Let's Control It

M*I*B

Nope / nope Nope 1: U84 (S20 - Garage) connected to a repeater 1750E in the garage itself. The repeater is wired connected to the FritzBox (via NetGear GS748Tv3) U86 and U121 on my desk are connected directly to my FritzBox Nope 2: Yes, I'm sure that no one is connected to the guest- network. If so,...

M*I*B

The shown port on the Controller tab for the p2p controller is wrong. Yes, have seen that but also don't care of it as you suggested ... But to be honest, I have no clue why other nodes cannot see your "garage" node. Nope, that's wrong. U84 (S20 - Garage) can see itself and can see both o...

M*I*B

TD-er wrote: ↑29 Dec 2022, 13:35 That shouldn't make a difference as the p2p code has not changed in a while... At least not in the past weeks

...I just didn't want to leave it unmentioned as it's the only difference I see...

M*I*B

You don't need to have the p2p controller enabled (or configured) to see the other nodes in the list on the root page. Yes, I know, but due both don't work here it's a try to check out different variations. But as I say: nothing change :? Only having an unique host nr (config tab) and using the sam...

M*I*B

... yep, I do so ... I have open three command prompts so that I can ping all three continuously. I also have delete all controller on all three and set P2P on the 1st place (2nd is now FHEM) I also have delete the virtual device on Task 6 on U121 (as I say before) and also the real device on Task 6...

M*I*B

Hmm ok... We can make a solved behind the INT- thingy... got it now 8-) I can ping all three systems without hassle. The AP in the garage is a AVM1750E (got 3 of them as MESH). I also have reboot all but nothing change. Let me try to change the UDP-port. Since years I have it at 333 but meanwhile yo...

M*I*B

... ohh, thank you very much! So if I like to use the value I have stored into 1 with "Let,1,<value>" I can call it back as int with "if [int#1] blabla" but not with %i1% instead of %v1% ... ?! OT: At the moment I have three devices running the current build: two S20 and one 12S....

M*I*B

Good morning all, maybe a stupid Q but I don't find the right hint in the RTD :roll: Maybe also a problem what to search for. An native EN- speaker use most other words for searching then i.e. a native DE- speaker How can I make an integer result from a formula? Let say I do "Let,1,%eventvalue1...

M*I*B

The ESP12S was only in 4M format.... at least as far as I know. And the ESP07S was also 4M, right? I think so. My main side for that is https://www.esp8266.com/wiki/doku.php?id=esp8266-module-family http://stefanfrings.de/esp8266/ isn't bad also but have never fix the wrong flash size for the 07S I...

M*I*B

... jepp... But do you know that also 12S as 4M version exist? All I have seen the last days are 1M. I can't remember wehere and when I bought that :roll: Now I have write it down on all I have here... quite easy to solder/use if you use the bare modules. That's it. I have to solder small wires that...

M*I*B

UHHHH! That's crasy!!!

: Bild_2022-12-28_202755725.png (149.45 KiB) Viewed 4833 times

That's one of my 12S !!! They have 4M instead of 1M !

I did not know that! So problem solved by ignorance

M*I*B

and you can include a SysInfo task with VCC included, and use [SysInfo#VCC] for displaying. Bild_2022-12-28_191846064.png ... time to stop for today... I can't see the forest for the trees anymore :shock: What are the requirements for that device? - External WiFi antenna - External WiFi antenna AND...

M*I*B

There is no %vcc% variable, in the Formula field you should use %value% to calculate with the current, er..., value. That I don't mean. I mean the sysvar %vcc% you i.e. can use to show on a LCD ... because of size restrictions (despite that being a Normal build), sorry if that caused confusion... N...

M*I*B

You need to connect the device (but there is no check if it is actually connected...), and configure it on the Hardware page, before you will see the relevant options on the Device Configuration page for any I2C device. ... hu? If you say there is no check if present and I configure I²C on the HW- ...

M*I*B

... an other old project just popup out of one of my drawer ... For that I need a I²C Multiplexer like a TCA9548a. Right now I haven't a TCA9548a by hand but I read some about at https://espeasy.readthedocs.io/en/latest/Hardware/Hardware.html It is usually available in the normal, testing and custom...

M*I*B

... I have bookmark that long time ago as you sugested ... But I'm not saying that for fun, that there are both variants on the net and even in some data sheets. But ok. I will check all the different variations by myself. This seems like a better way to me than relying on conflicting statements fro...

M*I*B

Hello there, I'm just create a layout for my (old) new project. While doing that I have take a look who to switch the module into Flash- mode. And... how could it be otherwise... there are conflicting indications :roll: 1. Version GPIO-0 and -15 to GND, CH_PD to VCC 2. Version GPIO-0 and -15 to GND,...

M*I*B

experience taught me that sometimes bugs are healed by time passing by...

... yep, sometimes things happen that make you wonder what's going on... especially these days

M*I*B

i guess it was inference with the bosh microwave :D ... don't ask me that :lol: I have no idea. Can also be my amateur radios or my copter or just the little green christmas elves ... I have no idea :roll: The only thing I know is that our new superdupercombi oven was worth the money. Extremely del...

M*I*B

... LOL ... Then call me BUG-DIGGER right now :lol: :lol: :lol: I just think a bit about... The formular- field is more for other stuff in my eyes and not the place to calibrate the ADC. Is'tn it possible to to create a command like "CalADC,<adc>,<factor>" that you just can enter by hand a...

M*I*B

... unfortunately not. This changes the value sent to the activated controller, but not the value in the device itself ... I have check that out yesterday ...

M*I*B

... yes, that is what I'm looking for... But where can I do that???

Ok, you mean the extra Device "Analog input - internal ", aren't you?
If so we are talking about different things. Picture shows more then 1000 words...

: Bild_2022-12-27_103653313.png (18.32 KiB) Viewed 1333 times

M*I*B

Some OT before bedtime: 1. Sysinfo VCC shows 3.469V but real they are 3,286V (Aneng A3008, Metex M-4650, McVoice M-980T --> +/- 3mV). So it shows round about 180mV too much of. This is with all ESP's I just check (two S20, two ESP-07, one ESP-07S, one D1miniPRO) Is there a way to calibrate that at t...

M*I*B

Sodele... the rolled roast is in the oven (I'm currently testing our new Bosch tripple gastro convection/grill/microwave). Let's see if at least that works :roll: I exumed the timer again. I couldn't think of another solution in connection with the kick-off through the WLAN. // Initialize Tick-Tack ...

M*I*B

Bild_2022-12-26_143548768.png Ok, an other way that I understand it next year also: // Create own Events to check Key and LC at once on Regler#SET do asyncevent,KeyCheck=%eventvalue1% LET,1,%eventvalue1% endon on Taste#BTN do asyncevent,KeyCheck=%eventvalue1% LET,2,%eventvalue1% endon // Ask Keypre...

M*I*B

... yes, you are absolutely right! While you writing this exactly that is flashing up in my brain :D I have placed that at the 1st asking and then it goes as expected :lol: But... The flasher starts as expected but if the WLAN send a pulse to the same GPIO the flasher just stops ... So you may want ...

M*I*B

ok, I have hang a 0 after... But this loop I never touch... I hung ... If I press the button longer then 1s I got the 11 as event but the asking about at ... ... elseif [Regler#settings.enabled] = 1 and %eventvalue1% > 9 // Regler ON and Longpress? gpio,12,0 TaskDisable,4 longpulse_ms,13,1,200,200,-...

M*I*B

Yepp... takes a while to dive into ... SO... I have change the Rule like this: // Create own Events to check Key and LC at once on Regler#SET do asyncevent,KeyCheck=%eventvalue1% endon on Taste#BTN do asyncevent,KeyCheck=%eventvalue1% endon // Ask Keypress and LC on KeyCheck do if [Regler#settings.e...

M*I*B

Ok, get it... Open my knot in brain slooooowwwwlllyyy

M*I*B

Depends on whether you need to invert the LED, of course Hmmm... The LED is the same who show the WLAN- status. The other one is unusable due they are hardwired in parallel to the Relay and not independent usable... So I think I have some misunderstanding about that... LongPulse_mS,<GPIO>,<state>,<...

M*I*B

GREAT - GREAT - GREAT ...
I have overseen the "continous" -1 thingy... Many ty for the Hint!

So I set i.e. ...

Code: Select all

longpulse_ms,13,1,200,200,-1

... for flashing and ...

Code: Select all

longpulse_ms,13,0

... to switch that off?

M*I*B

hmmm ... Ok ... My rule don't work anymore ... crasy ... Funny thing... Flashed again with "20221224_normal_ESP8266_1M_VCC" and now it works :? :shock: EDIT: Now it runs like a charm but creates more load as expected. The way I use the timer only for the situation the "Regulator - Le...

M*I*B

öhhh ...

Can it be that the {task}#settings.enabled thingy isn't implemented into the XMas release mega-20221224 ?

M*I*B

: Clipboarder.2022.12.26-002.png (154.99 KiB) Viewed 2881 times

M*I*B

:D That's good to know! I just counted how many of these I still have in the box. With the test ESP it is then 12 8-) Old project is to use one of them to catch the push-data out of two EasyMeter. There is an IR LED in position 2, which regularly sends the consumption data with 9600bd every 2 second...

M*I*B

... no, I haven't. At the moment I do it nearby while with the family...

: Bild_2022-12-25_201958750.png (32.89 KiB) Viewed 5021 times

M*I*B

MÖÖÖÖKKK

I have flash the "ESP_Easy_mega_20221223_normal_ESP8266_1M_VCC" into the ESP-07 without problems. Seems to be a 1MB version

: Bild_2022-12-25_191052706.png (28.62 KiB) Viewed 5025 times

M*I*B

: Clipboarder.2022.12.25-002.png (78.71 KiB) Viewed 2949 times

M*I*B

Ath wrote: ↑25 Dec 2022, 16:51 Have you tried the "taskrun,regler" command?

Nope... Not really know what you mean

M*I*B

... merry Christmas again... Ok, I think I found a bug or more like an omission in the "Regulator - Level Control". If I change the value at "Set Level" or "Hysteresis", neither is sent to the selected controller, even if I change the value from external (FHEM). As a re...

M*I*B

... ok, I will open one to take a look ...

M*I*B

*Thumbs Up*

: Bild_2022-12-24_190015719.png (232.5 KiB) Viewed 5078 times

Merry Christmas to all of you. Time to spent time with my family. Who knows how often we can do that together ...

M*I*B

... are you sure?
I just now search the net for "ESP-07" and all I have found talk about 1Mb

M*I*B

Hello all, ... I would like to tackle an old project again soon; I had totally forgotten. For this I would like to use one of the ESP xy lying around here. I still have a whole handful each of the D1-Mini-PRO, ESP-07S and ESP-12E. However, I only know the 12E with a circuit board antenna... Does any...

M*I*B

... ... that's just a lame excuse because you want another beer :lol: :lol: :lol: Remember and DON'T FORGET to solder a wire between the E-contact and GND. Then all is save in any way. You can just use a plain wire or better a 47R (10R to 100R is also ok) parallel with 100n between the Earth and GND...

M*I*B

... always the same shit with Christmas! Always comes all of a sudden and without notice...

M*I*B

... I'm glad that my amateur handicrafts have something good for you too :D :geek: I just ordered some other connectors. The 3.5mm stereo (3pin) are also available als 4pin version (former used as Headset/Microphon/PTT) . I have also take a look for the 2.5mm version but this one are'n available at ...

M*I*B

Ok ... I just wanted to let you know of my success ... Bild_2022-12-23_141821987.png Simple work... If you LongPress (1s) you can enable or disable the "Regulator - Level Control". If you disable it, the GPIO for the Relays will be set OFF and also the LED (who show you the WiFi in normal ...

M*I*B

chromo23 wrote: ↑23 Dec 2022, 13:17 Bildschirmfoto 2022-12-23 um 13.15.34.png

Right there ?

: Bild_2022-12-23_132257379.png (74.4 KiB) Viewed 3105 times

There is nothing I can download ...

EDIT: Ok, I have to have a account at GitHub... Now I can...

M*I*B

... jepp, but I'm not able to compile it by myself with my knowledge ...
I have no idea what I have to do with that stuff your provided link show me ...

Search found 379 matches