Value set to 4: scdgettmp:

Thanks for looking to the code and confirming this behaviour.
I'm not able to correct the code so did you have a solution form me (us)?
Around 4°C difference is very much ... on or two would be ok for terrarium (second one) but 4 is to heavy.

Best regards ...Carsten

A little problem, Ambiente temp is 27°and the SCD30 shows 31° The temp offset is set to -4.00° Is there a bug with the temp offset? Settings: Bildschirm­foto 2022-08-13 um 17.20.20.png scdgettemp outpt: Bildschirm­foto 2022-08-13 um 17.25.39.png I remember the that I saw this before ... actual FW: E...

Thank you for your explanation and work.

Many thanks!

Stupid question ...where to start to find plugin commands? I looked into the plugin list and the wiki or espeasy.readthedocs.io.
Is there an initial starting point for commands?

Hi all,

with the rotary encoder I can set the value up and down, works well.
[RE01#Counter] shows the actual value, but how can I set the value of the rotary encoder from "Tools" section of the eayesp?

Best regards ...Carsten

I'm done, thanks for your help!

Changed to GPIO21 & GPIO22 and ............ WOW!!! :!: :D :D :D :D :D :D :D :D Cold or warm boot ... it works! Many many thanks to all helping guys, it was a rocky road for me, but now it's working! So start the next adventure .... to store some values for temp and hum, a second relay for the ra...

The sensor is connected to SDA: GPIO-4 & SCL: GPIO-5 and +- from ext PS. Will try this tomorrow but if this not working that not not my goal to append the sensor after powering up. ;-) [EDIT] with attaching the sensor after powering up is it now working also with the cheapest PS. :shock: Hope th...

1. test: Nothing works. :-( I tried with 10, 220 and 1000uF or 10k, 20k or 47k ...all the same ... warm reboot and all working. IMG_6041D.JPG 2. test without any R or C and NO I2C Parts only rotary encoder and relay box: It works! 3. Test only with display with rotary encoder and relay box: It works...

Thank you for your patience with me and thanks for sharing this link, seems really to be a crappy board. :-| I'm not really fit in electronics can only "paint as numbers", so please excuse this. With sketch I mean for FET and relays board ... Ok, direct connection 3V3 zu GPIO doesn't work ...

Thanks all for helping. I tried all hints except the MOSFET ....but no no no :-( @chromo23, did you have sketch for this mod? 10uF mod I tried also but also without success (10uf, 220uF and 1000uf). :-( I tested with two other ESP32 Dev C and all the same. After all test is it now again powered via ...

WiFiDisconnect and WiFiConnect

Mmmh, will try it ans before a deep dive in the docs .. I think should be then in the rules?!

I tried it .. 450uF up to 2000uF all the same (on random places). :-( And the other mod like bridging the diode and so on ... nothing (works for me). I like to find the problems but is there another solution as "check WLAN after init of the ESP again and if not restart WLAN"? Than would be...

@chromo23, yes you are right, only +relais box and no more other hardware. USB port is via a USBC to USBA Adapter. No, then it works as expected so I choose an externe PS. @TD-er, please take a look to the picture. No, no external antenna but this is not a closed metal box. Front / Back / Top are pr...

Thanks, I wil do ...
A log ok but how to do with external power supply (USB and ext PS should be not together applied)? My USB PS or USB port (on my Mac) is not powerful enough.
The external PS is Meanwell 5v/5A.

Sorry for the delay but family first ;-) Thanks for the hints, tried but no success with ESO8266 and changed to ESP32 Dev Kit. Now it works with out the relays box on "cold boot" but with not, no WLAN. Only a push to the reset button makes working WLAN again. :-( Should I open a new thread...

Thanks for the links, will take a look.

My wife says that the ESP restarts now randomly, more at the weekend.

Thanks for the hint, if I understand right this rule - ask for Sensor01#Temperature - when the > rotary the power up the relays - when the < rotary the power down the relay - fin I tried it ... but now it is always power up ... no matter what I set on the rotary, clearly at boot the RE = 0. But when...

Thanks for your reply ....

but it doesn't work did you have any other hint (in the display I use it with brackets)?

[EDIT] In the log seems all ok with numbers or [RE01#Counter]

Hi all, my rule doesn't work as expected want to build a temperature controlled fan. The rotary encoder should be set the temperature level for switching on / off the relays board. Hardware setup: esp8266, rotary encoder (RE01), display and a relay board (GPIO16). I can show the rotary "counter...

Thanks for all helping.
In the last week I did the calibration and it works (after new flashing the ESP) without "Restarting the calibration".

Many thanks for the explanation. Some other observation: Offset with "-" number values not working if I use the "+" offset value for the "calibration" (wrong way round) the temp goes slowly down to the right value AND when the "calibrated" value is reached the...

Thanks, that was what I read in the docs. No, only one SCD30 sensor and one non active BME280 sensor (deactivated, the temp offset for the BME280 works). ========= EDIT offset in positive is also not working ========= EDIT 2 strange, now offset from 20 and the temp is falling down (it takes some mor...

Did some one test to adjust the temp offset for the sensor?
My sensor shows to high temperature so the offset should set to -1.50°C but it seems not working.
Is there a trick? Thanks and regards ....Carsten

@Ath,
wow, now it worked for me out of the box, many thanks!

EDIT POST by myself =============== Sorry for the late reply, i am always in Bonn during the week (Berlin - Bonn - Berlin) and at the weekend the family comes first, so i don't have much time to experiment with the ESP32. Thanks for the "factory hint". Today I tried it it again without su...

Hi, thanks for your answer. Yes you're so right and I was to stupid to choose the right plugin and this can't work with my SCD30 ... head bashing (was really to late yesterday). I read the plugin name so often and did not recognises that I'm using the wrong. :-( Choosing the right "bin" an...

Hi all, first, thanks for your work for the SCD30 sensor. But I had a little problem to get the data from the sensor. In easyesp (https://github.com/letscontrolit/ESPEasy/releases last release)I can choose the "Gases - CO2 Senseair", enable it and use the I2C protocol. I tried all I2C addr...