Search found 11 matches
- 30 Dec 2017, 15:11
- Forum: uPyEasy: Hardware
- Topic: ESP32 boards
- Replies: 277
- Views: 472250
Re: ESP32 boards
After installing Python I keep getting this error: import serial ImportError: No module named serial Did some research... Installed pyserial..... Same message Have tried to reinstall pyserial several times and keep getting the message that it's already installed. Also rebooted with no change. I am ...
- 30 Dec 2017, 02:17
- Forum: uPyEasy: Hardware
- Topic: ESP32 boards
- Replies: 277
- Views: 472250
Re: ESP32 boards
I hate to be "that guy" :roll: but would you happen to have a windows flashing howto laying around anywhere? I'm not having much luck here.... :mrgreen: Windows? The esp-tool is the same, since it's python... ;) Install python on your windows pc, replace '/dev/ttyUSBx' with comX and you'r...
- 29 Dec 2017, 16:13
- Forum: uPyEasy: Hardware
- Topic: ESP32 boards
- Replies: 277
- Views: 472250
Re: ESP32 boards
Hi Andrew, I've upgraded the wstest program to upyeasy_wifi_test program, it's source code is attached. Also the firmware in post 1 is upgraded. Can you flash that version and after the error run: import upyeasy_wifi_test Cheers, Lisa Working: The 12/29 version boots fine. It connects to WiFi. NTP ...
- 29 Dec 2017, 00:14
- Forum: uPyEasy: Hardware
- Topic: ESP32 boards
- Replies: 277
- Views: 472250
Re: ESP32 boards
Also, I tried testing the switch plugin with no success (still running the 2MB firmware). I tried GPIO12 and GPIO4 and they're never read. Nothing is output in the logs after I pull them to GND. I made sure I changed the delay to 10 seconds. I also tried setting them up as inputs on the Hardware tab...
- 29 Dec 2017, 00:01
- Forum: uPyEasy: Hardware
- Topic: ESP32 boards
- Replies: 277
- Views: 472250
Re: ESP32 boards
Is the normal 4MB firmware from the first post also working? MQTT should be working, at least Domoticz MQTT, are the settings correct (should the same as in ESPEasy). Is Domoticz HTTP working? Which plugin are you using? No. 4MB firmware is not working. I was getting bootloops like in post #4. For ...
- 28 Dec 2017, 22:34
- Forum: uPyEasy: Hardware
- Topic: ESP32 boards
- Replies: 277
- Views: 472250
Re: ESP32 boards
This is great! I'm able to run your special 2MB firmware on a doit.am v1 devkit ($7 on aliexpress).
So far, it's very encouraging. Please keep it up and let me know if I can help in any way.
BTW, is MQTT supposed to work? I tried pointing it at my MQTT server but there is no activity.
So far, it's very encouraging. Please keep it up and let me know if I can help in any way.
BTW, is MQTT supposed to work? I tried pointing it at my MQTT server but there is no activity.
- 24 Nov 2017, 16:50
- Forum: ESP Easy: Projects / Applications
- Topic: short and long press button mqtt
- Replies: 8
- Views: 7725
Re: short and long press button mqtt
This rule example in the wiki is from me and works like a charm. You don't have to wait 1 sec for an action. Switch delay is normally 0 and remove your delay of 300! @grovkillen: It should make no difference if you type 'timerSet,1,1' or 'timerSet 1 1'. Check out 'GPIO,12,1' and 'GPIO 12 1'. Both s...
- 22 Nov 2017, 23:18
- Forum: ESP Easy: Projects / Applications
- Topic: short and long press button mqtt
- Replies: 8
- Views: 7725
Re: short and long press button mqtt
I was hoping to do something like the code below instead (wanted to avoid having to wait 1 second for the first action to fire), but it doesn't work. Action1 is never triggered. Any idea how to work around this? on Button#State=1 do delay,300 if [Button#State]=0 //Action1 if button is short pressed ...
- 13 Nov 2017, 04:15
- Forum: ESP Easy: General Discussion
- Topic: ESPEasy v2.0.0-dev12 released
- Replies: 44
- Views: 47776
Re: ESPEasy v2.0.0-dev12 released
I'm getting the "Error while reading/writing config.dat in 926" with just: on onoff#push=1 do if [relay#Switch]=1 gpio,12,0 else gpio,12,1 endif endon Same here. Getting ""Error while reading/writing config.dat" for every rule that has an if statement. I'm running a bunch f...
- 09 Nov 2017, 15:52
- Forum: ESP Easy: Software
- Topic: New Plugin for LIS3DH Accelerometer
- Replies: 3
- Views: 3766
Re: New Plugin for LIS3DH Accelerometer
I have a few light switches that use cap sense but the touch area is small which requires some precision to toggle the switch. With LIS3DH glued to a "blank" wall plate I can hit it anywhere and it toggles. It's a bit faster and requires less precision. Have you been able to create a large...
- 09 Nov 2017, 03:04
- Forum: ESP Easy: Software
- Topic: New Plugin for LIS3DH Accelerometer
- Replies: 3
- Views: 3766
New Plugin for LIS3DH Accelerometer
For anyone interested, I implemented a plugin for the LIS3DH accelerometer. You can buy one for a few bucks on ebay. More information about a breakout board here: https://learn.adafruit.com/adafruit-lis3dh-triple-axis-accelerometer-breakout/wiring-and-test You can pick up the files from my github he...