Let's Control It

sawo

@xmenne

I am also planing to use the cable V2 sensor for my gasmeter.
on which GPIO port did you connect the sensor on the wemos?

thx
sawo

sawo

Hi TD-er,

sorry that was a copy / past issue.
I will take a look at looptimer.

Thx
sawo

sawo

Hi, I finally got the time to rework my setup, the proximity sensors are now configured as endpoint swichtes! :) As aspected I have some problems with my rules, maybe any one of you can assist my or give me a hint. Sorry for the maybe basic and stupid questions! First off all I want the rule to work...

sawo

Hi Ath,

okay I will change my setup and use the inductive proximity sensor as endpoint switch.
ThX

Sascha

sawo

Hi, this is hard for me to explain.... (english knowledge) but I will give it a try. The RC_Solar and _Normal are "LJ12A3-4-Z/AY inductive proximity sensor/switch" these are used as an endpoint of a 3 way ball valve. 3way.jpg Pumpe_Normal / _Solar are replays which control the motor to tur...

sawo

Hi Ath :D it doesn´t turn on the GPIO 12 port. (else) Yes it is configured in the devices tab and works fine. when use cmd GPIO,12,1 / 0 all other devices also work fine. devices.JPG This is my complete rule: On RC_Normal#State=0 Do GPIO,14,0 TaskValueSet 7,1,0 EndOn On Schalter_Normal#State=1 Do if...

sawo

Hi all,
I hope anyone could help me with my rule.
It won´t start.

On Schalter_Solar#State=1 Do
if [RC_Solar#State]=0
GPIO,12,0
TaskValueSet 6,1,0
else
GPIO,12,1
EndIf
EndOn

The only thing which is set is the "TaskValueSet 6,1,0".

thx
sawo

sawo

Hi Ath,
everything works fine for me!!!!
Thanks a lot for your help, hope to finally to complete my project!!!!

Sawo

sawo

Hi Ath,
will try it tomorrow.
Thanks a lot for your assistance.

Sawo

sawo

Hi Ath,
thx works for me so far!!!
Is it possible to get the status of each relay seperatly?
Instead of in one state.

thx
sawo

sawo

Hi Ath,

I updated my wemos with your version.
The relay modul is conencted and recognized.
But how do I controll them?
What is the command?

Regards
Sascha

sawo

Hi Ath,

sorry I was quite busy in the last days.
No I didn´t had the time to test ist yet. But will do in the evening.
Thanks so far!
Sawo

sawo

Ath wrote: ↑18 Nov 2021, 09:38 There will be some more options, like initial state of a relay, and also an output value holding the current state (as a bitmap), that can optionally be sent to a Controller.

PERFECT exactly what I was looking for!!!!
Thanks so much

sawo

Ath wrote: ↑17 Nov 2021, 22:34 There is a start already:

Screenshot - 17_11_2021 , 22_32_08.png

Most important still to do though, command handling

this looks promising

sawo

@ATH

sorry haven´t read your previous post.
Thanks for your info and your effort!!!!
I try to be patient.

sawo

sawo

I hope that it is okay to post the web link IF NOT PLEASE DELETE
https://wiki.seeedstudio.com/Grove-4-Ch ... PDT_Relay/

sawo

Hi all, thanks a lot your your answers. I have decided to use a separate Wemos D1 since I changed my plans, to get my pool solar Control to work. But now I have a different problem, I bought a 4 channel SPDT relay v1.0 board from seeed, this connects via I2C interface. My problem now is that it is n...

sawo

Hi dynamicdave,
thanks for your answer, so in this case I think I will use a seperate wemos to controll the relays.
Thanks
sawo

sawo

Hi all,
I hope you can help me with my current issue.
I need to connect 2 more relays to my wemos d1 mini runnig espeasy.
The only GPIO ports which are free / not used are GPIO 0/1/2/3/15
Which ones would you use to connect a relays?

thx
sawo

sawo

Hi grovkillen,

do you think you can help me again with this rule?

I want to have a short delay of 30sec, before the fan turns on, when the lux value is greater then 100.

How can I realize this.

thx
sawo

sawo

hi grovkillen,

thanks alot for your help again!!!
It works!!!

Thanks

sawo

Hi all, could any one please assist me with a espeasy rule? I would like to setup an bathroom ventilation rule, so when the lux value is above 100 and/or the humidity is above 65 the fan should turn on and stay on for 5min. I am using a wemos d1, dht22 and a bh1750. This is the rule I have to far: b...

sawo

Hi TD-er,

okay I'll take it apart and see what's in it.

THX

sawo

Hi all,

do you think it is possible to use an old lcd display from an thermometer, such as this one (see attachment) to controll it via an esp?
I want to show the temperatur from the aquarium.

Regards
Sascha

sawo

@grovkillen
thanks a lot for helping, I have created an issue.

sawo

Hi grovkillen, thanks a lot for explaining. But the issue still exists, I think that the interval of the RDM6300 is set to high. When I quickly put the tag on and off it only swichtes once, but if I old it on for about a 1/1,5 second it will switch 2 or more times. Is there a possibility to pause th...

sawo

Hi grovkillen,

thanks a lot for helping me.
One question, what does the [VAR1#!Z] stand for, do I need to create a variable or device?
When I copy your rule nothing happends, what do you need to know from my setup?

thx

sawo

here you go.

on water_on do
gpio,4,1
endon

on water_off do
gpio,4,0
endon

on rfid_tag_water#Tag do
timerSet,1,2
if [water_pump#On]=1
event,water_off
else
event,water_on
endif
endon

THX

sawo

Hi grovkillen,

sorry that makes no difference.
Even when I remove this part of the rule:
On Rules#Timer=1 do
TaskValueSetAndRun,1,1,-3342336
SendToHTTP 192.168.1.10,8181,x.exe?Antwort=dom.GetObject("Tag").State(0)
endon

it still switches twince or even more often.

Sawo

sawo

So now it tested my new rules: on water_on do gpio,4,1 endon on water_off do gpio,4,0 endon on rfid_tag_water#Tag do timerSet,1,2 if [water_pump#On]=1 event,water_off else event,water_on endif endon On Rules#Timer=1 do TaskValueSet,1,1,0 endon but when I hold the token on the reader it always switch...

sawo

Hi TD-er, I have removed it, now it will reboot after 44 seconds. Maybe I´ll some thing different. Once the rfid token is placed on the reader it will turn on the valve until I place the token again on the reader. In this case I will not send so much data. Could any one help me with this rule or giv...

sawo

When I remove the rules and place the rfid token on the reader, it will reboot after 70 seconds.

sawo

Hi,

attached you´ll find a picture of the device settings.
Nothing to change or setup.

Sawo

sawo

Hi, so last night I had time to learn about the rules and I have managed to create the rules. The value will be set to "0" when token is removed.:-) But now I have the next issue, the rule causes the wemos to reboot after 24 seconds..... and also the load will be by 100% Could any one chec...

sawo

hi grovkillen,

thanks for your reply.
Okay I'll give it a try. Never set up a rule in espeasy before

thanks
sawo

sawo

Hi all, I would like to apologize in advance if this has already been asked several times before. My current project is to control a water hose with a RFID token. Current setup: - Wemos D1 mini (espeasy) - RDM6300 RFID - Relais for magnetic valve - Homematic (Generic HTTP controller) - iobroker (rul...

Search found 36 matches

Re: Cyble Sensor V2 ITRON

Re: Rule doesn´t work...

Re: Rule doesn´t work...

Re: Rule doesn´t work...

Re: Rule doesn´t work...

Re: Rule doesn´t work...

Rule doesn´t work...

Re: Wemos D1 mini - which GPIO ports for relays?

Re: Wemos D1 mini - which GPIO ports for relays?

Re: Wemos D1 mini - which GPIO ports for relays?

Re: Wemos D1 mini - which GPIO ports for relays?

Re: Wemos D1 mini - which GPIO ports for relays?

Re: Wemos D1 mini - which GPIO ports for relays?

Re: Wemos D1 mini - which GPIO ports for relays?

Re: Wemos D1 mini - which GPIO ports for relays?

Re: Wemos D1 mini - which GPIO ports for relays?

Re: Wemos D1 mini - which GPIO ports for relays?

Re: Wemos D1 mini - which GPIO ports for relays?

Wemos D1 mini - which GPIO ports for relays?

Re: Rules for bathroom ventilation

Re: Rules for bathroom ventilation

Rules for bathroom ventilation

Re: Old LCD with ESP ?

Old LCD with ESP ?

Re: RFID update values when removing tag

Re: RFID update values when removing tag

Re: RFID update values when removing tag

Re: RFID update values when removing tag

Re: RFID update values when removing tag

Re: RFID update values when removing tag

Re: RFID update values when removing tag

Re: RFID update values when removing tag

Re: RFID update values when removing tag

Re: RFID update values when removing tag

Re: RFID update values when removing tag

RFID update values when removing tag