Search found 106 matches

by Patou
16 Jun 2023, 22:25
Forum: ESP Easy: Software
Topic: Can I test if a timer is still running
Replies: 2
Views: 802

Re: Can I test if a timer is still running

Nice proposal and solving the request
Thanks
Patou
by Patou
16 Jun 2023, 19:19
Forum: ESP Easy: Software
Topic: Can I test if a timer is still running
Replies: 2
Views: 802

Can I test if a timer is still running

Hello, I have following case. If temp value is lower than setpoint activate a relay. Set min on time for the relay = 10 min (600sec). If temp value is higher than setpoint and the 10 min are not elapsed keep relay activated If temp value is higher than setpoint and the 10 min are elapsed : relay off...
by Patou
16 May 2023, 19:44
Forum: ESP Easy: Software
Topic: Esp 32 : P39 Max 31865 needs submit task after reboot
Replies: 1
Views: 784

Re: Esp 32 : P39 Max 31865 needs submit task after reboot

I found the problem the GPIO 19 witch is used as chip set was also defined as switch input in another task !!
Patou
by Patou
16 May 2023, 19:21
Forum: ESP Easy: Software
Topic: Esp 32 : P39 Max 31865 needs submit task after reboot
Replies: 1
Views: 784

Esp 32 : P39 Max 31865 needs submit task after reboot

Hello friends, Probably little bug in the software of P39 plugin. I use Max 31865 with RTD PT 100 2 wires on task 1. No other task or rules running at the moment. Binary Filename: ESP_Easy_mega_20230508_climate_ESP32_4M316k. It took quiet a time to have the correct temp reading. I had always a readi...
by Patou
05 Dec 2022, 22:21
Forum: ESP Easy: Software
Topic: Plug-in for MAX31865 RTD or MAX31856 Thermocouple IC?
Replies: 29
Views: 14251

Re: Plug-in for MAX31865 RTD or MAX31856 Thermocouple IC?

Hello
Thanks for your super fast reaction.
I will try this soon
Patrick
by Patou
05 Dec 2022, 21:10
Forum: ESP Easy: Software
Topic: Plug-in for MAX31865 RTD or MAX31856 Thermocouple IC?
Replies: 29
Views: 14251

Re: Plug-in for MAX31865 RTD or MAX31856 Thermocouple IC?

Hello friends,
Simple question :
Is this plugin supporting multiple Max 31865 board ?
If yes, how to address them ?
Thanks in advance
Patrick
by Patou
27 Oct 2022, 13:17
Forum: ESP Easy: Software
Topic: Boot difficulties with mega 20220809 ESP8266 normal 4M1M
Replies: 4
Views: 2140

Re: Boot difficulties with mega 20220809 ESP8266 normal 4M1M

Hello,
Good news, this build solve the problem. I tried 20 reboots and all where successfull.
Thanks for the quick reaction
Patou
by Patou
26 Oct 2022, 13:54
Forum: ESP Easy: Software
Topic: Boot difficulties with mega 20220809 ESP8266 normal 4M1M
Replies: 4
Views: 2140

Boot difficulties with mega 20220809 ESP8266 normal 4M1M

Hello, I am using Wemos mini pro but same problem with Wemos D1 mini. New pcb or pcb with first a blank flash or upgrade over ota : same problem. Once every 5 ... 6 boots the boot hangs with the IP adresse definition. See bellow log from normal boot : INIT : Booting version: mega-20220809_57b0c0c (E...
by Patou
22 Mar 2022, 22:45
Forum: ESP Easy: Software
Topic: maybe easier to use Dashboard replacement
Replies: 188
Views: 228070

Re: maybe easier to use Dashboard replacement

Good guide ... easy to follow
Thanks
Patou
by Patou
16 Feb 2022, 19:25
Forum: ESP Easy: Software
Topic: maybe easier to use Dashboard replacement
Replies: 188
Views: 228070

Re: maybe easier to use Dashboard replacement

Hello, I did not find enough explanation in your post about date time day month and year so please adapt the text when you have more time I added the last iframe at the end of the document. Nice work ( I can only write manuals ! not able to do your job but I appreciate to use it) https://docs.google...
by Patou
11 Feb 2022, 15:33
Forum: ESP Easy: Software
Topic: maybe easier to use Dashboard replacement
Replies: 188
Views: 228070

Re: maybe easier to use Dashboard replacement

Hello friends, Thanks for the Dashboard, I took some time to read and understand all the evolution of the included features. This is work in progress. As the progress is already quiet far, I took the time to make some kind of tutorial for other interested people. Chromo23 : please read it carefully ...
by Patou
18 Dec 2021, 02:01
Forum: ESP Easy: General Discussion
Topic: Best prototype pcb design service
Replies: 2
Views: 4666

Re: Best prototype pcb design service

Hello,
Indeed I saw now that on the final order page the duties and taxes are indicated
Patou
Image
by Patou
17 Dec 2021, 17:59
Forum: ESP Easy: General Discussion
Topic: Best prototype pcb design service
Replies: 2
Views: 4666

Best prototype pcb design service

Hello, Up to some months ago I was using Easy EDA services. Good design software, interesting prices and good service. Actually with the new import duty and VAT also for small package the price of the import duty and fee for duty declaration in Belgium make the price triple. Does someone knows an al...
by Patou
05 Nov 2021, 17:16
Forum: ESP Easy: General Discussion
Topic: Notepad++ Rules syntax highlight
Replies: 23
Views: 12559

Re: Notepad++ Rules syntax highlight

Perfect ...
I shall test in the coming days
Have a nice wk
Patou
by Patou
04 Nov 2021, 21:24
Forum: ESP Easy: General Discussion
Topic: Notepad++ Rules syntax highlight
Replies: 23
Views: 12559

Re: Notepad++ Rules syntax highlight

Done hope is now available
by Patou
04 Nov 2021, 20:03
Forum: ESP Easy: General Discussion
Topic: Notepad++ Rules syntax highlight
Replies: 23
Views: 12559

Re: Notepad++ Rules syntax highlight

Hello I have extended the work of Grokvillen with all the commands present actually in the doc. General commands and plugin specific commands have different colors. I am not familiar with the Github update of files. So please find in attachment the new .xml file. Please double check and publish it t...
by Patou
04 Nov 2021, 11:53
Forum: ESP Easy: General Discussion
Topic: Notepad++ Rules syntax highlight
Replies: 23
Views: 12559

Re: Notepad++ Rules syntax highlight

Hello
It works my file was corrupted !!
Please note the new language appears after you reopen the program
Thanks
Patou
by Patou
03 Nov 2021, 23:02
Forum: ESP Easy: General Discussion
Topic: Notepad++ Rules syntax highlight
Replies: 23
Views: 12559

Re: Notepad++ Rules syntax highlight

Hello Grokvillen, Hope you are still with us .... I installed on a new computer the latest notepad++ 8-1-9 I used the esp easy language on my previous computer and found it very usefull. (disk crash and dead!) Downloaded the zip file on github and change it to .xml but the import failed. Is this ver...
by Patou
05 Sep 2021, 23:19
Forum: ESP Easy: Software
Topic: Strange behaviour with unixtime and dummy variables
Replies: 3
Views: 4825

Re: Strange behaviour with unixtime and dummy variables

OK thanks
I put in the dummy variables the unixtime - (unixtime on 2021/01/01 00:00:00)
This can be saved on a float of 22 bit correctly and I can find back the last date and time before a warm reboot starting at begin of this year.
Patou
by Patou
05 Sep 2021, 21:13
Forum: ESP Easy: Software
Topic: Strange behaviour with unixtime and dummy variables
Replies: 3
Views: 4825

Strange behaviour with unixtime and dummy variables

Hello, I am currently using following release : ESP_Easy_mega_20210503_normal_ESP8266_4M1M on a Wemos D1 mini Loading unixtime in dummy devices at different times seems to give strange results ! Here is the test program : On start do TaskValueSet,8,1,%unixtime% // Store time oledframedcmd,1,"U:...
by Patou
11 Aug 2021, 22:47
Forum: ESP Easy: Software
Topic: Push button Dimmer
Replies: 12
Views: 8941

Re: Push button Dimmer

Hello Vitalik, Can you share your rules and the settings of the PCA9685 ? I do not understand what you mean with : "And I set the smoothness with the help of time and the divider coefficient" Using the dim duration on an pwm command of a gpio from the Esp 8266 stops the execution of the ru...
by Patou
08 Aug 2021, 23:09
Forum: ESP Easy: Software
Topic: Using New Web based flasher connection problem
Replies: 2
Views: 4406

Re: Using New Web based flasher connection problem

Hello TDer Thanks for quick reaction Indeed the unit was already used, and with another IP range So I flash the unit on the conventional way with the latest august firmware. Using this way, the unit shows up with his wifi network , I could connect and saw indeed that the static ip was out of range o...
by Patou
08 Aug 2021, 22:37
Forum: ESP Easy: Software
Topic: Using New Web based flasher connection problem
Replies: 2
Views: 4406

Using New Web based flasher connection problem

Hello, I tried the new web based flasher on chrome and downloaded the latest firmware. I took the 20210615_normal_Esp8266_4M1M. The download works fine but ... I do not find the wifi network of the unit like the one normally available at start. Connecting with serial monitor I get the messages : 127...
by Patou
08 Aug 2021, 21:09
Forum: ESP Easy: Software
Topic: Push button Dimmer
Replies: 12
Views: 8941

Re: Push button Dimmer

Sorry I put 2 times the same picture of the devices !!
by Patou
08 Aug 2021, 21:08
Forum: ESP Easy: Software
Topic: Push button Dimmer
Replies: 12
Views: 8941

Re: Push button Dimmer

Hello, Using the newly implemented lop timer msec, an external oscillator is not any more necessairy as you have programmed in your rules. It is now also possible to do indirect adressing and the number of variables is not any more limited to 16. So I have created a table with 20 values from variabl...
by Patou
20 May 2021, 01:26
Forum: ESP Easy: General Discussion
Topic: I2C Soil moisture sensor
Replies: 51
Views: 44871

Re: I2C Soil moisture sensor

Hello André,
I am really interested in your moisture sensor.
Did you manage to make it work ?
Patou
by Patou
02 May 2021, 18:12
Forum: ESP Easy: Software
Topic: Daily flash write rate exceeded! (powercycle to reset this)
Replies: 3
Views: 5848

Re: Daily flash write rate exceeded! (powercycle to reset this)

Hello Thanks for quick reaction. The command ResetFlashWriteCounter works but the power cycle did not work. For info: I had the load of the cpu quiet high (a long time up to 100%) and rule processing quiet long. Description #calls call/sec duty (%) min (ms) Avg (ms) max (ms) rulesProcessing() 30174 ...
by Patou
02 May 2021, 17:29
Forum: ESP Easy: Software
Topic: Daily flash write rate exceeded! (powercycle to reset this)
Replies: 3
Views: 5848

Daily flash write rate exceeded! (powercycle to reset this)

Hello I am using the latest version : ESP_Easy_mega_20210223_normal_ESP8266_4M1M. I got this message and, even after a power cycle, the message appears again when I want to save some modification. Please see below the storage data ( I do not understand all the lines !!) Storage Flash Chip ID: Vendor...
by Patou
23 Apr 2021, 13:25
Forum: ESP Easy: Hardware
Topic: GY-530 VL53L0X Laser Ranging Sensor Time-of-Flight
Replies: 76
Views: 34401

Re: GY-530 VL53L0X Laser Ranging Sensor Time-of-Flight

Hello
With this bin file : ESP_Easy_mega_20210308_normal_ESP8266_4M1M_VCC it works perfect.
Thanks for your work I will order a VL53L1X to test also the more sophistocated sensor
Patou
by Patou
22 Apr 2021, 01:56
Forum: ESP Easy: Hardware
Topic: GY-530 VL53L0X Laser Ranging Sensor Time-of-Flight
Replies: 76
Views: 34401

Re: GY-530 VL53L0X Laser Ranging Sensor Time-of-Flight

Hello, I am trying to use the plugin with a Gy 530 Vl51L0X but get the message on the serial log : VL53L1X: Sensor not found, init failed for 0x29 The i2c scanner recongnize the Gy530 on port 0x29. I am using the last bin downloaded from this post : Here is the serial log : INIT : Booting version: (...
by Patou
12 Apr 2021, 20:29
Forum: ESP Easy: Projects / Applications
Topic: ESPeasy - plugin for Shutters and Blinds
Replies: 6
Views: 12050

Re: ESPeasy - plugin for Shutters and Blinds

Hello
I realise an application for shutter with limit switch shutter closed, limit switch windows open and 2 buttons up and down
Please had a look at this post
viewtopic.php?f=4&t=8145
Have a nice evening
Patou
by Patou
26 Mar 2021, 21:10
Forum: ESP Easy: Software
Topic: SCD30 - CO2 sensor
Replies: 118
Views: 183302

Re: SCD30 - CO2 sensor

Thanks i can wait a little for this project
by Patou
26 Mar 2021, 17:13
Forum: ESP Easy: Software
Topic: SCD30 - CO2 sensor
Replies: 118
Views: 183302

Re: SCD30 - CO2 sensor

Hello
I am interested in the integration of this sensor but i am not clever enough to make my own bin file
Can someone send a bin file for 4 Mb esp that include this sensor
Many thanks in advance

Patou
by Patou
15 Mar 2021, 13:13
Forum: ESP Easy: Software
Topic: Indirect adressing
Replies: 8
Views: 5806

Re: Indirect adressing

ok thanks so 30 varaibles should not go to the memory limit
by Patou
15 Mar 2021, 12:43
Forum: ESP Easy: Software
Topic: Indirect adressing
Replies: 8
Views: 5806

Re: Indirect adressing

Sorry .. one more question what is really the limit of the number of variables ?
Can I make a table with 20 lines ( 20 variables) an still have 10 variables free = 30 in total ?
by Patou
15 Mar 2021, 10:36
Forum: ESP Easy: Software
Topic: Indirect adressing
Replies: 8
Views: 5806

Re: Indirect adressing

Thanks I can continue my project on this base
by Patou
15 Mar 2021, 10:24
Forum: ESP Easy: Software
Topic: Indirect adressing
Replies: 8
Views: 5806

Re: Indirect adressing

Hello Ath,
Thanks for your reply
On the latest firmware ESP_Easy_mega_20210223_normal_ESP8266_4M1M
This is working Thanks
Can you please explain what is the difference between [var#1] and %v1% ?
It should be nice to have in the doc an example of indirect adressing
Have a nice day
Patou
by Patou
14 Mar 2021, 21:19
Forum: ESP Easy: Software
Topic: Indirect adressing
Replies: 8
Views: 5806

Indirect adressing

Hello, I should like to include in the rules the possibility of indirect adressing. This should be used to read a small table for example 10 values stored in var#1 to var#10 The index could be stored in var#11 and the result in var#12 with following formula : Let,12,[var#[var#11]] // Table On system...
by Patou
13 Feb 2021, 10:07
Forum: ESP Easy: General Discussion
Topic: large numbers in variable
Replies: 4
Views: 4804

Re: large numbers in variable

Look at this post there is the answer
viewtopic.php?f=4&t=8149#p48722
Have a good day
by Patou
24 Dec 2020, 12:14
Forum: ESP Easy: Projects / Applications
Topic: 4way valve rules
Replies: 6
Views: 12258

Re: 4way valve rules

Hello There was a mistake in my previous code Here is the correction This should run OK The timer reset line must be out of the if/endif part !!! Have happy christmas Patou On System#Boot do let,1,40 // Setpoint low let,2,42 // Setpoint high let,3,1000 // Pulse time opening (msec) let,4,1200 // Puls...
by Patou
21 Dec 2020, 12:33
Forum: ESP Easy: Projects / Applications
Topic: 4way valve rules
Replies: 6
Views: 12258

Re: 4way valve rules

Nice that you understand the principle and could adapt to your application
Have good fun now....
by Patou
16 Dec 2020, 21:28
Forum: ESP Easy: Projects / Applications
Topic: 4way valve rules
Replies: 6
Views: 12258

Re: 4way valve rules

Hello, For the small pulse you can use longpulse_ms For the waiting time just a timer See bellow Attention not tested just for info ! Patou On System#Boot do let,1,40 // Setpoint low let,2,42 // Setpoint high let,3,1000 // Pulse time opening (msec) let,4,1200 // Pulse time closing (msec) let,5,60 //...
by Patou
16 Dec 2020, 10:51
Forum: ESP Easy: General Discussion
Topic: Help needed on automated curtain project
Replies: 11
Views: 18174

Re: Help needed on automated curtain project

@igrad Hello This is an interesting approch to manage the automation only in HA. Unfortunately, for me, my programming skill in HA is poor regarding my experience in Esp Easy. Advantage to keep automation in esp is that it can run alone without wifi, network and controller ! Is it possible to share ...
by Patou
14 Dec 2020, 23:37
Forum: ESP Easy: General Discussion
Topic: Help needed on automated curtain project
Replies: 11
Views: 18174

Re: Help needed on automated curtain project

Hello Delmeer, I try to make some suggestions on some of your proposals : Drawing with switches : - If these are momentairy switches 1 up, 1 down and 1 stop OK ... to save 1 input : Stop can also be made with up and down pressed together - if these are normal switches (on my shutter they are normal ...
by Patou
13 Dec 2020, 21:13
Forum: ESP Easy: General Discussion
Topic: Help needed on automated curtain project
Replies: 11
Views: 18174

Re: Help needed on automated curtain project

@ jgrad, Hello, Your ready made solution with dragon seems interesting. It has 2 relays and can be used to control shutters. But... how do you keep local control and send to HA or Domoticz the state changes done locally ? Indeed all shutters have limit switches inside ( needed to stop the motor at m...
by Patou
13 Dec 2020, 17:29
Forum: ESP Easy: General Discussion
Topic: Help needed on automated curtain project
Replies: 11
Views: 18174

Re: Help needed on automated curtain project

Hello I have made a project for shutter control . This is quiet similar to curtains. Differents things must be consider : - May shutter close when windows is open ? No ! so I need a switch to detect windows is open - I suppose the motor has is own open en closed limit switches but they are inside an...
by Patou
17 Nov 2020, 02:02
Forum: ESP Easy: Software
Topic: Send cmd via mqtt from Home assistant
Replies: 2
Views: 5807

Re: Send cmd via mqtt from Home assistant

Hello,
I also discover that firmware 'ESP_Easy_mega-20200426_normal_ESP8266_4M1M.bin' has the problem
but firmwares
- ESP_Easy_mega_20200812_normal_ESP8266_4M1M
- ESP_Easy_mega-20200310_normal_ESP8266_4M1M

have no problem !
by Patou
17 Nov 2020, 01:33
Forum: ESP Easy: Software
Topic: Send cmd via mqtt from Home assistant
Replies: 2
Views: 5807

Re: Send cmd via mqtt from Home assistant syntax

Finally found the correct syntax :
Need "xx" and not 'xx' !!

Code: Select all

    - service: mqtt.publish
      data_template:
        topic: 'Volet_Living/cmd'
        retain: true
        payload: "event,ha_start" 
by Patou
16 Nov 2020, 23:33
Forum: ESP Easy: Software
Topic: Send cmd via mqtt from Home assistant
Replies: 2
Views: 5807

Send cmd via mqtt from Home assistant

Hello, I do not find in the topics of this forum or in the doc the exact way to send mqtt data from home assistant using 'cmd' On a mqtt tracker I see the messages so mqtt is correctly configured. On Esp1 this is the configuration MQTT-configuration.png When I use the MQTT helper I can receive the m...