Let's Control It

ohaldi

Thanks so much that you will fix this problem, you help is appreciated
ESPEasy is really a very good Firmware.
Small question : may I use this same file for one ESP8266 and ESP32?

I have a test board D1 WEMOS with one ESP-8266

ohaldi

Hello, I don't understand why, with ESPEASY, I always have problems obtaining a quick and simple first connection after flashing with ESPEASY Web. Here's the link I used with Microsoft Edge. https://td-er.nl/ESPEasy/ After installation complete!, Logs & Console, Connect to Wifi, Configure Wi-Fi,...

ohaldi

Just for information. I just received the same card and took the opportunity to do some additional tests. If I erase all the ESP32 software and power up the board. Then the relays have absolutely no reaction. As soon as I download ESPEasy, without any configuration, then again I have this problem wh...

ohaldi

Thank you very much for your help.
I also tried setting the GPIO boot states to Output Low, but that didn't solve my problem.
I will try to put a small capacitor between pins 16 and 17 to ground.

ohaldi

Hello I'm using the following board : Two Canal ESP32-WROOM-32E. See Picture. ESP32-WROOM-2Relais.jpg I use it to close my garage door if it's left open. I use a relay that sends pulses to open or close the door. The problem is when the boot card the two relays make a small pulse. In my case, this a...

ohaldi

Can you try setting the WiFi on ESPEasy to b/g mode only? (tools->Advanced page) And also check the last options "Extra Wait WiFi Connect" and "Enable SDK WiFi Auto Reconnect" Thanks, this seems to be the best solution. I'll continue my project and see if the WIFI connection wil...

ohaldi

I flashed the version mentioned above. But I still have a connection problem. wifidisconnect >wifidisconnect 175831 : Info : WiFi : WifiDisconnect() 175946 : Info : WIFI : Disconnected! Reason: '(1) Unspecified' 175947 : Info : WIFI : Arduino wifi status: WL_NO_SHIELD 255 ESPeasy internal wifi statu...

ohaldi

OK, then I will try the following version : 20231013 Norm 4M [ESP8266,ESP32,ESP32-S2/S3/C2] is this correct?

ohaldi

Hello I have just bought the following card: ESP32_Relay X2 (ESP32_WROOM_32E) With the help of EDGE and the following link (https://td-er.nl/ESPEasy/), I installed the latest version of ESPEasy: Normal 4M ETH [ESP32]. The installation was successful. After that, I was also able to access with the DH...

ohaldi

Thanks for your help. I disabled the 5GHz wifi. Now it's ok. I will read about band steering and IGM snooping with my RUTX10 Router. I've turned on and off some other switches whose exact rules, I don't know. I have some ESP8286s with ESPEasy, but would like to know more about ESP32s. However there ...

ohaldi

Dialog, used Termite: OK 243325 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: DISCONNECTED 243326 : Info : WiFi : WifiDisconnect() 243430 : Info : WIFI : Disconnected! Reason: '(1) Unspecified' 243531 : Info : Reset WiFi. 243534 : Info : WiFi : Start network sc...

ohaldi

Many thanks for your feedback. I allways have had problem with the first Wifi connection. I'm just testing on a single ESP-WORM-32 the last firmware from ESPEasy "ESP_Easy_mega_20230822_normal_ESP32_4M316k_ETH.factory.bin" What you can try is to connect using a serial terminal and enter th...

ohaldi

Hello, I'm happy to test the new version. With the latest version "mega-20230409" flashed on an ESP-WROM-32 using "flash_download_tool_3.9.5.exe" I encountered the following problem. I first flashed the following bin "ESP_Easy_mega_20230822_normal_ESP32_4M316k_ETH.factory.bi...

ohaldi

Sorry I forgot to telle you that I have the following code on the top of my Rules:

Code: Select all

on System#Boot do
timerSet,1,3
endon

What I don't understand with ESPEasy is why I don't see any communication if I use an MQTT Viewer on my Brocker.
I see only for every ESP : status/LWT Connectet.

ohaldi

many thanks for your help. - Yes the Domoticz MQTT Protokol is Enabled. I see the value in Domoticz. - Yes the Controller Subscribe: Domoticz/in and Controller Publish: Domoticz/out ist ok. I think that if I had made a mistake, I wouldn't see the values in Domoticz! ESP_3.png I also tried to add the...

ohaldi

Hello, I have some ESP who communicate with a brocker. With Domodicz I get the Temp + Humidity + Baro ESP_1a.png With the help of Windows APP MQTT-Explorer I don't see those values! ESP_2.png I have one ESP with TASMOTA and here every thing work well. Do I have to add a command in the rules to get t...

ohaldi

I have read your idea on the basis of Dummy variables. And this was the right solution for me. Thanks again. Devices.png The script has also become simpler with the Dummy variable. on System#Boot do TaskValueSet 5,1,10 AsyncEvent,PIR#State=[PIR#State] // Let the PIR eventhandler take care of the log...

ohaldi

OK, I'm going to change in the future to pull-up. I found this example somewhere on the web. I also realized my logical error. In fact, with the on / endon command, this is only executed when there is a change, not all the time. This is the reason why my if "If [Delay#State]=0" inside is n...

ohaldi

Thanks again for your patience with my problem.
Yes, I have a resitor with 4.6kOhm. But pull-down.
Like this :

: Device-Delay-Pull-Down-Resistor.png (30.62 KiB) Viewed 1771 times

I changed the GPIO-17 to GPIO-25 and GPIO-14 to GPIO26.

: Device_b.png (44.35 KiB) Viewed 1771 times

But I still have the above mentioned issues!

ohaldi

Here the entire rules? on System#Boot do AsyncEvent,PIR#State=[PIR#State] // Let the PIR eventhandler take care of the logic endon on Door#State=0 do // Door is open event,Progress LCD,1,1,"" LCD,2,1,"Die Tor ist offen" If [Delay#State]=0 // Button Delay LCD,4,1,"Pause AUS&q...

ohaldi

Yes, I would like it to work always. I don't think the variant with "taskvalueset" is the best. I'm new to EspEasy, I have the impression that the "taskvalueset" function changes a memory value and not the value stored in the GPIO14. I set the button connected to the GPIO14 to &q...

ohaldi

Many thanks for you help. I checked the following box: AllowTaskValueSet on all Plugins: At the end of my rule I have now added the line : ... On DOOR#State=1 do // Door closed lcdcmd,clear LCD,2,1,"Die Tor ist zu" TimerSet,1,0 // Stop Loops TimerSet,2,0 // Stop Repeat taskvalueset,6,1,0 E...

ohaldi

Hello, I have a switch of type "push button active high" named "DELAY" on the GPIO-14. When I press this button, I change a "state" value from 0 to 1 or vice versa. How can I also set this "state" value to 0 using a ruler? I tried with: 1. DELAY#State=0 2. GPI...

ohaldi

Thanks for you quick answer. OK I will re
For my first ESP (Sender), I have the build 20103
and the second one (Receiver) has the build 20116.
I have already been to the link you mentioned. So I will read this document again.
But I don't understand how the receiver chooses his source.

ohaldi

Hello pawell32, I followed your comment : On ESP_Balkon you should now open the BMx280 device page (Edit button), and enable the P2P controller. If it was already enabled, disable it, submit, then enable, and submit again. This last submit action should send it to the ESPEasy P2P network NB: It woul...

ohaldi

After several manipulations, I suddenly saw my ESP on the WIFI network of my mobile. In fact, I first used the WIFI receiver from my PC, which did not see it. Then I was able to configure ESP Easy to connect to my network. What I also did according to a video on youtube, I first flashed the binary: ...

ohaldi

Hello I am trying to flash ESPEasy on an ESP-WROOM-32. I followed the various instructions found on the net and on the Let's Contl It website. For that I’m using the version 3.9.3 from Espressif. I’m tried the following binary version: ESP_Easy_mega_20220616_normal_ESP32_4M316k.factory.bin or ESP_Ea...

ohaldi

I found the following solution without PIR activation. // -------------------------- // Project : Garage door management with an ESP8266 // Last Change : 29.07.2022 /Ho // GPIO17 Door State // GPIO02 Button lond Timer / 20min // GPIO13 Relay Door closing pulse // http://192.168.90.97/control?cmd=eve...

ohaldi

Hello I made a quick test board. Everything is on a good way. I am starting to understand how the rules work. It's really good but not evident. I also used a Display with 4x20. Your example works well. However if the door is opened and there is no PIR movement, the progress bar does not start and at...

ohaldi

Once again a big thank you for your idea. I will build a box with the components soon.

ohaldi

Once again, many thanks for your help. My idea is to close a garage door automatically after a given time. In fact, there will be two GPIO inputs. One to know if the door is already closed. Here the ESP does nothing. Only show on the LCD that the door is closed. If the door is open, then the progres...

ohaldi

Many thanks for your help. The rules are new for me.
Can you please help me again how to start the progress bar using a GPIO input (PIR sensor) and know if the progress bar has reached 100%?

ohaldi

Hello. I want to display a progress bar. In my case I use a 16x2 LCD. I would like each character (star) to display a 10 second delay. However, I would like my two buttons to remain active while the progress bar is displayed. Does anyone have an example? it would be nice if the character was a block...

ohaldi

Just for your information:
After months of research. I sold my ASUS RT-AX86U router. I replaced it by the model of teltonika, the RUTX10.
That solved all my WIFI communication problem. Don't ask me why. I don't have the knowledge for that.

ohaldi

>You did many changes at once, that's usually not the best method to actually pinpoint the issue.
In fact I Turn off [Enable Smart Connect] only this option.
The another one were already on Disable.
In the next few days, I'll try to set these options to Enable and see if it makes a difference.

ohaldi

OK, I did the following on my ASUS RT-AX86U: -Go to [Wireless] > [General] page. Turn off [Enable Smart Connect] and select the [Band] for your network devices. -Disable [802.11ax / WiFi 6 mode] -Disable [Wi-Fi Agile Multiband] -Disable [Target Wake Time] -Disable [Protected Management Frames][/i] I...

ohaldi

I’m using many ESP8266 mainly with ESPEasy (sometimes Tasmota). These ESP are connected to my ASUS RT-AX86U Router. I don't understand why I lose my connections with some of them very regularly. On my 10 pieces, 50% are often lost. I have added reboot scripts mainly on the ESPEasy if it had no conne...

ohaldi

OK and many thanks for your help

ohaldi

As I said, I used the following file: ESPEasy_ESP82xx_mega-20211105.zip
how can I check the SDK Version ?
or what do you mean with SDK ?

ohaldi

Thank you for your help. What I did: 1 Deleted my old Arduino and all directories with the Arduino name. 2 Installed the latest version of Arduino 1.8.16 3 From the last file ESPEasy_ESP82xx_mega-20211105.zip - Copy the directory source\src in a local directory, in my case D:\Arduino\Dev_ESPEASY\ESP...

ohaldi

Hello I'm using the following link to update the library's:
http://arduino.esp8266.com/stable/packa ... index.json
If I have a problem I delete the lib and then reinstall it.

ohaldi

Hello, I can't compile with the help of Arduino V1.8.16 the ESP version (mega-20211105). I still have a problem with the Servo scripts. I removed the library, made a new installation. But nothing works. I get the following error messages: In file included from D:\Electronique\Arduino\DEV ESPEasy-meg...

ohaldi

I thank you for your help. I will follow the changes.
Congratulations again to the development team of this software which is very intuitive.

ohaldi

Hello, Many thanks for all your information. I alredy tested the last version from ESPEasy-mega-20210223, but also without success. I just tested to compile my source version from 04.02.2020 with the help of Arduino. The compiled version is OK. I also changed to a fixed IP address in the custom.h fi...

ohaldi

Hello, I could upload the firmware : ESP_Easy_mega-20200426_normal_ESP8266_4M1M.bin to my D1Mini ESP8266. After a reset, I also could connect to the IP 192.168.4.1. I changed the SSID and set the password. The problem after 20s nothing append. I'm still on the IP 192.168.4.1. What are the possible c...

ohaldi

Just to be sure, the nightly builds are here: https://github.com/letscontrolit/ESPEasy/releases I just looked at the ZIP file: ESPEasy_ESP82xx_mega-20201130.zip Inside the bin directory there are numerous builds with "test" in the name, like: ESP_Easy_mega_20201130_test_ESP8266_4M1M_VCC.b...

ohaldi

Many thanks for your quick answer. If I understand correctly, testing is not included in the .bin! In the meantime, I compiled the source of ESPEasy with Arduino. I have no errors. The .bin point is generated correctly. I added two plugins in the define_plugin_sets.h file #ifdef PLUGIN_SET_TESTING #...

ohaldi

Hello
I downloaded the ESPEasy_ESP82xx_mega-20201130.zip.
They are about 36 .bin files
I'm like to use the Nextion NX4024T032_011 Display. In with .bin version is the plugin included?
Regards
Otto

ohaldi

Work well.
Many thanks for your help
Otto

ohaldi

Hello Thomas,
Yes the if must be "on".
Now I have to complete my script. When I press 4 seconds, it puts a delay of 25 sec.
But if someone moves the PIR it puts the delay back to 5 sec.
Regards
Otto

Search found 61 matches