Search found 37 matches

by sobolkz
05 Jul 2022, 20:33
Forum: ESP Easy: Software
Topic: Suggestion to improve the MPU6050 driver
Replies: 9
Views: 4717

Re: Suggestion to improve the MPU6050 driver

mackowiakp wrote: 05 Jul 2022, 16:32 I was 3 times in Ukraine so I have not time to test FW. Will do it ASAP.
So, I'm from Kazakhstan, I'm looking about loosing Ukrainian independent, what about topic state?
Let`s don`t politise this forum.
by sobolkz
30 Jun 2022, 12:49
Forum: ESP Easy: Hardware
Topic: Sensirion SCD4X family modules
Replies: 44
Views: 13557

Re: Sensirion SCD4X family modules

After few days of testing I can say, that SCD41 CO2 measurements are equal with Senseair S8. But SCD41 more compact and can work directly with I2C at 3.3V instead separate MODBUS for S8 and 5V. It can help with sizie of final devices.
by sobolkz
27 Jun 2022, 05:26
Forum: ESP Easy: Hardware
Topic: Sensirion SCD4X family modules
Replies: 44
Views: 13557

Re: Sensirion SCD4X family modules

Ath wrote: 26 Jun 2022, 19:53 I have received a SCD40 module this week, will reserve a new plugin id for this, as it doesn't seem feasible to integrate with existing SCD30 code.
Edit: Reserved P135 Environment - SCD4x CO2, Temp, Hum.
Ton, perfect. I can help with testing.
by sobolkz
26 Jun 2022, 17:28
Forum: ESP Easy: Hardware
Topic: Sensirion SCD4X family modules
Replies: 44
Views: 13557

Re: Sensirion SCD4X family modules

I'm accepting congratulations, just received SCD41 module. SCD41.jpeg TD-er, seems that SCD30 plugin doesn't support SCD4x. I2C scanner report only device at 0x62 addres without definitions. I'll check with Arduino IDE and inform here. UPD: Module are working, Sparkfun SCD4x library was used https:/...
by sobolkz
23 Jun 2022, 17:02
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 38640

Re: Unable to run "max" firmware into a ESP-32 16MB

So, esptool was installed into venv, version v4.1 installed.
Flash was readed after it.
As I understand it isn't important now due to you last message :D
Let's accept the fact, that factory.bin firmware should be updated with latest version of esptool - only it can guaranty successful procedure.
by sobolkz
22 Jun 2022, 15:55
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 38640

Re: Unable to run "max" firmware into a ESP-32 16MB

Just as a test, can you make an image on Linux of this 16M node using esptool.py by reading the entire flash? And then flash this exact image again to another ESP unit? Also, can you compare the read image and the factory.bin file, upto the size of the bin file? The first 4k is probably enough. Jus...
by sobolkz
22 Jun 2022, 05:10
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 38640

Re: Unable to run "max" firmware into a ESP-32 16MB

Just as a test, can you make an image on Linux of this 16M node using esptool.py by reading the entire flash? And then flash this exact image again to another ESP unit? Also, can you compare the read image and the factory.bin file, upto the size of the bin file? The first 4k is probably enough. Jus...
by sobolkz
21 Jun 2022, 17:11
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 38640

Re: Unable to run "max" firmware into a ESP-32 16MB

All done with Windows.
But 3.9.2 flash download tool was used. And ESP_Easy_mega_20220527_max_ESP32_16M8M_LittleFS.factory.bin was successfully flashed.
2022-06-21 21-10-32 MAX ESP32 - Google Chrome.jpg
2022-06-21 21-10-32 MAX ESP32 - Google Chrome.jpg (101.12 KiB) Viewed 37468 times
2022-06-21 21-09-12 MAX ESP32 - Google Chrome.jpg
2022-06-21 21-09-12 MAX ESP32 - Google Chrome.jpg (33.15 KiB) Viewed 37468 times
by sobolkz
21 Jun 2022, 11:21
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 38640

Re: Unable to run "max" firmware into a ESP-32 16MB

Maybe esptool.py does have some option to not change the bin? As I see there is no such options, but this option can be interesting: By default, the serial transfer data is compressed for better performance. The -u/--no-compress option disables this behaviour. I'll try to use Windows as primary way...
by sobolkz
21 Jun 2022, 04:57
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 38640

Re: Unable to run "max" firmware into a ESP-32 16MB

TD-er wrote: 20 Jun 2022, 23:09 Do you have "don't change bin" checked on the Espressif download tool?
esptool.py does change the bin while flashing, based on what (it thinks) it detects
Hmm, I'm using Ubuntu. Will check with Windows soon.
by sobolkz
20 Jun 2022, 18:12
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 38640

Re: Unable to run "max" firmware into a ESP-32 16MB

Ath wrote: 20 Jun 2022, 16:44 Can you try the same using the 16M1M build of ESPEasy, instead of the 16M8M_LittleFS build?
Same result with 16M1M version.
by sobolkz
20 Jun 2022, 16:40
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 38640

Re: Unable to run "max" firmware into a ESP-32 16MB

No result: Each flashing ends with hardware power disconnection. You May's release: esptool -b 115200 --port /dev/ttyUSB0 write_flash --flash_freq 40m 0x000000 ./ESP_Easy_mega_20220518_max_ESP32_16M8M_LittleFS.factory.bin esptool.py v2.8 Serial port /dev/ttyUSB0 Connecting..... Detecting chip type.....
by sobolkz
20 Jun 2022, 09:31
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 38640

Re: Unable to run "max" firmware into a ESP-32 16MB

Are you able to collect the output via serial after flashing? Please also try to power cycle the unit, just to be sure it isn't something left in memory or left uninitialized. OK, will check this too. B.T.W. - is it applicable before flashing ESPEasy image to "clear" flash instead burning...
by sobolkz
20 Jun 2022, 08:18
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 38640

Re: Unable to run "max" firmware into a ESP-32 16MB

Ath wrote: 20 Jun 2022, 07:31
Be sure to flash the latest version via serial (using the .factory.bin), so the latest bootloader is flashed onto the unit. That should fix this. You can use the recently released 20220616 build available at Github releases page
Yes, sure. I'm flashing .factory.bin via serial in this situation.
by sobolkz
20 Jun 2022, 07:06
Forum: ESP Easy: General Discussion
Topic: Unable to run "max" firmware into a ESP-32 16MB
Replies: 46
Views: 38640

Re: Unable to run "max" firmware into a ESP-32 16MB

Hi all! Just found this topic. Same issue with Wemos D32 Pro. As reported at their site - my version with 16MB flash and 4MB PSRAM. But I'm also can't use any "max" builds. Checked with latest mega-20220616. Same bootloop after flashing. But instead old issue, reported by topic starter - I...
by sobolkz
14 Jun 2022, 11:18
Forum: ESP Easy: Hardware
Topic: Sensirion SCD4X family modules
Replies: 44
Views: 13557

Re: Sensirion SCD4X family modules

Are there boards available with this sensor? It seems to be hard to solder by hand. There is many more sellers at Aliexpress, which offers SCD4X as sensor amd ready to use modules: https://a.aliexpress.com/_9fPZY5 https://a.aliexpress.com/_Aqnk9b Price is equal for Senseair S8. Sparkfun offering mo...
by sobolkz
14 Jun 2022, 07:09
Forum: ESP Easy: Hardware
Topic: Sensirion SCD4X family modules
Replies: 44
Views: 13557

Sensirion SCD4X family modules

Hi all! Is here anybody, who does testing new Sensirion SCD4X modules with ESPEasy? As I understand new sensors are photoacoustic instead SCD30, which NDIR. Is new one using same data protocols?
by sobolkz
26 Apr 2022, 07:04
Forum: ESP Easy: Hardware
Topic: Wemos D32 Pro with Wemos TFT 2.4 shield, backlit issue
Replies: 4
Views: 4637

Re: Wemos D32 Pro with Wemos TFT 2.4 shield, backlit issue

Disable the GPIO32 pullup; Use GPIO32 pulldown feature or install an external 100K pulldown resistor. - Thomas Hmm, as I wrote before -all already checked. I think 10K pulldown resistor better than 100K. "Hardware" page GPIO " Default pulldown" setting feature wasn't successful....
by sobolkz
26 Apr 2022, 05:34
Forum: ESP Easy: Hardware
Topic: Wemos D32 Pro with Wemos TFT 2.4 shield, backlit issue
Replies: 4
Views: 4637

Wemos D32 Pro with Wemos TFT 2.4 shield, backlit issue

Hi all! Due to old discussions about GPIO states at deep sleep I'm searching way to control backlit as designed. As we can see at board scheme and display shield there is additional pin, labeled as TFT_LED: Shield.jpg Wrover.jpg It can be used for brightness limitation by PWM at GPIO32 or backlit te...
by sobolkz
24 Nov 2019, 12:54
Forum: ESP Easy: Software
Topic: ESP Easy and GPIO in deep sleep
Replies: 6
Views: 7802

Re: ESP Easy and GPIO in deep sleep

Hi, I need to send a LOW to the SET or RESET pin of the dust sensor in order to turn off the fan. But in sleep mode all GPIO pins are HIGH on the wemos. So how do i do that? Here is the pinout and infos of the dust sensor if needed: https://www.espruino.com/PMS7003 Hi! As described before (also in ...
by sobolkz
28 Sep 2019, 16:25
Forum: ESP Easy: Software
Topic: Senseair S8 plugin
Replies: 2
Views: 5142

Re: Senseair S8 plugin

Maybe even best to open an issue on GitHub, if it is still an issue after you've removed the task and added it again (and save the settings at least once) Done, issue #2636 was added. It's look like different issue from deep sleep (which was successfully fixed). I think we should close old discussi...
by sobolkz
28 Sep 2019, 14:57
Forum: ESP Easy: Software
Topic: Senseair S8 plugin
Replies: 2
Views: 5142

Senseair S8 plugin

Checked in mega-20190928. Then sensor was added in devices - new information was listed at the configuration page: 2019-09-28 17-36-53 ESP_Easy - Google Chrome.jpg But first section looks like explanation of values of second section parameters. Second section look's like some dummy settings with str...
by sobolkz
28 Sep 2019, 13:59
Forum: ESP Easy: Software
Topic: Wemos D1 Pro with Senseair S8 boot loops
Replies: 16
Views: 12464

Re: Wemos D1 Pro with Senseair S8 boot loops

Due to latest release checking (for desired commit) I was confused with latest situation - it's look like Senseair plugin was changed too - some additional information was added: 2019-09-28 17-36-53 ESP_Easy - Google Chrome.jpg And (or) it can impact, that no issues with deep sleep now: INIT : Booti...
by sobolkz
28 Sep 2019, 13:34
Forum: ESP Easy: Software
Topic: Send data to thingspeak
Replies: 40
Views: 35109

Re: Send data to thingspeak

Stupid question, but I can't find you ESPEasy actual version info.
Is it older than mega-20190830?
It's look like my issue with old releases and (or) TD-er explained issue with "named" request limitation.
If you version are older - try to update to mega-20190830 and check situation.
by sobolkz
26 Sep 2019, 04:51
Forum: ESP Easy: Software
Topic: Send data to thingspeak
Replies: 40
Views: 35109

Re: Send data to thingspeak

Yeah, this is correct. I am using DHCP, and the router is on the IP: 192.168.0.1, so this seems right. However today I have checked in terminal if I can ping the api.thingspeak.com. It seems I have 100% packet loss :D The IP, which my PC was pinging is: 52.22.86.23. Previously I have used the IP: 1...
by sobolkz
25 Sep 2019, 06:26
Forum: ESP Easy: Software
Topic: Send data to thingspeak
Replies: 40
Views: 35109

Re: Send data to thingspeak

Yeah, thought about that, but checked my Router, and no firewall is activated. DMZ is also disabled. For a quick test created a fresh guest wifi, but the connection error is still prompted. My connection looks like the following: I have a DOCSIS router, which is now set to modem mode, thus it is no...
by sobolkz
24 Sep 2019, 10:16
Forum: ESP Easy: Software
Topic: Wemos D1 Pro with Senseair S8 boot loops
Replies: 16
Views: 12464

Re: Wemos D1 Pro with Senseair S8 boot loops

Latest news - simple Arduino IDE sketch was checked, no issues with awaking from deep sleep. 60 seconds awake\600 seconds sleep cycle was used: Screenshot_9.jpg Going to 0 mean, that battery too low for S8 powering but int's so low for board, and data was transmitted before battery was disconnected ...
by sobolkz
24 Sep 2019, 09:44
Forum: ESP Easy: Software
Topic: Send data to thingspeak
Replies: 40
Views: 35109

Re: Send data to thingspeak

Did you test with the same core library used? Hmm...Hard to answer, because this issue wasn't in my investigation scope. It was expected, checked with different versions (which was tested for my main issue with Sensear S8) and closed for me with mega-20190830. Accordingly topic's issue - I can chec...
by sobolkz
24 Sep 2019, 05:56
Forum: ESP Easy: Software
Topic: Send data to thingspeak
Replies: 40
Views: 35109

Re: Send data to thingspeak

Same issue was expected in some last versions of ESPEasy. No issues in mega-20190830. I can use IP address AND name api.thingspeak.com.
Try this version.
by sobolkz
16 Sep 2019, 10:10
Forum: ESP Easy: Software
Topic: Wemos D1 Pro with Senseair S8 boot loops
Replies: 16
Views: 12464

Re: Wemos D1 Pro with Senseair S8 boot loops

By the way - little difference between Senseair S8 and PMSX003 plugins. As I understand there is same Modbus connection plugin was used, but if PMSX003 was used - it's look like no any checks for it's state was used. If it isn't connected - no any timeouts, errors etc. in serial log. May be it can h...
by sobolkz
14 Sep 2019, 10:18
Forum: ESP Easy: Software
Topic: Wemos D1 Pro with Senseair S8 boot loops
Replies: 16
Views: 12464

Re: Wemos D1 Pro with Senseair S8 boot loops

grovkillen wrote: 14 Sep 2019, 09:29 Please observe that the S8 is not built for deepsleep. You would want to have the LP8 for that.
Yes, sure. Also, as I know - there is no sleep mode support in PMSX003 plugin. I'll add MOSFET key for it with free GPIO.
by sobolkz
14 Sep 2019, 05:48
Forum: ESP Easy: Software
Topic: Wemos D1 Pro with Senseair S8 boot loops
Replies: 16
Views: 12464

Re: Wemos D1 Pro with Senseair S8 boot loops

Can you make an issue for it on GitHub? Done, issue #2616 was reported. P.S. no any additional information. Problem can be reproduced at 100% if test scheme was created with Wemos D1 mini Pro, SH1106 framed plugin, I2C BME280 and active Senseair S8 plugin. If plugin wasn't enabled after task adding...
by sobolkz
13 Sep 2019, 15:47
Forum: ESP Easy: Software
Topic: Wemos D1 Pro with Senseair S8 boot loops
Replies: 16
Views: 12464

Re: Wemos D1 Pro with Senseair S8 boot loops

TD-er wrote: 13 Sep 2019, 12:59 I will look into this issue.
Can you make an issue for it on GitHub?
Perfect. Will wait you results.
I'm not registered at GitHub, but I'll register tomorrow morning and add this.
by sobolkz
13 Sep 2019, 12:05
Forum: ESP Easy: Software
Topic: Wemos D1 Pro with Senseair S8 boot loops
Replies: 16
Views: 12464

Re: Wemos D1 Pro with Senseair S8 boot loops

Is the reported value of 2700+ ppm realistic? Apart from that, can you please summarize it a bit? Also please give the following info: - RX pin - TX pin - How is the sensor powered? (is the voltage dropping when the S8 starts a measurement and the ESP boots + starts the WiFi connection?) - Was it w...
by sobolkz
12 Sep 2019, 17:05
Forum: ESP Easy: Software
Topic: Wemos D1 Pro with Senseair S8 boot loops
Replies: 16
Views: 12464

Re: Wemos D1 Pro with Senseair S8 boot loops

Yes, sure. it was checked too. Same problem with HW serial (with disabled serial logging) connection and SW serial connection (for example GPIO14&GPIO12). As you can see such boot loops can be reproduced only if S8 device was activated (you can find it's SN). Also this boot loops will going up i...
by sobolkz
12 Sep 2019, 16:50
Forum: ESP Easy: Software
Topic: Wemos D1 Pro with Senseair S8 boot loops
Replies: 16
Views: 12464

Wemos D1 Pro with Senseair S8 boot loops

Hi all! There is strange situation with Senseair S8 plugin support at least it past releases with Wemos D1 Pro board. Now I'm using mega-20190830, problem was fully investigated - then S8 sensor was added and deep sleep was activated board could not be fully booted. Board was going sleep after about...