Will have the timer set a variable,
Thanks for the info.
Regards Dave
Search found 25 matches
- 23 Apr 2019, 19:25
- Forum: ESP Easy: Software
- Topic: Why does this rule stop working ?
- Replies: 2
- Views: 4240
- 11 Apr 2019, 19:23
- Forum: ESP Easy: Software
- Topic: Why does this rule stop working ?
- Replies: 2
- Views: 4240
Why does this rule stop working ?
Hi Chaps, I am using version mega-20190305 This is a home brew beer fermentation chamber controller. I need a 15 minute timeout after the fridge compressor turns off before it gets turned on again. The rules below work once after boot when the temp rises above 18 degrees but once the temperature dro...
- 02 Apr 2019, 19:49
- Forum: ESP Easy: Hardware
- Topic: Support for PZEM 004T Energy monitor
- Replies: 309
- Views: 9132786
Re: Support for PZEM 004T Energy monitor
Cheers mate.
Very nice work !
Very nice work !
- 01 Apr 2019, 18:29
- Forum: ESP Easy: Hardware
- Topic: Support for PZEM 004T Energy monitor
- Replies: 309
- Views: 9132786
Re: Support for PZEM 004T Energy monitor
@serjkru. Please could you post the wiring schematic for the PZEM-004 modules to the ESP-8266 module,I do not see the pdf file. Looking at the wiring picture posted earlier, you are sequentially supplying power to the PZEM modules and taking readings to send to openhab. Good idea to save IO pins ! T...
- 26 Feb 2019, 19:03
- Forum: ESP Easy: Software
- Topic: How to read an IO pin state in rules ?
- Replies: 4
- Views: 6204
Re: How to read an IO pin state in rules ?
This now working well.grovkillen wrote: ↑25 Feb 2019, 19:24 If you use custom events you can use those to do more advanced rules.
Thank you for the tip
- 25 Feb 2019, 17:07
- Forum: ESP Easy: Software
- Topic: How to read an IO pin state in rules ?
- Replies: 4
- Views: 6204
How to read an IO pin state in rules ?
Hi All, I have the rule below working fine,however I want to be able to disable both rules when needed by setting an IO pin high from openhab. I can successfully toggle IO12 from openhab,I can see this in tools > pin state buffer,how do I read this pin state in rules to disable them when IO12 is hig...
- 28 Jan 2019, 19:04
- Forum: ESP Easy: Projects / Applications
- Topic: MQTT control IRsend plugin ?
- Replies: 2
- Views: 5256
Re: MQTT control IRsend plugin ?
Hi Iron, It works perfectly. Thanks for your help ! FYI - I had to use ESPeasy _V147_RC8 to get the amp to respond to IR commands. The later version of ESPeasy I tried first,flashed the red LED I fitted across the IR LED (so I can see if anything is going on) but amp did not respond. Looks like a va...
- 25 Jan 2019, 19:02
- Forum: ESP Easy: Projects / Applications
- Topic: MQTT control IRsend plugin ?
- Replies: 2
- Views: 5256
MQTT control IRsend plugin ?
I am running espeasy mega-20180822 and have it controlling my home theatre amp using HTTP but would like to use MQTT to send IR signals. http://192.168.100.1/control?cmd=IRSEND,NEC,3CC302FD,32 turns my amp on or off. What should the MQTT command look like if the unit name is BarIR and the device nam...
- 17 Jan 2019, 16:40
- Forum: ESP Easy: General Discussion
- Topic: endif vs endon
- Replies: 2
- Views: 4360
Re: endif vs endon
Thanks,
Are looking at the linked age now,
Cheers
Are looking at the linked age now,
Cheers
- 17 Jan 2019, 16:15
- Forum: ESP Easy: General Discussion
- Topic: endif vs endon
- Replies: 2
- Views: 4360
endif vs endon
Hi Chaps,
Could someone explain the difference between endif and endon used in espeasy rules and when each one should be used ?
I have looked at the wiki and it seems endif is needed when if / else statements are used,would like some further explanation.
cheers
Could someone explain the difference between endif and endon used in espeasy rules and when each one should be used ?
I have looked at the wiki and it seems endif is needed when if / else statements are used,would like some further explanation.
cheers
- 11 Jan 2019, 19:59
- Forum: ESP Easy: Software
- Topic: Possible to use previoustate in rules ?
- Replies: 4
- Views: 6126
Re: Possible to use previoustate in rules ?
Thanks iron for the idea,rule below working perfectly, I was thinking of setting up a dummy item but this is a simpler method .. On WaterLevel#Litres>220 do if [TankSolenoid#State]=0 gpio,13,1 gpio,14,0 Pulse,4,1,500 endon On WaterLevel#Litres<220 do if [MuniSolenoid#State]=0 gpio,14,1 gpio,13,0 Pul...
- 10 Jan 2019, 19:26
- Forum: ESP Easy: Software
- Topic: Possible to use previoustate in rules ?
- Replies: 4
- Views: 6126
Re: Possible to use previoustate in rules ?
Hi,
Thanks for the reply,however I am trying to configure the rules so they trigger once only when the waterlevel#litres>10 and again when waterlevel#litres<10 condition is met,not pulse the solenoid control IO's over and over.
Thanks for the reply,however I am trying to configure the rules so they trigger once only when the waterlevel#litres>10 and again when waterlevel#litres<10 condition is met,not pulse the solenoid control IO's over and over.
- 10 Jan 2019, 17:48
- Forum: ESP Easy: Software
- Topic: Possible to use previoustate in rules ?
- Replies: 4
- Views: 6126
Possible to use previoustate in rules ?
Hi Chaps, ESPeasy is monitoring my rain water tanks and controlling 2 latching solenoid valves - one on tank supply to house and another on the council water feed. I use the rules below but the solenoids are pulsed every few seconds even if their state does not need to change. On WaterLevel#Litres>1...
- 01 Oct 2018, 17:45
- Forum: ESP Easy: Software
- Topic: How to disable rule at a specific time ?
- Replies: 28
- Views: 39654
Re: How to disable rule at a specific time ?
Good idea,will set it up like that.
Thank you
Thank you
- 28 Sep 2018, 20:08
- Forum: ESP Easy: Software
- Topic: How to disable rule at a specific time ?
- Replies: 28
- Views: 39654
Re: How to disable rule at a specific time ?
on Pir_Sensor#Pir=1 do if [LDR#Analog]>1000 AND [Saturday#Inhibit]=0 Publish RGB/0017F169/color/set,200,200,200 Publish RGB/0017F169/brightness/set,200 endif endon on Pir_Sensor#Pir=0 do if [LDR#Analog]>1000 AND [Saturday#Inhibit]=0 Publish RGB/0017F169/state/set,OFF endif endon These rules are wor...
- 28 Aug 2018, 17:50
- Forum: ESP Easy: Software
- Topic: How to disable rule at a specific time ?
- Replies: 28
- Views: 39654
Re: How to disable rule at a specific time ?
The PIR delay is set to 1 as I wanted a quick response once motion is detected.
Will this constant publishing slow broker response down at all ?
Openhab and mosquitto broker is running on a Pi 2.
Thanks again for the help chaps !
Will this constant publishing slow broker response down at all ?
Openhab and mosquitto broker is running on a Pi 2.
Thanks again for the help chaps !
- 27 Aug 2018, 17:56
- Forum: ESP Easy: Software
- Topic: How to disable rule at a specific time ?
- Replies: 28
- Views: 39654
Re: How to disable rule at a specific time ?
On Clock#Time=Sat,16:00 do TaskValueSet 3, 1, 1 endon On Clock#Time=Sat,22:00 do TaskValueSet 3, 1, 0 endon on Pir_Sensor#Pir=1 do if [LDR#Analog]>1000 AND [Saturday#Inhibit]=0 Publish RGB/0017F169/color/set,200,200,200 Publish RGB/0017F169/brightness/set,200 endif endon on Pir_Sensor#Pir=0 do if [...
- 24 Aug 2018, 17:35
- Forum: ESP Easy: Software
- Topic: How to disable rule at a specific time ?
- Replies: 28
- Views: 39654
Re: How to disable rule at a specific time ?
Thank you Toffel969,
That is exactly what I want to achieve.
Will try it.
Regards
Dave
That is exactly what I want to achieve.
Will try it.
Regards
Dave
- 23 Aug 2018, 17:59
- Forum: ESP Easy: Software
- Topic: How to disable rule at a specific time ?
- Replies: 28
- Views: 39654
Re: How to disable rule at a specific time ?
I saw that but it details how to enable a rule or some operation,not disabling a rule.
I understand the day and time configuration but do not know how to implement the disabling of the rule between the 2 times
I will search further then.
I understand the day and time configuration but do not know how to implement the disabling of the rule between the 2 times
I will search further then.
- 22 Aug 2018, 19:02
- Forum: ESP Easy: Software
- Topic: How to disable rule at a specific time ?
- Replies: 28
- Views: 39654
How to disable rule at a specific time ?
Hi All, How can I disable the rule below every saturday from 16:00 till 23:00 only,every other day rule must be active. on Pir_Sensor#Pir=1 do if [LDR#Analog]<500 Publish RGB/0017F169/color/set,200,200,200 Publish RGB/0017F169/brightness/set,200 else Publish RGB/0017F169/brightness/set,0 endif endon...
- 23 Jul 2018, 19:24
- Forum: ESP Easy: Software
- Topic: Filter Rule For Ultrasonic Distance Sensor
- Replies: 0
- Views: 3134
Filter Rule For Ultrasonic Distance Sensor
Hi All, Please help a noob with espeasy rules ... I have a JSN-SR04T waterproof ultrasonic sensor I intend to measure water level in a rain water harvesting tank. These sensors also work with the newping libary. When testing the sensor,every so often a zero value is returned otherwise readings are q...
- 04 May 2018, 17:46
- Forum: ESP Easy: Hardware
- Topic: Support for PZEM 004T Energy monitor
- Replies: 309
- Views: 9132786
Re: Support for PZEM 004T Energy monitor
Thank you maluko.
Will compile this and test it.
Only need MQTT functionality !
Will compile this and test it.
Only need MQTT functionality !
- 03 May 2018, 19:24
- Forum: ESP Easy: Hardware
- Topic: Support for PZEM 004T Energy monitor
- Replies: 309
- Views: 9132786
Re: Support for PZEM 004T Energy monitor
Hi All, Have flashed a wemos D1 mini and a nodemcu module with the firmware build posted on this thread (ESPEasy-2.0.0-dev12_test_4096.bin.zip) with the same results. All options can be configured with no issues until selecting the PZEM004 as a device and configuring GPIO's and pressing submit radio...
- 12 Feb 2018, 18:21
- Forum: ESP Easy: Software
- Topic: ESP Rules
- Replies: 3
- Views: 5277
Re: ESP Rules
Those rules perfectly,thanks
Do ESPeasy rules support =< and => or only <,> and =
Do ESPeasy rules support =< and => or only <,> and =
- 12 Feb 2018, 17:46
- Forum: ESP Easy: Software
- Topic: ESP Rules
- Replies: 3
- Views: 5277
ESP Rules
Good Day All, Thanks to everyone involved in the development of this brilliant firmware for the ESP8266, I have found it most useful and stable. I am building a peltier temperature controller for home brewing fermentation, IO 12 to cool and IO 14 to heat,the rules below are working well,but I need b...