernet Shield. I think it is done, at least it compiles and run on my hardware. :) Do not expect much support or de...
by enesbcs
31 May 2019, 21:20
Forum: ESP Easy: Software
Topic: Serial MCU controlled relay/switch
Replies: 301
Views: 77099

Re: Serial MCU controlled relay/switch

Thanks enesbcs! I tested it on the 2-channel switch relays I bought at first. As long as you get the board in the right mode (red led instead of blue) by pressing S2 at powerup the first time it works like a clock now with "IPD preamble" checked !!! Big thanks! Although I now have a lot of automati...
by enesbcs
30 May 2019, 20:57
Forum: ESP Easy: Software
Topic: Serial MCU controlled relay/switch
Replies: 301
Views: 77099

Re: Serial MCU controlled relay/switch

If the start of the command packet is always ""0D 0A 2B 49 50 44 2C 30 2C 34 3A" i can integrate it to the plugin through a selectable checkbox like "Send IPD command always" THAT would be a big favour enesbcs!!! :) :) :) It seems like there are two communication versions out there. LC Tech origina...
by enesbcs
30 May 2019, 07:11
Forum: ESP Easy: Software
Topic: Serial MCU controlled relay/switch
Replies: 301
Views: 77099

Re: Serial MCU controlled relay/switch

It appears as if the esp module is not driving the relays on board, even though the esp module is subscribed/publishing MQTT messages properly. Maybe you are experiencing the same problem i had, see https://www.letscontrolit.com/forum/viewtopic.php?p=36707#p36707 . I checked with the original code ...
by enesbcs
29 May 2019, 17:47
Forum: ESP Easy: Software
Topic: Serial MCU controlled relay/switch
Replies: 301
Views: 77099

Re: Serial MCU controlled relay/switch

... It appears as if the esp module is not driving the relays on board, even though the esp module is subscribed/publishing MQTT messages properly. Please make sure that: - at ESPEasy Tools-Advanced settings Serial is enabled but serial logging is disabled (level 0) - the correct LCTECH relay type ...
by enesbcs
28 May 2019, 18:33
Forum: ESP Easy: Software
Topic: Serial MCU controlled relay/switch
Replies: 301
Views: 77099

Re: Serial MCU controlled relay/switch

Farrukh wrote:
28 May 2019, 17:39
... changing the relay states on the http page, but the actual relays on the LC Tech board are not changing states.
Old firmware version, wrong type selected in plugin, weak power supply, not correctly soldered relays on panel?
viewtopic.php?p=34341#p34341
by enesbcs
28 May 2019, 17:29
Forum: ESP Easy: General Discussion
Topic: RPIEasy
Replies: 146
Views: 13391

Re: RPIEasy

Hi! I already use ESPEasy and found your project today. I must say: great work! That's a thing for a Raspberry Pi I was long looking for. Really nice idea :) But let me ask one question: do you plan to support FHEM as a controller? Or is MQTT the only way for now and near future? Best regards Thank...
by enesbcs
27 May 2019, 17:08
Forum: ESP Easy: General Discussion
Topic: RPIEasy
Replies: 146
Views: 13391

Re: RPIEasy

bennybubble wrote:
27 May 2019, 12:31
It would be great if this could be implemented, can't you use edge-based-interrupt for counting (https://parg.co/hbz) ?
I'm more then happy to test it if needed !
-ben
https://github.com/enesbcs/rpieasy/issues/65
by enesbcs
24 May 2019, 21:37
Forum: ESP Easy: General Discussion
Topic: RPIEasy
Replies: 146
Views: 13391

Re: RPIEasy

bennybubble wrote:
24 May 2019, 19:50
What is the defintion of real-time?
In my case I want to count pulses from my gas- and energymeter, puls rate would be less then 1 Hz ...
I don't think this would be an issue with Python running on RPI/Raspbian.
-ben
Yes one per second can be achieved if it is enough.
by enesbcs
24 May 2019, 19:09
Forum: ESP Easy: General Discussion
Topic: RPIEasy
Replies: 146
Views: 13391

Re: RPIEasy

Hi, I really like the RPIeasy initiative, same look and feel as the originial ESPeasy ! To get more I/O, I'm replacing an 8266 with a RPI but now I'm almost there, I see there is no Generic - Puls Counter plugin. Are there plans to make such a plugin ? -ben I am not sure if real-time pulse counting...
by enesbcs
18 May 2019, 21:34
Forum: ESP Easy: Software
Topic: Serial MCU controlled relay/switch
Replies: 301
Views: 77099

Re: Serial MCU controlled relay/switch

Is there any reason that this doesn't work with an LCTECH relay on the latest firmware ESP82xx Core 2_4_2, NONOS SDK 2.2.1(cfd48f3), LWIP: 2.0.3 PUYA support It works fine on an older version "Core Version: 2_4_0_RC2" As far as I can see all the settings are the same, compiled on PlatformIO Thanks....
by enesbcs
15 May 2019, 22:44
Forum: uPyEasy: Software
Topic: python script to issue GPIO command
Replies: 2
Views: 324

Re: python script to issue GPIO command

I want to implement this command in Python from my RPI. If you want to control your Raspberry with ESPEasy-like commands why don't you simply use RPIEasy? (with ESPEasy P2P networking it is able to use udp SendTo commands for remote espeasy control for example..) https://www.letscontrolit.com/forum...