Let's Control It

Stuntteam

well.. I think it was not the idea of putting support for every protocol on it.. otherwise you simply use RFLink which supports more protocols than any other solution..

Stuntteam

Well, RFLink has no issues recognizing this. The main problem is that Domoticz has no use for the additional commands. We also have no idea what the expected behaviour would be. "Mood" scenarios can be done with scripts within Domoticz anyway. So perhaps these mood buttons should just be r...

Stuntteam

Someone is working on it:
https://github.com/matt2005/pyrflink

Stuntteam

Well.. that is an ASK/OOK module..
We are working on CC1100 and CC2500 support.. through SPI.. for 433, 868 and 2.4 ghz traffic.
There is always a way..

Stuntteam

For various reasons.. like.. because we wanted to keep an option on the use of interrupts and because we could.. and because we might use the digital ports for some things.. and some other reasons.. But why does that matter? It is not like we are short on ports. What other device with a serial inter...

Stuntteam

The firmware does indeed support 868mhz and some devices can be received when you use for example an Aurel 868mhz receiver/transceiver.
There is a pin compatible version of the aurel rtx mid working on 868 mhz.

Stuntteam

Ok, well.. the wiring page shows the pinout and wiring to the Mega for many different modules... Like: Aurel RTX MID 5v: If you would like to use the Aurel RTX MID 5v Transceiver the pinout is: Pin 1 = Antenna Pin 2 = Ground Pin 3 = Not Connected Pin 4 = MEGA tx3/Pin 14 (TX Data) Pin 5 = MEGA rx3/Pi...

Stuntteam

Did you check out http://www.nemcon.nl/blog2 ?

There is a wiring page for various modules:
http://www.nemcon.nl/blog2/wiring

Stuntteam

There are still some pins free.. that we could use if we need to..

Stuntteam

http://www.nemcon.nl/blog2/devlist
scroll down to the 868 mhz section.
Support for additional devices is under preparation.

Stuntteam

Should be possible.. We will make a test version and contact you.

Stuntteam

Hi,

There is no need to grab the exact packet yourself.
Make a debug log for a couple of minutes and make sure the PIR has detected movement during that time.
Send the log by mail to frankzirrone@gmail.com
So that we can check it..

Stuntteam

Release 43 is available! - New Device: MiLight WW/CW remote & Bulbs - New Device: WH3 temperature sensors - New Device: Alecto 1300 Wireless Plant Monitor - New Device: Unitec W235 Climate sensor - New Device: Jula / Marquant 943134 temperature sensor - New Device: Inovalley SM200 - New Device: ...

Stuntteam

see email..

Stuntteam

Great.. we are looking into it..

Stuntteam

Hi..
You should only have RFlink hardware once in your list and for sure not on the same port as the zwave adapter..
also, if you do not get the create device button, the Domoticz version is too old or you need to make sure that the cache of your browser is clean.

Stuntteam

Receive: RFlink kan het RF signaal ontvangen en decoderen Send: RFLink kan het RF signaal coderen en verzenden In dit geval kan je met RFlink dus het signaal dat er rook/brand is ontvangen en je kan het alarm signaal op de fa21 aan zetten.. Als sirene zijn ze overigens niet van die geweldige apparat...

Stuntteam

We might add support for wemos or so in the future.. right now priority lies with getting some other things working properly.

Stuntteam

Target is this week..
update 16/9: slightly delayed.. nearly done..

Stuntteam

Check your mail..

Stuntteam

I have send you an email..

Stuntteam

R43 is not released. If you are using a test version then that might not address anything you are looking for, it might not even be a test version that can be used with jeedom/domoticz etc. but only to test some functionality..

Anyway, does your Smarthome remote have any dip switches?

Stuntteam

Great to hear!!

Stuntteam

No, unless the Nice protocol gets hacked..

Stuntteam

Als je bedoeld bij de garagedeur, dan ja.. dat is in de meeste gevallen wel aan te passen. |Lukt dat niet dan kan je er eventueel ook een ander device zoals een KAKU tussen zetten. Echter.. waarom zou je dat doen??? Beter van niet..! Garagedeuren hebben niet voor niets een "rolling code" s...

Stuntteam

Your system is using the Nice Era protocol.
This is a rolling code protocol which is currently not supported.

Stuntteam

No, bad idea.. keep it original..

Stuntteam

Het blijft een stuk duidelijker als je niet meerdere zaken door elkaar in 1 thread zet. Deurbel: heb je geprobeerd om de bel dichterbij te zetten? Garage: lijkt op FSK modulatie.. daarnaast kan je het vergeten om de deur te bedienen met een andere remote als het signaal een rolling code bevat (met g...

Stuntteam

Generating rolling codes is not needed to receive alarm system sensors.

Stuntteam

Kan je de knop van je afstandsbediening een paar keer loggen zoals in je eerste bericht.
Het gaat dan vooral om het meerdere malen ontvangen van hetzelfde debug pakketje.
Het lijkt er nl op dat het geen ASK signaal is en dan kom je er met je link ook niet uit.

Stuntteam

KAKU / Chacon report open and close signals.
Thats even listed in the device list..

Stuntteam

RFlink will have a modification to properly recognize the Digoo..

Stuntteam

Wat voor remote control gebruik je? Het signaal lijkt niet echt stabiel.

Stuntteam

Zo maar data rondsturen heeft op zich niet zo heel veel zin. Vandaar dat rflink met plugins werkt en iedere plugin een protocol voor zijn rekening neemt. De plugin zorgt voor ontvangst en verzenden met dezelfde timing enz. Om te beginnen helpt het als je aangeeft welke merk en model je afstandsbedie...

Stuntteam

Er is op het moment geen support voor GPIO.
E.e.a. is wel mogelijk maar hangt sterk af van wat je precies wilt doen en of dat goed samen wil werken met de basis functies van rflink..

Stuntteam

Unfortunately these remotes are not of good quality and apparantly often (badly) cloned in Asia...

Stuntteam

Hard to tell without seeing the debug log..
can you mail it to frankzirrone@gmail.com or post it here

Stuntteam

Ok, clear.. so it would be nice if someone else has such a bell and makes a log..

Stuntteam

"The TX is paired with the RX, so I don't know how helpful the debug output will be"

What does that mean?
This is not data that is received in a normal way?

Stuntteam

Yes, for any device that is not or not correctly supported we need a debug log so we can modify the code to get it properly supported..

Stuntteam

Make a debug log as explained here: http://www.nemcon.nl/blog2/development
and mail it to frankzirrone@gmail.com

Stuntteam

http://domoticz.com/download.html Stable Arm 32bit (Raspberry/Cubie/...) 3.4834 2016-03-02 12,35 MB Windows 3.4834 2016-03-02 13,12 MB Mac/OSX 3.4834 2016-03-02 11,69 MB Linux 3.4834 2016-03-02 12,49 MB Beta Arm 32bit (Raspberry/Cubie/...) 3.5541 2016-08-24 12,62 MB Arm 64bit (Cubie/ODroid/...) 3.55...

Stuntteam

Dan is je Domoticz versie te oud.. pak een recente beta versie..

Stuntteam

Thanks.. we will check it out!

Stuntteam

If you follow your own link and check the reviews..
you will see:
Sensor for DomoticzBy:Westcott 2016-06-14 06:53:15
Worked out of the box with RFlink straight into Domoticz as "Temp + Humidity" WTGR800

thus yes, it works!

You can use a maximum of 3 sensors

Stuntteam

Should not be hard.. but so far noone asked for it or implemented the vera side of it..

Stuntteam

Volgens mij heb je die niet goed aangemaakt..

Volg wat hier staat:
http://www.nemcon.nl/blog2/faq
onder kopje:
Q: how to pair Milight bulbs without the original Milight remote control in Domoticz?

Stuntteam

Er worden verschillende rolluik systemen ondersteund. Zie http://www.nemcon.nl/blog2/devlist Op dit moment zijn dat: Window blinds/shutters/sun screens: Kaku ASUN650 Intertechno CMR-500, ITL-500, ITL-1000 Bofu motor controller (Rollertrol?) Brel motor controller (DC90, DC306, DC115, DC229, DC230 and...

Stuntteam

Nee, is niet nodig.

Stuntteam

Yes, please send a debug log.. we are currently implementing some changes to the detection of Eurodomest/EV so we can look at this one as well..

Search found 773 matches