Let's Control It

BertB

Bonjour. parlez vous anglais?

BertB

Which sensor do you have?
Can you measure between t- wire and ground? Is there a connection?
Is the thermocouple not connectoed to other stuff?
I guess you have to do some more research.

BertB

BertB

No that is not the problem since you can upload and run the firmware.
I think in 120, SPI is not supported. You could try to use the release candidate 147-RC8

BertB

What firmware version do you use?

BertB

Sorry, I can't help you. I don't have that MAX.
However, did you check the enable SPI in the hardware tab?

BertB

I did as you suggested.
This is the result.

: Atom4.png (32.59 KiB) Viewed 50709 times

BertB

By the way,

I do not get your list after hitting F7, but this:

: Atom3.png (166.39 KiB) Viewed 50743 times

BertB

After that, I copied al the downloaded library files to the lib folder. After hitting F7 again, I got: [03/07/17 14:50:16] Processing d1_mini (platform: espressif8266, board: d1_mini, framework: arduino) Verbose mode can be enabled via `-v, --verbose` option Converting ESPEasy.ino Collected 44 compa...

BertB

Hi. Thanks for the reponse. I am desperately trying to get things up and running, cause I have a lot of ideas, however this kind of programming techniques, I am not familiar with. So please forgive me for asking many stupid questions. Before I first managed to get any reponse to the F7 keystroke, I ...

BertB

did you also remove all user directories after uninstall, so that you really start on a fresh base. http://docs.platformio.org/en/latest/ide/atom.html#uninstall-atom-with-platformio-ide <-- uninstall instructions... if this does not help, sorry i am also new to platformio :) I am a step further, I ...

BertB

did you also remove all user directories after uninstall, so that you really start on a fresh base. http://docs.platformio.org/en/latest/ide/atom.html#uninstall-atom-with-platformio-ide <-- uninstall instructions... if this does not help, sorry i am also new to platformio :) I am a step further, I ...

BertB

did you also remove all user directories after uninstall, so that you really start on a fresh base. http://docs.platformio.org/en/latest/ide/atom.html#uninstall-atom-with-platformio-ide <-- uninstall instructions... if this does not help, sorry i am also new to platformio :) Yas, I did. You have no...

BertB

@krikk
Okay .. so I removed github and atom completley from my pc and walked through the setup procedures again.
With Linter disabled and Clang (is that safe?) for a later remind.

Still the same problem. When I press F7, i get a pop-up saying that the editor is not reponding ...

: Atom.png (255.66 KiB) Viewed 49125 times

BertB

@psy0rz Great tutorial, works out fine, until you write about Smart Code Linter. Perhaps I installed it without knowing what I was doing. May be this has nothing to do with my current problem, which is that nothing happens (well, Atom seizes to respond) after: Building the correct version Press F7 a...

BertB

Thanks a lot. Can't wait to learn more.

BertB

Hi all, Edwin, thanks for stepping in. I am also available for testing and revieuwing the wiki. Furthermore I would like to continue to enhance my programming skills by making prototypes of plugins. Is that still possible in the new setup? Some other question. How do the relases in ESPEasy-platformi...

BertB

Nice!
And may be broken, but still going strong.

BertB

@Tiit12
You are so right. I measured the signal with my oscilloscope and it never came above 3.3 volt.
So, I got rid of the diode. Thank you for the tip.

BertB

You might be right. I will check tonight.

BertB

Hi, Just add: ina219_i2caddr = Settings.TaskDevicePluginConfig[event->TaskIndex][0]; So that PLUGIN_READ changes into: case PLUGIN_READ: { // shuntvoltage = Plugin_027_getShuntVoltage_mV(); // busvoltage = Plugin_027_getBusVoltage_V(); // current_mA = Plugin_027_getCurrent_mA(); // loadvoltage = Plu...

BertB

Hi,
Is the WS4050 supported?

BertB

Hi. I never tested IT with a advanced version, so that can be a Challenge. If you don't get any data on rx or tx, you can try to make the tx and rx fixed. I showed how to do that some posts back.

BertB

I changed the code a bit, again. Unfortunately I can still not put it in the ESPEasyPluginPlayGround. For some reason I cannot upload any more pics, zo, there is a link below. The changes are that it better communicates with the Nextion. I adapted the Hollyberry HMI file. https://www.dropbox.com/s/t...

BertB

This type is defined in the ESPEasy.ino. #define SENSOR_TYPE_SINGLE 1 #define SENSOR_TYPE_TEMP_HUM 2 #define SENSOR_TYPE_TEMP_BARO 3 #define SENSOR_TYPE_TEMP_HUM_BARO 4 #define SENSOR_TYPE_DUAL 5 #define SENSOR_TYPE_TRIPLE 6 #define SENSOR_TYPE_QUAD 7 #define SENSOR_TYPE_SWITCH 10 #define SENSOR_TYP...

BertB

Hi Marko,
Yes, you have to copy the code in this thread into a file named _P117_Nextion.ino.
I use wordpad for that.
Save that file in the ESPEasy folder.
Start the Arduino IDE, complie and flash.

That should be it.

BertB

This works very well too.

BertB

Ah ... I am going to try that tonight

BertB

I am trying to get the input from buttons as follows: For example, in the Nextion, I have put the following lines in the Tough Release Event section of a button: if(va1.val==0) { va1.val=1 print "|s" print "idx=99&switchcmd=On" printh 0a }else { va1.val=0 print "|s"...

BertB