Search found 18 matches

by 2stimpy
19 Oct 2020, 09:25
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

Ok, I wasn't sure about the visible ip.
At first I thought it was ok, you can see it in a quote. Later I thought, better safe than sorry. But of course it had no effect because of the quote witch already had my ip in it. :(
by 2stimpy
18 Oct 2020, 21:42
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

I do not have dhcp enabled because I like to have a fixed ip, so I know on what address I can reach the pi. I did te upgrade and this was my log right after that. Strange thing is that mqtt is connecting right away. 21:24:18 ......... 21:24:18 Event: GenMQTT#Connected 21:24:18 Event: System#Boot 21:...
by 2stimpy
18 Oct 2020, 19:28
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

I did a new fresh install with the desktop and let it update after installation. After that I installed RpiEasy again and configured it. I have no idea why this is happening but again my (ethernet) network does not seem to work correct. 19:23:00 Event: gpio2#HekStatus=0 19:23:00 Event: gpio3#Deurbel...
by 2stimpy
16 Oct 2020, 20:54
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

I have debian buster installed, maybe thats the problem.
I'll try raspbian this weekend.
by 2stimpy
15 Oct 2020, 19:43
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

Even with the relay disconnected this message appears. The power supply is an original pi one. below is a log without anything connected. 19:39:48 Event: gpio2#HekStatus=0 19:39:48 Event: gpio3#Deurbel=0 19:39:48 Event: gpio4#Brievenbus=0 19:39:48 State preserving is disabled 19:39:48 Event: gpio14#...
by 2stimpy
15 Oct 2020, 18:43
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

18:31:35 Event: gpio2#HekStatus=0 18:31:35 Event: gpio3#Deurbel=0 18:31:35 Event: gpio4#Brievenbus=0 18:31:35 State preserving is disabled 18:31:35 Event: gpio14#Doorgang=0 18:31:35 Event: GenMQTT#Disconnected 18:31:35 MQTT controller: xxx.0.0.xxx:xxxx connection failed [Errno 101] Network is unrea...
by 2stimpy
14 Oct 2020, 20:34
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

If I check that box, after I press submit, it automatically unchecks. Probably because I use output(high), I use this, because this is the only setting to make sure the relay does not switch at startup. And that probably has something to do with the fact that when the relay is low, the state is 1. A...
by 2stimpy
13 Oct 2020, 23:11
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

Just one tiny thingy.
If I reboot the system, I first have to use the toggle switch in the webif before the relay starts reacting to the set topic.
by 2stimpy
13 Oct 2020, 23:01
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

Thanks for updating, great work. Now if I push the toggle switch, I get a state message. But if I publish a 1 or 0 to the set topic, the relay switches, state changes in the webif. But I don't get a message at the state topic. I am sorry, I missed the option box "Response to remote commands for...
by 2stimpy
13 Oct 2020, 20:34
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

Okay, so i added this.

Code: Select all

On relais#hek do
 if [relais#hek]=1
   gpio,15,1
   publish,RPIEasy/relais/hek/state,1
 else
   gpio,15,0
   publish,RPIEasy/relais/hek/state,0
 endif
endon
It does report to that state topic, but on one switch moment I get over a thousand messages.
by 2stimpy
12 Oct 2020, 20:25
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

I managed to get it working bij using the set topic as the state topic. I don't think this is the right way but it works. Indeed, it is not a very good solution. Maybe i can add a new option to P029 plugin for non-Domoticz systems to report back. That would be nice, the way i have it now is not wor...
by 2stimpy
11 Oct 2020, 22:01
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

I managed to get it working bij using the set topic as the state topic. I don't think this is the right way but it works. What could be the issue when I use it like this? Now I have to figure out how to automatically switch the relay back of after 1 or 2 seconds. It needs to act as some kind of push...
by 2stimpy
11 Oct 2020, 16:11
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

I am indeed using the domoticz output helper. Should I use a switch instead? https://i.ibb.co/6rxb00t/controller.jpg https://i.ibb.co/h77J0h1/Device.jpg https://i.ibb.co/WpGG3dj/Devices.jpg https://i.ibb.co/94rtXVK/mqtt-lens.jpg https://i.ibb.co/JQYYVQV/mgtt-switch-hass1.jpg https://i.ibb.co/r4rwft6...
by 2stimpy
11 Oct 2020, 12:52
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

I have chosen to go wired now, and with the pi I will be able to add different options in the future. I have it all set up but I can't get it to work like it should. In my home assistant I added the mqtt switches. I am testing mqtt with mqtt lens. If I press the toggle button in the web interface, t...
by 2stimpy
09 Oct 2020, 22:56
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

That must be it, I indeed have a 5v relay. I ordered a 3 volt one right away and will try that. You can use your 5V relay by adding 4 pieces of passive parts between the RPI and the 5V relay: https://m.blog.hu/bi/bitekmindenhol/image/rele.jpg https://m.blog.hu/bi/bitekmindenhol/image/panel1_jpg.jpg...
by 2stimpy
08 Oct 2020, 18:42
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

But now I would like to control a relay which I wired to the gpio15. ... The relay got power from the 1st pin with the 3rd ground pin. The red light is on. I guess you are trying to use an 5V relay with a 3.3V GPIO, which will not work. If VDD=5V than High level needs to be 0.7 x VDD = 3.5V, check ...
by 2stimpy
07 Oct 2020, 19:37
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 312
Views: 105721

Re: RPIEasy

Could someone help me with my rpi setup? I have everything set up and working for 3 switches to be monitored. Configured mqtt to receive messages from the pi on switch change. But now I would like to control a relay which I wired to the gpio15. I setup gpio15 as an output. I added Output - Domoticz ...
by 2stimpy
07 Oct 2020, 19:24
Forum: Introduce yourself
Topic: new guy
Replies: 1
Views: 851

new guy

Hi, I am Arnold and live in the Netherlands.
I have a few nodes running esp easy, and now i am trying rpieasy to get a wired solution.
I am controlling everything with Homeassistant.