Unfortunately the display is still off, the problem will most likely be that my circuit uses 2 pcs 74HC959D and the device only has TM1637 and MAX7219.
On my board the pins are labeled: Vcc, SCLK, RCLK, DIO, GND.

Good day, I would need help connecting and operating the ESP8266 and the 7-segment display module with 2 pcs 74HC959D and the temperature sensor DS18b20. I put the temperature sensor into operation, but I am unable to display the temperature on the 7-segment display module.(https://diyables.io/produ...

Build: ESP_Easy_mega_20240329_climate_ESP8266_4M1M Mar 29 2024

Good day,
when setting the font size to Oled 128*64, I need to enlarge the font but the last two items from the menu do not work.
Is there any way to make the font even bigger?

Thank you

Good day,
is there a table of the quality of individual temperature, pressure, humidity sensors from the best to the best?

@TD-er
I think it's OK, I tested it for a while and only 0/1 could change in the Values folder.

Thank you all.

It's a shame that someone didn't think about it and implemented it in ESPmega...

Thank you once again and I have more questions: 1.) I have a temperature sensor Dallas DS18b20 connected to the 1. ESP8266 and sends data to Domoticz and I would like to display the data (temperature). on the small display connected to 2. ESP8266 or ESP32 ? 2.) with Domoticz, I send data to ESP8266 ...

Hello,
so finally I managed to set up a WIFI network with the help of PuTTY and those 3 commands.

Thank you all.

How exactly is it with those buttons, when to hold and when to release?
The left button from USBmicro is "RESET",
right button from USBmicro is "BOOT".

Thank you

My post how I program it is (good - bad): :? 1. On the disconnected ESP32 module, I connect GND and GPIO0 2. I will connect the PC - ESP32 3. I open the page "https://td-er.nl/ESPEasy/latest/" and select the file for example "20240311 Normal 4M LittleFS ETH [ESP32]" 4. Press &quo...

I tried uploading:
1. 20240311 Climate 4M [ESP8266,ESP32,ESP32-S2/S3/C3]
2. 20240311 Normal 4M LittleFS ETH [ESP32]

both have the same "KO" result!

Did LittleFS / SPIFFS split?

Which page do you mean?

Is it not possible to enter the network name and password via AT commands?

This is the dump from the ESP32 after pressing the EN button. Serial port COM6 opened ets Jun 8 2016 00:22:57 rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0030...

This is the rs232 dump after disconnecting GND and GPIO0.

I don't understand why I can't upload "ESPmega", when I use the online programmer, it uploads both TASMOTU and ESPhome (https://web.esphome.io/)....

Hello,
after "uploading" the software, I canceled the connection between GND and GPO0.

I had to connect GPIO0 to GND, otherwise I didn't want to connect to the programmer, the software was uploaded and a message appeared saying that it was OK.
Unfortunately, I don't see any new network in the WiFi manager!
It's like it won't run on the ESP32 AP function.

Thanks, I'm going to test it

Unfortunately, I can't get to the mentioned www page...

Good day, the mentioned site for online uploading doesn't work "https://td-er.nl/ESPEasy/", the only thing I managed to upload to esp32 via online www is tasmota. I couldn't upload Sw Tasmota offline with any program! According to which should I choose which of these: ESPEasy_mega_20240229...

Good day,
unfortunately, it is not possible to control using IR, there is a controller with a display built into the heat pump unit.

Good day,
I would like to control my heat pump "Panasonic WH-SXF12D9E8 Heat Pump" with the help of esp easy, but I am new to this. Can someone help?