Let's Control It

Stuntteam

Yeah.. sorry, a bit late for a Santa release..

but too much on my plate atm.
Will be available asap.

Stuntteam

New version will be available soon.
We have added full support for Keeloq protocol includion encryption/decryption.
Keys will be needed but we have a way to obtain keys.

Stuntteam

Thanks for reporting, should be solved in the next release..

Stuntteam

I think the bi-directional models are not supported yet..

Stuntteam

Op de transceiver staat: RTX-MID-868 Dat moet volgens het label inderdaad de 868mhz zijn. De sensoren doen het doen zijn: Sonoff pir2 Alle e-tiger deur/raam sensoren (heb beide generaties). Beide pir sensoren (pet friendly en de gewone) En hun brandalarmen. Zijn dat allemaal 433mhz sensoren? Ik ont...

Stuntteam

>Wat mij tijdens het testen wel op viel, maar niet weet of dit een raar is, is dat al mijn 433MHZ sensoren wel ontvangen worden (het zij met heel slecht bereik (lees 2 meter). Ik heb geen idee wat je precies voor hardware gebruikt, maar... Als je een 868mhz ontvanger hebt dan ontvang je daar geen 43...

Stuntteam

in progress..

Stuntteam

Hi,
data was ok, things are in progress.

Stuntteam

je pense opter our un RBX8 au lieu d'un RBX6... est ce une bonne solution ? Unknown, untested. Perhaps someone else tried it... pour l'émetteur je reste sur un basique FS1000A mais j'ai en stock des H34C et des SY115, que choisir ? Not much difference. je suis tombé sur un Module Émetteur-Récepteur...

Stuntteam

Nee, is er niet.
Ik ben wel bezig met een ESP versie.

Stuntteam

Hmm, strange,..
At least not intentional.
Can you make debug logs?
(see: https://www.rflink.nl/develop.php)

Stuntteam

The PCB shows that it is actualyl an Elero remote control. They use some form of scrambling and a rolling code. I did not find any info revelaing the modulation type. This does need to match the recveiver chip or the receiver must allow setting it on the fly. One thing is sure, it will not work &quo...

Stuntteam

Normally you should not loose settings.
but you might want to write down the data table that is visible with rtsshow

Stuntteam

It's ok

Stuntteam

Yes, always good to have a bit more to verify we can catch all packet types

Stuntteam

So far the logs we have received indicate that there are some different flavors. More work is needed to get them all working.

Stuntteam

Can you provide a debug log as shown here: https://www.rflink.nl/develop.php
But for step 3 activate only the logmode unhandled
That might help in improving things.

Stuntteam

We are still looking into this. One problem seems to be that the RF signal for ON and OFF is the same. At least the logs I got so far are showing only 1 packet for on and off.. It would be good if anyone can confirm this is the case. Anyway, if so then due this this and the fact that RF packets can ...

Stuntteam

It has been fixed and tested.
It will be in the upcoming release (52).

Stuntteam

Thanks,
good news.. propper support for Zaffer will be added to the next release..

Stuntteam

HI,
Please send me log data for all options/buttons so I can check what is going on. (frankzirrone@gmail.com)

Stuntteam

Besides the frequency also the modulation type is important. RFlink currently supports ASK/OOK modulation. If the blinds work with some other type of modulation nothing is received. Give it a try to see if something is received... or.. Open the remote and look inside at the parts, possibly they reve...

Stuntteam

Yes, if you can make a debug log and mail that to me it would be great..!

Stuntteam

RFLink v1.1 R51 (12-01-2024) - New Device: Unitec W186-F Temperature sensor - New Device: Amazon Basics Meat Thermometer - New Device: Valoin Wireless Digital Meat Thermometer With Dual Probe - New Device: Atech-WS308 temperature sensor - New Device: Auriol 4-LD5661, Auriol 4-LD5972, Auriol 4-LD6313...

Stuntteam

Did you check out: https://www.rflink.nl/index.php
it has a step by step introduction to the world of home automation..

Stuntteam

TXT141-BV2 is supported, we are looking at the BV3..

Stuntteam

Thanks, I will take a look at this.

Stuntteam

bbq thermometer, Bresser/baldr and FT007 I see.. Should not be too much of a problem with the optimized code.. lets see.

Stuntteam

The Version text indeed changed:
20;00;Nodo RadioFrequencyLink - RFLink Gateway V1.1 - R50

Version 51 is planned as well.
I will check if I can make a link between your forum username and an email to see what you mailed and if I can implement it asap..

Stuntteam

See email..

Stuntteam

Hi,

I just tested the PCR800 and all seems fine.
Can you make a debug log as described here: https://www.rflink.nl/develop.php
and mail that to me?

Stuntteam

Unsupported devices should show debug data if they use the same frequency and modulation type of the used receiver hardware module. Additionally they need to be within the ranges of accepted pulse length. I have some question marks around the modulation type, it might not use ASK/OOK but rather use ...

Stuntteam

Please provide additional debug data for non supported buttons..

Stuntteam

I have not seen any reports on TFA 30.3180, so it is probably not supported..

Stuntteam

RFLink v1.1 R50 (24-12-2023) - New Device: Abalon Curtain remote (BE301) (receive) - New Device: Lanboo Curtain remote (receive) - New Device: Zaffer Blinds remote (receive) - New Device: Marimex Pool Thermometer - New Device: Gira 225500 - New Device: Deltia 8.33 - Thermostat - X2D - New Device: De...

Stuntteam

It largely depends on the type of Brennenstuhl device. There are the models that follow the ARC protocol which have dip switches or wheels to set the device address. There are also the models that use auto-learn with encrypted communication. Both should be supported by RFLink. However, the packet st...

Stuntteam

You will need an Arduino Mega 2560.

Regarding pricing.. : as low as 6,01 euro's (without a cable)...
https://nl.aliexpress.com/item/32850843888.html

Stuntteam

Do you have any NODO transmitting devices? As NODO is much more DIY and hands-on you would probably already know how to wire. If you dont have NODO devices it does not make sense to wire RFLink for it. You can be sure it will not receive signals from other non-NODO devices. It will for sure not help...

Stuntteam

The short answer: No.

The long answer is that it takes a lot of time and effort to get the signal sorted out. It also would require access to the transmitting device. Right now my limited time goes to improving the current firmware and adding support for devices that are widely used.

Stuntteam

> each of the relevant button presses but they do not control the extractor hood. Did you try to use RFLink with the RFLink loader directly? Thus not using HA to see where the problem lies. Possibly the detection is faulty. In that case debug logs are needed. Look here: https://www.rflink.nl/develop...

Stuntteam

Very old threads.. also many firmware versions ago.
arcadien should show some more data if he wants help..
Like what data he is sending and what data is received.

It might just be that he sends decimal numbers and receives the value in hexadecimal or something like that.

Stuntteam

The pair command is the same as pressing the button at the back of the remote.
It is used for registering and deregistering remotes from the motors memory..

Stuntteam

Following the grouping instructions:
https://www.diyblinds.com.au/guides/how ... mfy-remote
I assume its RC + 1
Not 100% sure though.
Did you setup your original remote and group it as well?
If so, check the debug log (if needed mail me at frankzirrone@gmail.com

Stuntteam

The pairing procedure is the same as with original remotes. You can hook one remote up to multiple blinds.
However, it is more useful to create a different ID for each blind and have the home automation software take care of combining all blinds to one up/down command.

Stuntteam

UP, DOWN, STOP, PAIR are available
ON and OFF can also be used as equivalent of UP and DOWN

Stuntteam

https://www.rflink.nl

Stuntteam

Noty for now.But we might come with a solution..

Stuntteam

A number of pins (4,5,6, and 7) are setup for configuration tasks.. For example: Mega Pin7: connected to ground = no pullup on the RF module signal (default = not connected, pullup enabled) Mega Pin5: connected to ground = GPIO low on startup (default = not connected, GPIO high on startup) Try to co...

Stuntteam

Read here about what to do with unsupported sensors:
https://www.rflink.nl/develop.php

Stuntteam

With the current hardware we do not support FSK modulation.

Search found 777 matches