Search found 10 matches

by bojan
03 Jun 2019, 13:56
Forum: RFlink: General Discussions
Topic: R45 - 433MHZ Send Doesn't Work Anymore
Replies: 5
Views: 1681

Re: R45 - 433MHZ Send Doesn't Work Anymore

Stuntteam wrote:
26 Feb 2017, 15:11
check your email..
This is not how the public forum should work. Please share.
by bojan
12 Feb 2019, 20:17
Forum: ESP Easy: Software
Topic: rules for roller shutter on nodemcu+relays 2ch
Replies: 42
Views: 6426

Re: rules for roller shutter on nodemcu+relays 2ch

I'm a big fan of the ESPEasy, but for the shutters I would recommend the Stefan Bode's fork of the Tasmota.
https://github.com/stefanbode/Sonoff-Ta ... two-relays

Also, don't forget to protect the relay contacts (add snubber RC circuit)
by bojan
11 Dec 2018, 11:41
Forum: ESP Easy: Software
Topic: How to emulate push button switch to ground
Replies: 5
Views: 759

Re: How to emulate push button switch to ground

Yes, that is probably the simplest solution. Thanks a lot.
Bojan
by bojan
10 Dec 2018, 19:25
Forum: ESP Easy: Software
Topic: How to emulate push button switch to ground
Replies: 5
Views: 759

Re: How to emulate push button switch to ground

Thank you Thomas, that will probably do the trick. Just to be clear: I would like to parallel connect the ESP GPIO to the LED controller push buttons.
2018-12-10 19.13.39.jpg
2018-12-10 19.13.39.jpg (469.63 KiB) Viewed 734 times
Also, thanks for 3.3V tip. I will have to use the level shifter.
BR
Bojan
by bojan
10 Dec 2018, 13:07
Forum: ESP Easy: Software
Topic: How to emulate push button switch to ground
Replies: 5
Views: 759

How to emulate push button switch to ground

Hello! I would like to emulate a push button switch to ground. I can do that with this : pinMode(powerButton, INPUT); digitalWrite(powerButton, LOW); pinMode(powerButton, OUTPUT); // Pull the signal low to activate the power button delay(100); pinMode(powerButton, INPUT); // Release the power button...
by bojan
09 Oct 2018, 07:50
Forum: ESP Easy: Hardware
Topic: Faulty SDS011?
Replies: 8
Views: 1535

Re: Faulty SDS011?

Update:
Got another SDS011 and now I have PM2.5 arround 10, which is normal. Ali refunded for the faulty. ;)
by bojan
29 Sep 2018, 13:52
Forum: ESP Easy: Projects / Applications
Topic: ESPEasy to control air conditioners / heat pumps
Replies: 152
Views: 50119

Re: ESPEasy to control air conditioners / heat pumps

i've just checked my Panasonic AC remote with your Raw-IR-decoder-for-Arduino and it shows Panasonic CS protocol. Is this protocol supported? I can't find it. Hmmm, what is the actual model number of the unit? It is normally CS-E7PKR or similar. CS normally just means indoor unit. The most common P...
by bojan
28 Sep 2018, 09:05
Forum: ESP Easy: Projects / Applications
Topic: ESPEasy to control air conditioners / heat pumps
Replies: 152
Views: 50119

Re: ESPEasy to control air conditioners / heat pumps

Hi ToniA,

i've just checked my Panasonic AC remote with your Raw-IR-decoder-for-Arduino and it shows Panasonic CS protocol. Is this protocol supported? I can't find it.

Regards
Bojan

BTW, thank you very much for your work
by bojan
29 Aug 2018, 15:49
Forum: ESP Easy: Hardware
Topic: Faulty SDS011?
Replies: 8
Views: 1535

Re: Faulty SDS011?

Well, even with the HEPA filter on the intake, in my room, I get 80. If you check the luftdaten.info (all sensors are SDS011) you will see even in the center of the cities not more than 15.
Official value about 2km away is 5.
regards
by bojan
29 Aug 2018, 10:45
Forum: ESP Easy: Hardware
Topic: Faulty SDS011?
Replies: 8
Views: 1535

Faulty SDS011?

Hi all,

I've just got the SDS011 connected to the nodemcu with the ESPEasy mega 2.0. It works, but the values are very high, 60 to 100 for both variables. The air is clean and it should be near 0. Am I doing something wrong?

Regards