Search found 28 matches
- 02 Jan 2024, 19:57
- Forum: ESP Easy: General Discussion
- Topic: How to find the best WIFI signal
- Replies: 2
- Views: 9911
How to find the best WIFI signal
Hi, I have the problem that the house is covered by multiple accesspoints. Some go away unexpectedly, some come up slowly. The ESP might connect to a distant one, -80 or less RSSI. That basically just allows to connect and does flaky communication, ping works on and off, usually can't connect with a...
- 02 Jan 2024, 19:37
- Forum: ESP Easy: Hardware
- Topic: WT32-ETH01
- Replies: 128
- Views: 178672
Re: WT32-ETH01
Forgot which version I tried, but the board is now bootlooping even with an ESPHome firmware, which works fine with a pristine WT32-ETH01, so beware!
- 29 Oct 2023, 20:47
- Forum: ESP Easy: General Discussion
- Topic: how to inverse MQTT payload
- Replies: 2
- Views: 794
- 29 Oct 2023, 19:07
- Forum: ESP Easy: General Discussion
- Topic: how to inverse MQTT payload
- Replies: 2
- Views: 794
how to inverse MQTT payload
Trying to make a relay work over MQTT. MQTT import works fine, but would be nice to invert the payload of the MQTT message not to go insane. This works just fine: on mqtt#venti1 do logentry,"venti1 %eventvalue%" pcfgpio,8,%eventvalue% endon I hoped "1-value" would work, but appar...
- 29 Oct 2023, 18:57
- Forum: ESP Easy: Hardware
- Topic: battery powered sensor
- Replies: 4
- Views: 1402
Re: battery powered sensor
Yeah, I connected an ESP12F directly to 3xAA NiMH batteries. ESP is happy with the ~4.2V input. I have an SHT20, powered on demand with a FET (power pin is set with hardware/defaults) and a DS18b20 always powered it does not seem to consume much idle. Both devices do NOT publish data to the controll...
- 23 Oct 2023, 09:22
- Forum: ESP Easy: Hardware
- Topic: battery powered sensor
- Replies: 4
- Views: 1402
Re: battery powered sensor
Another interesting question is, taskrun MQTT publish seems to run queued, if I do deepsleep right after taskrun nothing gets published. Does publish also run queued or it waits and the next command is execute only on success? I might do better with disabling report to controller on the device and d...
- 23 Oct 2023, 09:11
- Forum: ESP Easy: Hardware
- Topic: battery powered sensor
- Replies: 4
- Views: 1402
battery powered sensor
Hi, I'm trying to get the best availability time for my battery powered sensor. I'm good with power usage in deepsleep. Will set static IP to reduce traffic and wake time. What else can I do to reduce wake time (and power usage)? Data submission is done with a rule: "On MQTT#Connected Do //when...
- 23 Oct 2023, 08:43
- Forum: ESP Easy: General Discussion
- Topic: MQTT duplicated messages
- Replies: 2
- Views: 1444
MQTT duplicated messages
Hi, I'm getting here MQTT messages duplicated, like: Topic: homeassistant/esp_01_3/bojler/Temperature 22 2023-10-23 08:28:22:807 Topic: homeassistant/esp_01_3/room/Temperature 22.2 2023-10-23 08:28:22:903 Topic: homeassistant/esp_01_3/room/Humidity 52 2023-10-23 08:28:23:006 Topic: homeassistant/esp...
- 08 Oct 2023, 19:50
- Forum: ESP Easy: General Discussion
- Topic: ESP Easy + Home assistant + MQTT auto discovery
- Replies: 10
- Views: 2346
Re: ESP Easy + Home assistant + MQTT auto discovery
No worries, would have been a nice-to-have thing, editing HASS configuration.yaml isn't that bad.
- 08 Oct 2023, 17:29
- Forum: ESP Easy: General Discussion
- Topic: ESP Easy + Home assistant + MQTT auto discovery
- Replies: 10
- Views: 2346
Re: ESP Easy + Home assistant + MQTT auto discovery
Does not really work on the first try... Settings as attached. I get messages on enabling the controller: Topic: homeassistant/esp_08_1 connect 2023-10-08 17:16:53:935 Topic: homeassistant/esp_08_1 connect 2023-10-08 17:16:53:954 Topic: homie/esp_08_1/$state ready 2023-10-08 17:17:14:454 Topic: homi...
- 05 Oct 2023, 16:21
- Forum: ESP Easy: General Discussion
- Topic: ESP Easy + Home assistant + MQTT auto discovery
- Replies: 10
- Views: 2346
Re: ESP Easy + Home assistant + MQTT auto discovery
Updated the esp8266 firmware with ESP_Easy_mega_20231004_collection_A_ESP8266_4M1M.bin. Setup controller as on the screenshot. The only message I got with mqttx is: Topic: homeassistant/esp_08_1 Connected I've set an AHT20 sensor to report with MQTT, that sends messages: Topic: homeassistant/esp_08_...
- 05 Oct 2023, 14:12
- Forum: ESP Easy: General Discussion
- Topic: ESP Easy + Home assistant + MQTT auto discovery
- Replies: 10
- Views: 2346
Re: ESP Easy + Home assistant + MQTT auto discovery
Yeah, looks like login helped with the download. Will test soon.
- 04 Oct 2023, 17:43
- Forum: ESP Easy: General Discussion
- Topic: ESP Easy + Home assistant + MQTT auto discovery
- Replies: 10
- Views: 2346
Re: ESP Easy + Home assistant + MQTT auto discovery
Could test on ESP8266, but meeh how to get the artifacts? Seems to be unclickable at github.... I'm unlikely to build myself
- 04 Oct 2023, 10:31
- Forum: ESP Easy: General Discussion
- Topic: ESP Easy + Home assistant + MQTT auto discovery
- Replies: 10
- Views: 2346
ESP Easy + Home assistant + MQTT auto discovery
Did anyone have success doing auto discovery with Home assistant MQTT with a recent EE?
Can't find much info on the internets.
Have a load of EE units with plenty of sensors, I'd somehow avoid manual configuration.
Can't find much info on the internets.
Have a load of EE units with plenty of sensors, I'd somehow avoid manual configuration.
- 21 Sep 2023, 16:47
- Forum: ESP Easy: Projects / Applications
- Topic: HTTP Advanced to InfluxDB not working, error not visible
- Replies: 17
- Views: 14757
Re: HTTP Advanced to InfluxDB not working, error not visible
ough yes, influxDB is picky on newlines and spacing So the body needs to be exactly like this, no extra spaces, single line: esp,unit=%sysname%,device=%tskname%,sensor=%vname1% value=%val1% %unixtime%%LF%%2%esp,unit=%sysname%,device=%tskname%,sensor=%vname2% value=%val2% %unixtime%%/2%%LF%%3%esp,uni...
- 23 Jul 2023, 19:06
- Forum: ESP Easy: Hardware
- Topic: WT32-ETH01
- Replies: 128
- Views: 178672
Re: WT32-ETH01
Which is the last build I can try?
- 23 Jul 2023, 08:28
- Forum: ESP Easy: Hardware
- Topic: WT32-ETH01
- Replies: 128
- Views: 178672
Re: WT32-ETH01
Nope, it's dead in the water. With some recent miniterm I get: ets Jun 8 2016 00:22:57 rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DOUT, clock div:1 load:0x3fff0018,len:4 load:0x3fff001c,...
- 22 Jul 2023, 14:37
- Forum: ESP Easy: Hardware
- Topic: WT32-ETH01
- Replies: 128
- Views: 178672
Re: WT32-ETH01
Got a brand new v1.4 board, with a WT32-S1 chip. Flashed first with blank_4MB.bin, then mistakenly with a non-factory bin. Flashed again with blank_4MB.bin , then with ESP_Easy_mega_20230623_normal_ESP32_4M316k_ETH.factory.bin serial terminal spits out an endless loop of: ets Jun 8 2016 00:22:57 rst...
- 19 Mar 2023, 13:38
- Forum: ESP Easy: General Discussion
- Topic: Custom UI
- Replies: 3
- Views: 1071
Re: Custom UI
Yes! Thanks
- 19 Mar 2023, 07:25
- Forum: ESP Easy: General Discussion
- Topic: Custom UI
- Replies: 3
- Views: 1071
Custom UI
Hi,
Saw somewhere some custom UI for ESP Easy with tiles and whatnot. Nice buttons per switch on the main page, etc. You need to upload some custom index.html to make it work.
But lost the link and google is somehow not helpful.
Thanks for hints
Saw somewhere some custom UI for ESP Easy with tiles and whatnot. Nice buttons per switch on the main page, etc. You need to upload some custom index.html to make it work.
But lost the link and google is somehow not helpful.
Thanks for hints
- 11 Feb 2023, 20:59
- Forum: ESP Easy: General Discussion
- Topic: ESP just blinking
- Replies: 3
- Views: 1103
ESP just blinking
Using a D1 mini, on power up it sometimes just blinks the blue LED for long, starts a lot later.
Then after a while it goes again into this blinking mode and goes unreachable.
Sounds like some panic mode. How to debug/figure what's wrong?
Then after a while it goes again into this blinking mode and goes unreachable.
Sounds like some panic mode. How to debug/figure what's wrong?
- 24 Jan 2023, 10:38
- Forum: ESP Easy: General Discussion
- Topic: switch not firing events?
- Replies: 1
- Views: 959
switch not firing events?
Have here a seemingly "normally" configured switch (see pic).
State on the devices page is nicely changing value when flipping the switch, but there are no events fired in the log.
What am I doing wrong?
(it is a Build: ESP_Easy_mega_20221224_collection_A_ESP8266_4M1M Dec 24 2022)
State on the devices page is nicely changing value when flipping the switch, but there are no events fired in the log.
What am I doing wrong?
(it is a Build: ESP_Easy_mega_20221224_collection_A_ESP8266_4M1M Dec 24 2022)
- 14 Jan 2023, 08:11
- Forum: ESP Easy: General Discussion
- Topic: How to debug DNS lookups?
- Replies: 3
- Views: 1151
Re: How to debug DNS lookups?
I'm using Build: ESP_Easy_mega_20221224_climate_ESP8266_4M1M Dec 24 2022 Trying to set controller / Generic HTTP address by name, but somehow does not work. IP works fine. Lookup is for a local host, tries from other local (linux) PCs work fine. DNS server is the local router, set by DHCP. Haven't t...
- 13 Jan 2023, 17:43
- Forum: ESP Easy: General Discussion
- Topic: How to debug DNS lookups?
- Replies: 3
- Views: 1151
How to debug DNS lookups?
Something is wrong with my units, they somehow cannot lookup host by DNS.
A 'dig' or 'ping' like command would be nice, but don't find such in the docs.
A 'dig' or 'ping' like command would be nice, but don't find such in the docs.
- 08 Jan 2023, 17:00
- Forum: ESP Easy: General Discussion
- Topic: configuring multiple devices
- Replies: 6
- Views: 1407
Re: configuring multiple devices
Yes, that's how I'd handle common settings across more nodes instead of copypasting rows in the sheet.
But if you better like copypaste, you can still do that.
Next might be a script that executes actions across more nodes.
But if you better like copypaste, you can still do that.
Next might be a script that executes actions across more nodes.
- 06 Jan 2023, 20:49
- Forum: ESP Easy: General Discussion
- Topic: configuring multiple devices
- Replies: 6
- Views: 1407
Re: configuring multiple devices
Updated the sheet a bit with colors and comments. Hope that makes it a bit more clear. Feel free to ask what's not clear.
- 05 Jan 2023, 21:53
- Forum: ESP Easy: General Discussion
- Topic: configuring multiple devices
- Replies: 6
- Views: 1407
- 02 Jan 2023, 16:42
- Forum: ESP Easy: General Discussion
- Topic: configuring multiple devices
- Replies: 6
- Views: 1407
configuring multiple devices
Hi, I'll have a load of ESPs (10+) soon. I'd avoid somehow to have to configure every single one via the browser by clicking around. Is there something out there that can do this for me? Or even better, I'd have a sheet/file/something describing the config of each (mostly similar) ESP config and run...