Search found 13 matches

by NickOver
15 Apr 2018, 12:24
Forum: ESP Easy: General Discussion
Topic: How to read GPIO state?
Replies: 14
Views: 4554

Re: How to read GPIO state?

Ok, i check time between update and now esp need more than 7 minutes to update pin state. Can i speed up this?
EDIT
Now update from high to low lested something near minute. How it's work?
by NickOver
15 Apr 2018, 12:01
Forum: ESP Easy: General Discussion
Topic: How to read GPIO state?
Replies: 14
Views: 4554

Re: How to read GPIO state?

Yeah, i refresh /devices tab.
In log i have only info about network

EDIT
I got something. In log i got:
1504911 : SW : Switch state 1 Output value 1
And after set low state i got 0 but after a long time. Is ESP need minute or two to update GPIO state?
by NickOver
15 Apr 2018, 11:57
Forum: ESP Easy: General Discussion
Topic: How to read GPIO state?
Replies: 14
Views: 4554

Re: How to read GPIO state?

I don't understand why it doesn't work.
I set everything almost as you:
https://imgur.com/a/BUMm4
set high state on gpio2 and all time i get 0.
I try select all pins, but always i got 0.
by NickOver
14 Apr 2018, 17:49
Forum: ESP Easy: General Discussion
Topic: How to read GPIO state?
Replies: 14
Views: 4554

Re: How to read GPIO state?

I think only if i give to CH_PD high state gpio0 are determinate flashing mode.
Ok, i change to gipo2, but still without any results. Changing state doesn't give any result.

EDIT
It's strange but when i check 'Invereted output) in /devices value dont change.
by NickOver
14 Apr 2018, 17:28
Forum: ESP Easy: General Discussion
Topic: How to read GPIO state?
Replies: 14
Views: 4554

Re: How to read GPIO state?

I check 'Send To Controller' And set idx to 1, but still in /pinstates it show 0
by NickOver
14 Apr 2018, 17:14
Forum: ESP Easy: General Discussion
Topic: How to read GPIO state?
Replies: 14
Views: 4554

Re: How to read GPIO state?

My usage case is pretty simple. ESP are connected to device sending low or high state. I need read that state by http request (i know how ;)) but all time in /pinstates i got 0.
It's how i set :
https://imgur.com/a/wAa3k
by NickOver
14 Apr 2018, 12:24
Forum: ESP Easy: General Discussion
Topic: How to read GPIO state?
Replies: 14
Views: 4554

How to read GPIO state?

Hi!
I have second blocking problem.
I connect ESP-01 as following:
https://imgur.com/a/TxlXn

On raspberry i set GPIO2 as out with high state (i check it with multimeter).
I setup ESP as following:
https://imgur.com/a/n4XIC
But as value i have only 0.
What im doing wrong?
by NickOver
14 Apr 2018, 10:43
Forum: ESP Easy: General Discussion
Topic: Any WiFi after flash
Replies: 10
Views: 3070

Re: Any WiFi after flash

After debug via serial monitor it's look like it alive, and broadcast on 192.168.0.192. But it's strange why my ruter dont show it. Ok, thank you so much for help. You have big beer from me ;)
by NickOver
13 Apr 2018, 22:41
Forum: ESP Easy: General Discussion
Topic: Any WiFi after flash
Replies: 10
Views: 3070

Re: Any WiFi after flash

Ok, i upload binary: ESP_Easy_mega-20180413_dev_ESP8266PUYA_1024.bin Before that i clear memory. Now i got ESP_Easy_0, i log in, set network, set password, im redirect to "timer" page and after few seconds connection are broken i i got info about getting IP address. After few second networ...
by NickOver
13 Apr 2018, 21:14
Forum: ESP Easy: General Discussion
Topic: Any WiFi after flash
Replies: 10
Views: 3070

Re: Any WiFi after flash

I use ESP_Easy_mega-20180413_normal_ESP8266_1024.bin so i think it's correct. Yeah, have PUYA label. Now i loaded blank_1MB.bin (its bin with only 0) and ESP dont broadcast any network. Wi will see what been after load one mor time EasyESP binary. EDIT Ok, after load EasyESP i got network named 'ASP...
by NickOver
13 Apr 2018, 20:20
Forum: ESP Easy: General Discussion
Topic: Any WiFi after flash
Replies: 10
Views: 3070

Re: Any WiFi after flash

Ok, so how i can remove them?
by NickOver
13 Apr 2018, 20:13
Forum: ESP Easy: General Discussion
Topic: Any WiFi after flash
Replies: 10
Views: 3070

Re: Any WiFi after flash

If its true why FaryLink_1D796A network are shown?
by NickOver
13 Apr 2018, 19:29
Forum: ESP Easy: General Discussion
Topic: Any WiFi after flash
Replies: 10
Views: 3070

Any WiFi after flash

Hi After flash ESP01(1kb) any wifi named ESP_Easy_0 or ESP_0 isn't avalible. Flashing tool give me info is everything ok, so i remove converter and connect power ( VCC + CH_PD to VCC GND to GND ). I don't got these networks so i connect to converter ( TX - RX RX-TX VCC + CH_PD - VCC GND - GND ) to g...