Let's Control It

Stuntteam

We are looking into it..

Stuntteam

The ping/pong part is used by controlling software (domoticz/HA) to check if the RFLink is still alive.
It does not say anything about the RF module itself.

Stuntteam

It for sure needs cr/lf on commands..

Stuntteam

Check these:

https://www.npmjs.com/package/homebridge-rflink
https://npm.io/package/homebridge-rflink
https://github.com/mlaurijsse/homebridge-rflink-gateway
https://github.com/Kostya-Green/123
https://snyk.io/advisor/npm-package/hom ... nk-gateway

Stuntteam

Thats an expensive piece of hardware. For such prices I would have moved to some zigbee or wifi switches that offer 2 way communications.. Anyway, I dont know these sets yet. The frequency indeed seems to be 433.92 and the modulation type would be OOK. Both are supposed to work with the RFLink setup...

Stuntteam

in progress..

Stuntteam

Kaku moet gewoon werken.
Ik ga even wat beter kijken naar je debug data.. Heb je toevallig ook debug data van de Forest?

Stuntteam

It might (or not) be helpful to know that the serial number of the shutter's motor is 7062541009013. If I remember correctly, when the remote was initially coupled to the shutter, the serial number of the shutter was coded into the remote. Correct, I identified the serial number, button crontrol an...

Stuntteam

Hi, Zaffer might have some projects that are based on Zigbee. However.. the packets listed in the previous posts are NOT Zigbee. They are indeed regular ASK packets. I have sorted out all the data inside the packets and identified most of the bits within the packets. However, I do not have enough in...

Stuntteam

It is a Phenix (not a real AB400), Is it the YC-4000 model (using HX2262 chipset) ?
Alternatively you could try the rffind option.. (https://www.rflink.nl/faq.php#RFFind)

Stuntteam

I have no idea what the dipswitches are reflecting.
I have tested with commands like:
10;AB400D;00004d;1;OFF;
10;AB400D;00004d;1;ON;

Where 4D is the hexadecimal value of a ascii character which is supposedly set with your dip switches
So I guess:
10;AB400D;000042;2;ON;
10;AB400D;000042;2;OFF;

Stuntteam

Handmatig:
10;Kaku;000041;1;ON;
10;Kaku;000041;1;OFF;
Waarbij de 41 de hexadecimale waarde is van 'A' (42=B, 43=C..)

Stuntteam

No, thats normal..

Stuntteam

The RFlink firmware controls the leds.
What do you mean with "controlling" or what are you trying to do?

Stuntteam

Hi, >2023-01-03 00:55:43.120 DEBUG (MainThread) [rflink.protocol] connected >2023-01-03 01:04:53.020 DEBUG (MainThread) [rflink.protocol] received data: 20;AF;Drayton; This indicates that RFlink is up and functional. It also indicates that data is received and communicated correctly to HA (thus no b...

Stuntteam

Nothing really wrong at RFlink's side but more a side effect from the ASK modulation and the way the transmitters work. RFlink is listening to radio signals. It will receive whatever comes by.. however, there can only be 1 signal at a single moment in time. The more devices you have that are transmi...

Stuntteam

Can you provide a debug log so I can check the issues?
see: https://www.rflink.nl/develop.php

Stuntteam

I would need to see debug data to fix the code.
see https://www.rflink.nl/develop.php

Stuntteam

Hi,

As far as I know, RFlink does not work with Jung devices at 868 mhz.
Btw, it is not just the frequency that plays a part, it is also the modulation type that is important and if rolling codes/encryption is used.

Stuntteam

Hi, Yes.. I would need to look at debug logs to see what is going on.

Stuntteam

Indeed 2 or 3 should be ok..
But also it needs to include a number of consecutive key presses of one single remote to check out the variation in packets and if there is a rolling code or something more simple in the packets.

Stuntteam

It is nice to have the signal strength.
However, it would need to be accessible on one of the RF pins to go forward.
If the pin does provide the signal and we can get hold of the value by adding a capacitor or other extra hardware then it would indeed be a nice addition.

Stuntteam

The zaffer signal as shown in post nr 1 originates from a regular RF signal, meaning it is not zigbee. The signal is clean but does contain something that looks like a counter or rolling code. It would require more packets, also from the other buttons, to determine what is possible in terms of integ...

Stuntteam

It's noted but due to vacations it will take a while..

Stuntteam

That seems to be related to the Home Assistant implementation..

Stuntteam

Perfect!

Stuntteam

Ok, en de Meteolis heeft maar ondersteuning voor 1 remote? Hoe zit dat dan met die kanalen precies? Een Telis4 heeft op, neer en de My knop. Daarnaast is er de kanaal keuze knop voor 4 + 1 kanalen (waarbij die +1 alle kanalen tegelijk is) Hoe doe je dan kanaal 6,7 en 8? Wat GPIO betreft: de Arduino ...

Stuntteam

Het concept met ontvangen en doorsturen (rflink als relay) gaat niet echt werken. Maar als ik het goed begrijp is de Meteolis een basisstation. De meteolis is die dan niet per RTS signaal draadloos aan iedere motor gekoppeld? en de Telis4 is via RTS signaal draadloos aan de meteolis gekoppeld? Druk ...

Stuntteam

Debug mode activeren.. dan moet je data voorbij zien komen.. zie: https://www.rflink.nl/develop.php

Stuntteam

Isnt the panel the base system that mostly receives signals?
It might only be able to send a signal to a siren/alarm light device
Check the debug mode to see if there are missed signals.

Stuntteam

It is all explained here: https://www.rflink.nl/develop.php

Stuntteam

The debug data posted above is not correct.
You are missing a large part of the actual debug data.
Also, when you see Pulses=460 the data behind it should contain at least 460 values and 460 comma's

Also note that when a rolling code is involved, it complicates things a lot.

Stuntteam

If it is, then RFLink must see show some debug data..

Stuntteam

Hi, In general Chacon Dio is supported. It is always possible that a new model is not supported or that there is something else (for example a low battery) that cuases an issue. Make a debug log as described here: https://www.rflink.nl/develop.php and mail it to me (email address is on the page as w...

Stuntteam

Can you say something about the difference between NRF24L01 and NRF24L01+. Indeed it is due to the increased transmission power I assume that after switching on "MySensor:ON" in RFLink Loader the software of the RFLink tries to connect to the NRF24L01+ module. If this does not succeed, my...

Stuntteam

Hi, >I can see in the log that I have turned it on. But the next line is "20;02;MySensors=OFF;NO NRF24L01;" The RFlink firmware will check if the NRF is connected and accessible. If it is not, it will report the OFF state. For Mysensors you need to connect the NRF in the same way as for Mi...

Stuntteam

It would however not work with keeloq...

Stuntteam

Ok, the ID is 6 digits.

Stuntteam

yterza wrote: ↑02 Jan 2022, 22:11 The RTS Pair command only save ID with 6 digits, so I use that one for mine : 2C0B2F (genuine remote id was : 2C0B2F8)

Where did you get the genuine id from / why do you think it is 7 digits?

Stuntteam

Various x2d devices are supported.
I am working on updating both the rflink.nl website and a new firmware release and will try to add more details on the various x2d models.
Note that for the models that are not supported yet I need debug data.

Stuntteam

Details here: http://www.rflink.nl/blog2/development

Stuntteam

That will not work...

Stuntteam

What is the model number/type of your x2d (transmitting) device?
I can check if I have received data for it in the past..

Stuntteam

Obviously the fact that a protocol is supported does not mean each and every device using that protocol is supported. You first need to receive data. If that is not happening you need to check if the receiver hardware is the issue. If nothing is received the hardware needs to be checked. If other de...

Stuntteam

Should work better now..

Stuntteam

Ja, check de batterijen van je devices...

Stuntteam

What kind of device is the transmitter/button ?

Stuntteam

The project is not dead.
We are supporting people with their questions and new unsupported devices.
There are new test versions supplied to testers.

Stuntteam

You can see pulses on a scope, but if these pulses do not provide a clean signal then it could just be noise and will not result in any debug data.
Also, do no use the unhandled mode, just use the debug mode.

What kind of RF module do you have?

Stuntteam

Updated the website. The BFT rolling code models are not supported.

Search found 773 matches