Search found 8 matches
- 11 May 2020, 18:46
- Forum: ESP Easy: General Discussion
- Topic: 2 Switch, 1 LED blink and light
- Replies: 11
- Views: 13498
Re: 2 Switch, 1 LED blink and light
Ok so i can note have pulse with only 50 percent pwm signal? Pulse is only 100 percent power for the led if I understand it the right way?
- 11 May 2020, 17:33
- Forum: ESP Easy: General Discussion
- Topic: 2 Switch, 1 LED blink and light
- Replies: 11
- Views: 13498
Re: 2 Switch, 1 LED blink and light
Now it works thc Can i combine pwm and longpulse? I want to habe a differt lightsize between day and night and want to do this this the time. On garage_close#State=0 do //stop blinking timerSet,1,0 // Light off GPIO,13,0 endon On garage_close#State=1 do //blink timerSet,1,1 endon On garage_open#Stat...
- 10 May 2020, 21:50
- Forum: ESP Easy: General Discussion
- Topic: 2 Switch, 1 LED blink and light
- Replies: 11
- Views: 13498
Re: 2 Switch, 1 LED blink and light
One more question is it also posible to send a puls with lower voltage or pwm so that the led only has 50 percent light?
- 10 May 2020, 21:28
- Forum: ESP Easy: General Discussion
- Topic: 2 Switch, 1 LED blink and light
- Replies: 11
- Views: 13498
Re: 2 Switch, 1 LED blink and light
Ok thx thisbis what i found on the wiki
I will updaten it tomorrow. And test it again.
I will updaten it tomorrow. And test it again.
- 10 May 2020, 21:01
- Forum: ESP Easy: General Discussion
- Topic: 2 Switch, 1 LED blink and light
- Replies: 11
- Views: 13498
Re: 2 Switch, 1 LED blink and light
Hallo, I use version 120.
For the level you mean like in the picture.
The switches i also add pictures
I tested the pulse with the url command, bit it says unknown command
http://192.168.0.42/control?cmd=LongPulse_mS,13,1,400
The rules i also add but its not working, i will test it again tomorrow
For the level you mean like in the picture.
The switches i also add pictures
I tested the pulse with the url command, bit it says unknown command
http://192.168.0.42/control?cmd=LongPulse_mS,13,1,400
The rules i also add but its not working, i will test it again tomorrow
- 10 May 2020, 10:08
- Forum: ESP Easy: General Discussion
- Topic: 2 Switch, 1 LED blink and light
- Replies: 11
- Views: 13498
2 Switch, 1 LED blink and light
Hallo, I have two switches on GPIO2 (SW1) and GPIO14(SW2) and I have a LED on GPIO 13. The two switches can never pushed parallel due to the hardware! Now I want to have it like this. If SW1 is pushed and SW2 is not pushed then the LED should be off If SW1 is not pushed an SW2 is not pushed the LED ...
- 10 May 2020, 10:03
- Forum: ESP Easy: General Discussion
- Topic: Level control Led
- Replies: 3
- Views: 6029
Re: Level control Led
Yes I have checked my l7805cv was ded. So I changed it not it works. thx
- 08 May 2020, 20:54
- Forum: ESP Easy: General Discussion
- Topic: Level control Led
- Replies: 3
- Views: 6029
Level control Led
Hallo, I Hava A Switch on the Gipo 2. This works perfekt, and I habe a Led on Gipo 16.therfore I have aded a level control which change if value from switch change to 1. This also works and if i press teh butten the level control on gipo16 also switch between 0 and 1,but the output voltage on gipo 1...