Hi.
Nowhere can I find information whether sonoff T2 is hardware compatible with sonoff t1.
Can espeasy be flashed on sonoff t2? Or any other like as Tasmota, Espurna etc?
No info, no images, no pinouts about Sonoff T2? Strange.
Search found 44 matches
- 08 Sep 2019, 21:42
- Forum: ESP Easy: Hardware
- Topic: Sonoff T2 I need some info.
- Replies: 1
- Views: 9017
- 31 Jul 2019, 00:48
- Forum: ESP Easy: Hardware
- Topic: Support for PZEM 004T Energy monitor
- Replies: 309
- Views: 9289082
Re: Support for PZEM 004T Energy monitor
gumilev If you need only one device you can use Tasmota software.
PZEM004T v3 uses same protocol as PZEM-016 So you need set proper rx and tx gpio's in config.
PZEM004T v3 uses same protocol as PZEM-016 So you need set proper rx and tx gpio's in config.
- 18 Jul 2019, 14:45
- Forum: ESP Easy: General Discussion
- Topic: Power Outage detector
- Replies: 2
- Views: 8574
Re: Power Outage detector
You can use a optocupler connected to gpio.
- 15 Jul 2019, 10:38
- Forum: ESP Easy: Hardware
- Topic: Support for PZEM 004T Energy monitor
- Replies: 309
- Views: 9289082
Re: Support for PZEM 004T Energy monitor
Hi I ordered PZEM-004 and got V3.0 version.
This version have new mdbus MTU protocol.
Someone tried develop a plugin?
This version have new mdbus MTU protocol.
Someone tried develop a plugin?
- 04 Jul 2019, 14:08
- Forum: ESP Easy: Software
- Topic: Not configured in Station Mode!
- Replies: 8
- Views: 7201
Re: Not configured in Station Mode!
Let's try flash whole area with blank.bin and after upload ESPEasy again. I had same issue on few boards.
If you have 1mb use 1 mb blank or 4 mb for 4mb IC's
If you have 1mb use 1 mb blank or 4 mb for 4mb IC's
- 03 Jun 2019, 13:29
- Forum: ESP Easy: Hardware
- Topic: Support for PZEM 004T Energy monitor
- Replies: 309
- Views: 9289082
Re: Support for PZEM 004T Energy monitor
serjkru Why did you removed R15?
And why you swap R17 to 120 Ohm except 510 Ohm?
It would not be enough to solder 1k resistor as in the picture?
And why you swap R17 to 120 Ohm except 510 Ohm?
It would not be enough to solder 1k resistor as in the picture?
- 05 Apr 2019, 23:07
- Forum: ESP Easy: General Discussion
- Topic: what is best android push notification app for espeasy?
- Replies: 2
- Views: 5360
Re: what is best android push notification app for espeasy?
I think much easy will be using telegram as same way as old domoticz solution using http request.
- 03 Apr 2019, 14:43
- Forum: ESP Easy: Hardware
- Topic: Support for PZEM 004T Energy monitor
- Replies: 309
- Views: 9289082
Re: Support for PZEM 004T Energy monitor
Very good idea.
What is the reading time of all sensors?
How often can you read?
What is the reading time of all sensors?
How often can you read?
- 16 Feb 2019, 02:42
- Forum: ESP Easy: Software
- Topic: longpress action without first have the shortpress action
- Replies: 10
- Views: 8176
Re: longpress action without first have the shortpress action
You not using a timer to determine when is a short press and when is a long.
See at rules tutorial info:
See at rules tutorial info:
Code: Select all
on Button#State=1 do
timerSet,1,1
endon
on rules#timer=1 do
if [Button#State]=0
//Action if button is short pressed
else
//Action if button is still pressed
endif
endon
- 09 Feb 2019, 00:03
- Forum: ESP Easy: General Discussion
- Topic: Can't compile with a new plugin (PZEM004T)
- Replies: 22
- Views: 35515
Re: Can't compile with a new plugin (PZEM004T)
For me it does not work too. But i get connected another uart converter to tx from pzem module and it send data, but showing only zero values on devices page. Below is a scrren from hercules due sending data from pzem module. I tried changing pins, enabling input, comile with different cores etc. an...
- 11 Dec 2018, 21:33
- Forum: ESP Easy: Projects / Applications
- Topic: Calculating kWh from Amps+Volts
- Replies: 10
- Views: 11501
Re: Calculating kWh from Amps+Volts
So you have to feature request Nettemp developers for derive and difference functions over time. Tu calculate kWh need stored all momentary values over the time. Espeasy doses not have a storing database, so calculate derivative is not possible without stored data. Data store is not possible without...
- 11 Dec 2018, 15:50
- Forum: ESP Easy: Projects / Applications
- Topic: Calculating kWh from Amps+Volts
- Replies: 10
- Views: 11501
Re: Calculating kWh from Amps+Volts
I don't think so.
To compute kWh from recent instantaneous power you have to calculate derivative.
What a database you use?
I had influxdb with grafana and is possible with it. But you have to set a server machine.
To compute kWh from recent instantaneous power you have to calculate derivative.
What a database you use?
I had influxdb with grafana and is possible with it. But you have to set a server machine.
- 03 Dec 2018, 15:26
- Forum: ESP Easy: General Discussion
- Topic: Reading data from Domoticz to nodeMCU
- Replies: 3
- Views: 4369
Re: Reading data from Domoticz to nodeMCU
Reading data from dummy sensor in domoticz is not so easy. You have to create your own lua/dzEvents script and trigger it.
Even domoticz remote server can't pass dummy data.
Even domoticz remote server can't pass dummy data.
- 26 Sep 2018, 22:36
- Forum: ESP Easy: Software
- Topic: Software problem with BME280 (today RC)
- Replies: 4
- Views: 4297
Re: Software problem with BME280 (today RC)
I just checked and for me BME280 works well on this release (24.09). All values on 76 address displayed.
- 24 Sep 2018, 21:56
- Forum: ESP Easy: General Discussion
- Topic: Push button state without toggle
- Replies: 7
- Views: 5622
Re: Push button state without toggle
Did you marked internal pull-up?
And set to "Push button active low"
And set to "Push button active low"
- 23 Sep 2018, 10:16
- Forum: ESP Easy: General Discussion
- Topic: How to switch two Oled task on the same display?
- Replies: 3
- Views: 4281
Re: How to switch two Oled task on the same display?
I added my first issue for this ability.
I don't know how to label "Feature request"
https://github.com/letscontrolit/ESPEasy/issues/1783
I don't know how to label "Feature request"
https://github.com/letscontrolit/ESPEasy/issues/1783
- 22 Sep 2018, 01:25
- Forum: ESP Easy: General Discussion
- Topic: How to switch two Oled task on the same display?
- Replies: 3
- Views: 4281
How to switch two Oled task on the same display?
Hello. Is it possible to switch tasks in any way? I have one OLED connected to Wemos D1 mini. I have two tasks for the OLED display. The first task uses the normal mode and the second task uses a framed mode Of course, I do not want them to work at the same time. I would like to be able to switch th...
- 06 Sep 2018, 22:43
- Forum: ESP Easy: Software
- Topic: Cant connect after update mega-20180822
- Replies: 7
- Views: 6663
Re: Cant connect after update mega-20180822
I had the same issue two months ago with the exactly same hardware. I don't remember what exactly was a espeasy version. After i tried reflash with another versions and still did not connected. Finally I flash whole flash area with blank 4mb file and next with firmware what previously was not connec...
- 04 Jul 2018, 22:17
- Forum: ESP Easy: Software
- Topic: sunrise/sunset to be used in rule
- Replies: 45
- Views: 27011
Re: sunrise/sunset to be used in rule
Perhaps that way:
Code: Select all
on Clock#Time=All,%sunrise% do
if <test>
<action>
<action>
endif
endon
- 04 Jul 2018, 00:07
- Forum: ESP Easy: Software
- Topic: time zone and offset
- Replies: 2
- Views: 4168
Re: time zone and offset
What exactly build you use?
Timezone offset is nearly above location settings.
Timezone offset is nearly above location settings.
- 26 Jun 2018, 23:42
- Forum: ESP Easy: General Discussion
- Topic: Why some kind of events does not show on OLED SSD1306?
- Replies: 1
- Views: 2758
Why some kind of events does not show on OLED SSD1306?
Hi I wanted to send some of data using SendTo And its works because I see it in logs on another device with values but I can't display the value on OLED. Same as I tried to display [Clock#Time] its also not show. I know %systime% is displayed well, but why some values is possible to display and some...
- 26 Jun 2018, 23:21
- Forum: ESP Easy: Projects / Applications
- Topic: ESP EASY sending data
- Replies: 3
- Views: 4820
Re: ESP EASY sending data
I think is could be a bug in ser2net plugin because !Serial# does not have a value name so %eventvalue% does not work.
- 26 Jun 2018, 23:15
- Forum: ESP Easy: Software
- Topic: Serial input to MQTT
- Replies: 2
- Views: 4478
Re: Serial input to MQTT
Hi I just read about your problem and I have an idea. On !Serial# do publish home/ESP07/Alarm,%eventvalue% Endon Because !Serial# does not have a value name. You can try use a prefix on sending data as: myname= and after send your data Obviously if you have an impact on the format of the data being ...
- 02 Jun 2018, 01:29
- Forum: ESP Easy: General Discussion
- Topic: Soap control messages from ESP Easy?
- Replies: 0
- Views: 2671
Soap control messages from ESP Easy?
Hi I am curious if it is possible to send soap messages from espeasy to Panasonic Viera TV to control it as in Domoticz. But directly from esp device. Has anyone tried or opened feature request? Ok I did some research and now be able to send command from Hercules using captured frame: POST /nrc/cont...
- 11 May 2018, 19:31
- Forum: ESP Easy: Software
- Topic: The rule how to do it
- Replies: 3
- Views: 3849
Re: The rule how to do it
Try something like that. Im not tested it. on Przycisk#Switch do if [Relay#Switch]=1 timerSet,1,0 /disable timer just in case gpio,12,0 // first relay on gpio,13,0 //second relay on else timerSet,1,600 //set timer1 to count 10 minutes gpio,12,1 //first relay off endif endon On Rules#Timer=1 do gpio,...
- 11 May 2018, 14:20
- Forum: ESP Easy: Software
- Topic: Serial MCU controlled relay/switch
- Replies: 459
- Views: 1120639
Re: Serial MCU controlled relay/switch
Yes you have right. Domoticz does not care about switch reply.
So simply OK will be good.
So simply OK will be good.
- 09 May 2018, 12:14
- Forum: ESP Easy: Software
- Topic: Serial MCU controlled relay/switch
- Replies: 459
- Views: 1120639
Re: Serial MCU controlled relay/switch
I can modify the code the output some meaningless text, such as "command completed", if anybody need it. if it was not a problem, I would ask for such function because Domoticz need any response otherwise shows error. It would be nice if the response would be in JSON format. Üdvözlet Leng...
- 09 May 2018, 00:38
- Forum: ESP Easy: General Discussion
- Topic: About the PUYA version
- Replies: 10
- Views: 12550
Re: About the PUYA version
Spiffs size is depending how much plugins you have. I compiled with normal and added only serial mcu controlled relay. I set 128k spiffs.
- 02 May 2018, 11:42
- Forum: ESP Easy: Software
- Topic: Adding a new device type
- Replies: 5
- Views: 6800
Re: Adding a new device type
Look at how other plugins are written.
In my opinion, you should connect the Uart-RS485 converter between inverter and the UART of esp8266 board.
Then after conversion, you can parse data like ser2net.
In my opinion, you should connect the Uart-RS485 converter between inverter and the UART of esp8266 board.
Then after conversion, you can parse data like ser2net.
- 01 May 2018, 10:43
- Forum: ESP Easy: General Discussion
- Topic: Wemos D1 mini pro. Not enough space using OTA?
- Replies: 8
- Views: 8756
Re: Wemos D1 mini pro. Not enough space using OTA?
Okay. Now everything is clear. Thanks.
- 01 May 2018, 10:41
- Forum: ESP Easy: Software
- Topic: Serial MCU controlled relay/switch
- Replies: 459
- Views: 1120639
Re: Serial MCU controlled relay/switch
Yes, I used sources from yesterday and patched Esp.cpp and obviously your nice plugin. Working well witch domoticz ESP-01s and LC TECH single relay. Added a button and some rules to get full feedback about relay state. on sonoff#Relay0 do Publish domoticz/in,{"idx":92,"nvalue":[s...
- 01 May 2018, 00:04
- Forum: ESP Easy: General Discussion
- Topic: About the PUYA version
- Replies: 10
- Views: 12550
Re: About the PUYA version
Please overwrite your Esp.cpp using following file. And after you can compile binaries for PUYA flash IC. This file should be in your core path as: /home/yourname/.arduino15/packages/esp8266/hardware/esp8266/2.4.1/cores (if you use Arduino) The archive contains two files: patched and original. So yo...
- 30 Apr 2018, 23:51
- Forum: ESP Easy: Software
- Topic: Serial MCU controlled relay/switch
- Replies: 459
- Views: 1120639
Re: Serial MCU controlled relay/switch
If someone would like test it. Compiled using recent sources (core 2.4.1)
I compiled it with PUYA patched Esp.cpp
It should by work with differ than PUYA flash IC too.
To fit in 1MB II got rid of some plugins that I think it can not be used with serial controlled boards.
I compiled it with PUYA patched Esp.cpp
It should by work with differ than PUYA flash IC too.
To fit in 1MB II got rid of some plugins that I think it can not be used with serial controlled boards.
- 30 Apr 2018, 23:25
- Forum: ESP Easy: General Discussion
- Topic: Wemos D1 mini pro. Not enough space using OTA?
- Replies: 8
- Views: 8756
Re: Wemos D1 mini pro. Not enough space using OTA?
I selected from tools/boards "Wemos D1 mini pro" It has only to choose 15MB SPIFFS. I thought that having 15MB spiffs would not be problems with OTA Formatting after flashing takes a lot of time. So I think that SPIFFS is proper created. Perhaps mega sources still does not support size mor...
- 30 Apr 2018, 18:58
- Forum: ESP Easy: General Discussion
- Topic: Wemos D1 mini pro. Not enough space using OTA?
- Replies: 8
- Views: 8756
Re: Wemos D1 mini pro. Not enough space using OTA?
Previous version is 15MB I want to upgrade new 15MB on an old 15MB. Compiled on Arduino using "Wemos D1 mini pro" from menu. Latest sources and core 2.4.1 Build 20102 - Mega (ESP82xx Core 2_4_1, NONOS SDK 2.2.1(cfd48f3)) GIT version xuryV0.1 Plugins 47 [Normal] Build time Apr 30 2018 18:28...
- 30 Apr 2018, 18:38
- Forum: ESP Easy: General Discussion
- Topic: Wemos D1 mini pro. Not enough space using OTA?
- Replies: 8
- Views: 8756
Wemos D1 mini pro. Not enough space using OTA?
I have done compiled and flashed Wemos D1 mini pro with 15MB SPIFFS.
Sketch size is about 634kB.
Now I had update using OTA and I have not enough space. Why?
Were the bin file is loaded using OTA ? To RAM? Or SPIFFS is too large?
Sorry for the basic questions but I'm rookie lamer.
Sketch size is about 634kB.
Now I had update using OTA and I have not enough space. Why?
Were the bin file is loaded using OTA ? To RAM? Or SPIFFS is too large?
Sorry for the basic questions but I'm rookie lamer.
- 25 Apr 2018, 18:41
- Forum: ESP Easy: Software
- Topic: Serial MCU controlled relay/switch
- Replies: 459
- Views: 1120639
Re: Serial MCU controlled relay/switch
If you want use another plugins not included in bin files shared at first post you have to compile using Arduino or Platformio. About problems with new releases you mast observe serial output during connection and read logs data. P.S I have request to enesbcs. If is possible to fix a plugin? On rece...
- 25 Apr 2018, 00:36
- Forum: ESP Easy: Hardware
- Topic: Support for "Sonoff Pow" (from ITead) with Power Consumption Measurement via HLW8012 (HLW 8012) IC?
- Replies: 146
- Views: 243956
Re: Support for "Sonoff Pow" (from ITead) with Power Consumption Measurement via HLW8012 (HLW 8012) IC?
Thank You TD-er. I think at least I understood the define system. Only one question: I would like not touch too much in main files as I far away from code developing. So I read some info And prepare Custom.h file. So can I put my custom definitions on custom.h ? For eq #undef PLUGIN_BUILD_NORMAL #de...
- 24 Apr 2018, 21:40
- Forum: ESP Easy: Hardware
- Topic: Support for "Sonoff Pow" (from ITead) with Power Consumption Measurement via HLW8012 (HLW 8012) IC?
- Replies: 146
- Views: 243956
Re: Support for "Sonoff Pow" (from ITead) with Power Consumption Measurement via HLW8012 (HLW 8012) IC?
Please help me.
How to set PLUGIN_SET_SONOFF_POW to compile in Arduino?
How to set PLUGIN_SET_SONOFF_POW to compile in Arduino?
- 22 Apr 2018, 17:23
- Forum: ESP Easy: General Discussion
- Topic: About the PUYA version
- Replies: 10
- Views: 12550
Re: About the PUYA version
I spent lot of time trying compile for PUYA using platformIO with no success. So I swap to Arduino on Debian, and now is much better. I have patched esp.ccp with proper patch. When I'll come back home I can attach a patch or esp.ccp file for 2.4.1 core I use it witch ESP-01s and everything sims work...
- 16 Apr 2018, 01:09
- Forum: ESP Easy: Software
- Topic: Serial MCU controlled relay/switch
- Replies: 459
- Views: 1120639
Re: Serial MCU controlled relay/switch
Ok. I finally managed to compile with what I need.
It was a problem with PUYA chip.
After patching Esp.cpp it works well.
It was a problem with PUYA chip.
After patching Esp.cpp it works well.
- 04 Apr 2018, 18:29
- Forum: ESP Easy: Software
- Topic: Serial MCU controlled relay/switch
- Replies: 459
- Views: 1120639
Re: Serial MCU controlled relay/switch
As your suggestion I managed to compile on 2.3.0 core. Plugin sims work OK but when I try add new device I have error in red frame: I guess is a filesystem error. Maybe not enough flash? Or is wrong organization, because I had another version of firmware before. I'll tray to disable some unneeded pl...
- 04 Apr 2018, 12:02
- Forum: ESP Easy: Software
- Topic: Serial MCU controlled relay/switch
- Replies: 459
- Views: 1120639
Re: Serial MCU controlled relay/switch
Thank You enesbcs I will try to compile with your sugestions this evening when I come back home. I need it for lc tech relay so I hope should be good with buffer size 32. I have one more request. Would you like give me a link for a core 2.4.0 source because as I said im totally beginner. A don't kno...
- 03 Apr 2018, 19:37
- Forum: ESP Easy: Software
- Topic: Serial MCU controlled relay/switch
- Replies: 459
- Views: 1120639
Re: Serial MCU controlled relay/switch
Hello everybody. I'm newbie on this forum, and totally beginner with platformio. I'd like to ask tou how to compile this plugin on 2.3.0 core? I got error: :/ESPEasy-mega-20180402/src/_P165_SerSwitch.ino: In function 'boolean Plugin_165(byte, EventStruct*, String&)': L:/ESPEasy-mega-20180402/src...