@Thomas,
no its an old one with ESP8266.

btw with Periodical send Gratuitous ARP enabled, it looks a bit more stable, but I need to investigate in more detail.

I will give the new ones with ESP8285 a try. nice idea and thanks.
Joachim

Wifi Strength is -70 which is enough here. I am using S20 and S23 in the same location. I tend to agree with TD-er as it is not my first Sonoff basic that dies. They are pretty old, one of the first I bought couple of years ago. It also needed a couple of attempts to get the firmware on it, and I di...

I am using ESPEasy on numeric devices, but there is one Sonoff basic, pretty old hardware. I am using it with ESP_Easy_mega_20211105_normal_ESP8266_1M Nov 5 2021. Now the problem is, that this devices is not reachable from time to time. When I switch differnet Tabs, it can happen it is not reachable...

Whats blocking me? Basically I am just too lazy. But actually its something I will do, things are so much easier then...:-) no change of firmware needed: Solution: on led_on do if %systime% > 05:00:00 timerset,1,600 else timerset,1,180 endif if %systime% > 22:00:00 timerset,1,180 endif

Yes works, but I have 2 if's means its first loop will be overwritten by the second if-else

Hi i am using ESPEeasy now since a while but I am unsure how to seolve this: espeasy build is old: 147. I want to set a timer value shorter during 22h and 6h in the morning. (Bathlight) As far as I know variables like let,1,10 does not work in this old build. how can i solve this? on led_on do timer...

Hello, I m using Wiegand RFID for my garage door since a couple of years now.They are based on ESP01 ad Wiegand ports are GPIO2 Green and GPIO0 for White. This works perfectly. Now I am about to transfer this to a node MCU, as I also want to use more GPIOs for Door opening, LCD and current measureme...

Oh thanks a lot, so it basically means my swap of flash worked just fine....and I can change a couple more of my ESP01...
I was just wondering, because other units do not show this every minute..

BTW I love the small ESP01, although I have three of them in the garage now for different task.

Hi , I have changed the flash memory of an ESP01 from 1M to a 4MB Flash and put "ESP_Easy_mega_20210114_normal_ESP8266_4M1M_VCC.bin" on it. Now the ESP runs so far but it has the following messages in the log: WD : Uptime 0 ConnectFailures 0 FreeMem 26752 WiFiStatus 3 ESPeasy internal wifi...

Thanks for your help. Sendtohttp works fine, but it did not on the first run, but has nothing to do with this rule. The problem seemed to be the following: I used the RFID Wiegand input for quite a while with a very old build. (R147) It never worked good, and the ESP01 did not work after a few days....

Hi folks, I want to control my garage doors with 2 ESP01 and an RFID with another ESP01. The setup basically works but not reliably, esp. the triggering of the event. So there is an ESP01 which collects the RFID TAG information from the terminal. => works perfectly Based on the RFID Tag number it se...

Thanks a Lot, i will give it a try. So I used ESP_Easy_mega_20200703_normal_WROOM02_2M256 to flash the ESP01, which works quite well. It now says OTA yes, and it works... However I do not know the differences to the normal one (w/Vcc). The time server ntp does not work here. So the time always stays...

I have ugraded ESP01 to 2M Flash. (they where sent wrongly to my, but I still gave it a try) However, it also says I am not able to make a OTA upgrade. Why? There must be enough room. The flash size is correctly recognized.
Any Idea? However, it works with the 1M workaround.

Sending SMS from EASY ESP to a mobile Phone would be a nice feature, not what I want but i could use it...I need to check that. ( I could then send a sms to may camper which replies with all relevant data incl temp, Gaslevel (for the heater etc)) I wanted to modify the smoke sensor in my garage with...

I want to send a Text Message at System#Boot to my domoticz with SendtoHttp. Is this possible or not supported yet.
What i probably can do is to let the virtual Sensor switch from 0 to 1 and let Domoticz Create a message (Warning) I guess thats easier..

The Wiegand protocoll only works for RFID to my knowledge, not for fingerprint and not for the PIN you are able to enter.
Ever tried a RFID card and check the output?

driving the relay directly might be difficult for the ESP, as they draw too much current for the ESP.
Either use a transistor (easy) or optocoupler (also easy)

Finally works. I had ti uninstall several lib updates...

Hi all, i have connected three gpios to three MosFet controlling the RGB lines of a RGB LED. with PWM setting I can control all colors quite nicely. However, I do not fully understand how to connect the whole system to native domoticz now, using the RGB device which can be selected. Has someone done...

If I am going to compile ESPeasy I get the following failer which stopps compiling:

exit status 1
'IRrecv' does not name a type
How can I change this?

Many thanks
for your help.

Arduino 1.8.5
ESPeasy version: V2.0 dev12