Yes the same when i would reset some modules didnt reset with the webgui only hard reset or i update the same firmeware

Hallo i have made my own homeautomatic system for lightswitches, temeratur, heating, shutter. If the esp modules with the espeasy arrives around 49 days the switches doesnt switch the lights on and in the webgui i doesnt see that the switches switches from 1 to 0. When i reset the modules then all o...

With invers its the same

No isn't invers

On Action: http://192.168.1.170/control?cmd=GPIO,5,1
Off Action: http://192.168.1.170/control?cmd=GPIO,5,0

Hallo i have a problem with the release 148 My rule: On Tur_Schalter#Switch do If [Relay#State]=0 Gpio 5,0 Else Gpio 5,1 Endif Endon on toggle do if [Relay#State] = 0 GPIO,5,0 else GPIO,5,1 endif Endon On domoticz i call the relay with ip call. My problem is with this rule on r135 all ok i can turn ...

Arduino: 1.6.12 (Windows 10), Board: "Generic ESP8266 Module, 80 MHz, 40MHz, DIO, 115200, 512K (64K SPIFFS), ck, Disabled, None" c:/users/acer/appdata/local/arduino15/packages/esp8266/tools/xtensa-lx106-elf-gcc/1.20.0-26-gb404fb9-2/bin/../lib/gcc/xtensa-lx106-elf/4.8.2/../../../../xtensa-l...

Grüß Euch aus AT
Ich hab alles mit domoticz gelöst.
Licht, rolläden, wetterstation mit eigenen Platinen die unter den Unterputzschalter kommen
Mfg Michael
Hab eh schon ein paar Fotos eingestellt

Hallo i have rebuild your profect. Great! I have 2 bugs the the Gust in the wind device the value is not the same as on the display! I must put this %value%*3.6 in formula field and now is ok! And on domoticz all sensors display the value but the wind have no icon and when i go to protocol the side ...

hallo is it posible that i get a temp from domoticz to my espeasy so that i could display it on my oled ?? with a variable in the setup for the oled display

thank you it works!!!!!!

My esp12 reseted after i2c INIT : Booting Build nr:120 IP : Static IP :192.168.1.11 WIFI : Connecting... 1 WIFI : Disconnecting! WIFI : Connecting... 2 WIFI : Disconnecting! WIFI : Connecting... 3 WIFI : Disconnecting! INIT : I2C ets Jan 8 2013,rst cause:4, boot mode:(3,6) wdt reset load 0x4010f000,...

Oh no thats not good i cant change all my switches thats to expensive!! That was not so a good idea with the rules from the programmers!! Ok then i let my esp on R095

Hallo i use the esp for my homematic i have the r095 on it. Inputs are two switches for the two lights and two outputs to switch the lights on. I work with a raspberry pi with domoticz on it. With r095: the switches are of and i would turn on with my handy. the light switch on Ok thats what i will! ...

I dont come in the gui
The esp resets every 4 sec

I would test the miniproextender on gpio5 and then the esp crash

Hallo my esp didnt function! in the serial monitor the esp says : ets Jan 8 2013,rst cause:4, boot mode:(3,7) wdt reset load 0x4010f000, len 1264, room 16 tail 0 chksum 0x42 csum 0x42 ~ld ªU INIT : Booting Build nr:48 WIFI : Connecting... IP : Static IP :192.168.1.220 INIT : I2C ets Jan 8 2013,rst c...

no i have only esp-12e ihave them flash also with 512k:( that was my problem

it comes up and the old version number stand there! In the Settings are the old one now i have found the Problem i think: 1. when i flash the r070 with 4M(SPIFFS 3M) with the Flashertool (I have make it always with 512k (64k SPIFFS)) 2. Make the .bin File also with 4M(SPIFFS 3M) And now when i OTA t...

Hallo from Austria. i have only 12E Moduls. 'I testet the OTA Firmware update on them and all FAIL!! The esp after reboot say Log 688 : INIT : Booting Build nr:70 1577 : WIFI : Connecting... 1 5592 : WIFI : Connected! 5593 : INIT : I2C 5595 : INIT : Boot OK 5595 : INIT : Reboot from deepsleep 35596 ...

Hallo from Austria
I will display my Thermostat from domoticz on the display
Is there any way to diplay the thermostat Temperature?
Best regard

Thank you i have now seen in the releasnots

Hallo i have found on github only r048 where could i get the r60? I couldnt found the version
Best regard from austria

Hallo i have the same problem from kr0815! I have uploaded the r048 software on my 6 esp01. Ihave them config with static ip and my wifi ssid with no password. I reset the esp it dont login my wifi ap-wifi opens again! When i disconect in the tools and then conecting, then the ap-wifi is gone and th...

Hallo i have the same problem from kr0815! I have uploaded the r048 software on my 6 esp01. Ihave them config with static ip and my wifi ssid with no password. I reset the esp it dont login my wifi ap-wifi opens again! When i disconect in the tools and then conecting, then the ap-wifi is gone and th...