I uploaded various software but none of them worked, the only one is the one from the post above, it reads but in a language I don't understand.

Welcome back. I'm trying to read the codes from my air conditioning again, but they don't show up in any way. Only RAW codes are read... I do everything according to the previous descriptions, but I can't do it. IRSEND,RAW2,^57^38*2B^16BCDABDBCBDB^17BDB^16B^17BCBCBDBD*3BCB^17*3BCBD*6BCC^17B^17B^16*5...

Hello Some time ago I bought such flood detectors: https://a.aliexpress.com/_B054f3 Now my question about uploading and configuring mega espeasy. I would like to combine them with Domoticz, maybe someone has encountered or met with such sensors. A low battery alarm would be useful and how to set the...

Hello, because of the multitude of topics I forgot but thank you for the answer. Tomorrow I will try to check your suggestions. I'm just surprised that the software works on Tasmota.

511/5000 Hello I have a problem with two systems, I installed an active buzzer on them, I connected it to the ground, + from the buzzer under GPIO12 in NodeMCU, exactly the same in the second system so that the Wemos D1 mini but + under GPIO14 and created in Espeasy - "Switch input - Switch &qu...

Load resistor I chose at 330 ohm and the indications are quite good though it combines if anyone would make this circuit with an amplifier.

I am asking for ADS1115 power supply because I do not know if the readings are getting stronger. When I connected SCT-013-030 0-1V it shows nothing when I connect SCT-013-100 0-50mA it shows readings.

the system is built and is very good compared to what I had to fight with the selection of R load. My one loop up to 100A has 105 ohm and the other and the other loop up to 30A has 33 ohm. When I connected this 100A and connected the 5W led bulb, I have indication 3-4 and when I connected the 100W b...

However, I will test your schematic, 10Kohm resistors, BAT diodes and 4.7uF capacitors, I already have only thought about using my loops, I will only remove resistors from them because it is possible. what should I mount a resistor on Load ??

Thank you very much for your help and what do you think about buying 3 pieces:
https://a.aliexpress.com/fmQn2vB91
I would break out loops that are there and connect my ones only remove the resistor that is in my loop?

Did you realize that the SCT-013-030 is a transformer? The output is AC, not DC. The ADS1115 isn't able to work with AC. It will measure at a random point of the sine wave resulting in changing values. The Circuit you showed is made for AC capable sensing. I'd use a bridge rectifier made from Schot...

it's a pity because I have to make such arrangements for 3 entries. The housing is starting to get big.

I will ask you, are the diodes alone enough and plug them into my circuit just to straighten the voltage from the transformer?

Oooo, you surprised me and it's very, I don't know much about electronics but I will try. I just wonder how these projects that are shown on the internet work, no one has straightened this tension in the projects shown. They also show that they measure alternating current. Thank you very much.

538/5000 I uploaded the latest version of ESPEasy to NodeMcu, I connected the ADS1115 to this, of course, I connected the loop with resistors according to the scheme. Only I have a problem with the indications, I can't calibrate it because the indications from the loop SCT-013-030 float very much un...

Commands depending on the possibilities:

IRSEND, WHIRLPOOL_AC, 830604620000922D0000000000D900010000080009,168

or

IRSENDAC, { 'protocol': 'WHIRLPOOL_AC', 'model': 2, 'power', 'he', 'mode' 'cool', 'Temp': 22, 'swingv' 'off', 'swingh' : 'off', 'light', 'on'}

You helped me a lot, thank you very much. My air condition transmits in WHIRLPOOL_AC code. As I set in heat pump mode and chose the Hisens protocol, nothing happened. I switched to the IR transmitter, connected the IR receiver and sent the command from the remote control in the log showed first the ...

I have Hisense air-conditioning and in the P035 coding it is not in the description, but it is in P088 but it is there as a heat pump, how to run such a plugin to test it ?? Thank you for your interest

Hello I made a remote control based on Wemos + Ir Led (PCB0100) + Ir Receiver. I uploaded a soft Tasmot into it and read the TV remote control code from the console: { "IrReceived": {"Protocol": "NEC", "Bit": 32, "Date", "0x0202B24D"}} afte...