Search found 771 matches
- 01 Apr 2020, 16:17
- Forum: RFlink: General Discussions
- Topic: RFLink + IRremote ?
- Replies: 4
- Views: 23772
Re: RFLink + IRremote ?
No. An extra Arduino costs ~5 euros
- 01 Apr 2020, 14:50
- Forum: RFlink: General Discussions
- Topic: RFLink + IRremote ?
- Replies: 4
- Views: 23772
Re: RFLink + IRremote ?
No, RFlink does not have support for Infra Red.
- 31 Mar 2020, 23:25
- Forum: RFLink: French support forum
- Topic: X2D et tydom 520
- Replies: 9
- Views: 15883
Re: X2D et tydom 520
Since RFLink did not change at all, something must be causing interference in the RF signals.
Check if all other sensors are workign correctly. One might be sending garbage signals that interfere with the X2D signal
Check if all other sensors are workign correctly. One might be sending garbage signals that interfere with the X2D signal
- 30 Mar 2020, 19:37
- Forum: RFLink: French support forum
- Topic: X2D et tydom 520
- Replies: 9
- Views: 15883
Re: X2D et tydom 520
If it was working before then check the battery level of your device.
Low battery can corrupt the transmitted signal.
Low battery can corrupt the transmitted signal.
- 30 Mar 2020, 16:39
- Forum: RFLink: French support forum
- Topic: X2D et tydom 520
- Replies: 9
- Views: 15883
Re: X2D et tydom 520
Oviously your door detector is not supported yet.
Mail a debug log to me as expolained here:
http://www.rflink.nl/blog2/development
Mail a debug log to me as expolained here:
http://www.rflink.nl/blog2/development
- 13 Mar 2020, 17:26
- Forum: RFLink: Hardware Related discussions
- Topic: RFLink with NodeMCU, readings are not sent on wifi
- Replies: 59
- Views: 91692
Re: RFLink with NodeMCU, readings are not sent on wifi
Perhaps a lot of resets..? This is likely. Indeed, the firmware sends two commands to RFLink at startup : 10;ping; and 10;version; rflinkSerialTX.println(F("10;ping;")); // Do a PING on startup delay(100); rflinkSerialTX.println(F("10;version;")); // Ask version to RFLink After ...
- 13 Mar 2020, 00:48
- Forum: RFLink: Hardware Related discussions
- Topic: RFLink with NodeMCU, readings are not sent on wifi
- Replies: 59
- Views: 91692
Re: RFLink with NodeMCU, readings are not sent on wifi
Perhaps a lot of resets..?
- 10 Mar 2020, 12:09
- Forum: RFLink: Nederlands support forum
- Topic: tx timeout
- Replies: 31
- Views: 51256
- 03 Mar 2020, 23:27
- Forum: RFlink: General Discussions
- Topic: RFLink "wiki" down?
- Replies: 6
- Views: 27723
Re: RFLink "wiki" down?
No, it still runs stable here..
the rflink blog is here: www.rflink.nl
the rflink blog is here: www.rflink.nl
- 09 Feb 2020, 01:07
- Forum: RFLink: Nederlands support forum
- Topic: RFLink "bevriest"
- Replies: 4
- Views: 29668
Re: RFLink "bevriest"
Die gaan vaak als een dolle signalen zenden die als stoorzender over komen
- 08 Feb 2020, 15:35
- Forum: RFLink: Nederlands support forum
- Topic: RFLink "bevriest"
- Replies: 4
- Views: 29668
Re: RFLink "bevriest"
Mogelijk een device op batterijen die bijna op zijn..
- 06 Feb 2020, 17:22
- Forum: RFLink: Unsupported devices
- Topic: Ventilation System and garage door.
- Replies: 11
- Views: 16841
Re: Ventilation System and garage door.
If it is recognized as Keeloq then you can receive but not transmit.
- 30 Jan 2020, 13:53
- Forum: RFLink: Hardware Related discussions
- Topic: Check Part List
- Replies: 3
- Views: 29342
Re: Check Part List
If your sensors are not listed on
http://www.rflink.nl/blog2/devlist
then it is unlikely that the signals will be detected.
http://www.rflink.nl/blog2/devlist
then it is unlikely that the signals will be detected.
- 29 Jan 2020, 22:40
- Forum: RFLink: Hardware Related discussions
- Topic: Check Part List
- Replies: 3
- Views: 29342
Re: Check Part List
Here: http://www.rflink.nl/blog2/wiring you can find all the modules and how to wire them. If it is not listed there, it is not tested. The STX is mentioned but make sure you have a proper power converter for the 3.6 volts that it will need. Why not just go for one of the listed modules? Will cost y...
- 11 Jan 2020, 01:51
- Forum: RFlink: General Discussions
- Topic: RFLink Livolo IDs and Unit Codes
- Replies: 2
- Views: 30435
Re: RFLink Livolo IDs and Unit Codes
What you are trying to do is not possible.
For RFlink there is no Livolo setting in Domoticz.
Read: http://www.rflink.nl/blog2/faq
and scroll to
Q: how to create devices in Domoticz without the original remote control?
For RFlink there is no Livolo setting in Domoticz.
Read: http://www.rflink.nl/blog2/faq
and scroll to
Q: how to create devices in Domoticz without the original remote control?
- 08 Jan 2020, 14:57
- Forum: RFlink: General Discussions
- Topic: Somfy soliris rain and windsensor
- Replies: 2
- Views: 26047
Re: Somfy soliris rain and windsensor
Sure, make a debug log and mail that.
See description here: http://www.rflink.nl/blog2/development
See description here: http://www.rflink.nl/blog2/development
- 06 Jan 2020, 14:39
- Forum: RFlink: General Discussions
- Topic: Serial issues?
- Replies: 5
- Views: 12634
Re: Serial issues?
Does the ESP add CR/LF (carriage return/line feed) to the commands that go to RFlink?
- 22 Dec 2019, 23:48
- Forum: RFlink: General Discussions
- Topic: KaKu awst-6000 en APIR-2150 (2019) not detected by RFLink
- Replies: 6
- Views: 41748
Re: KaKu awst-6000 en APIR-2150 (2019) not detected by RFLink
we are looking into it
- 22 Dec 2019, 23:47
- Forum: RFlink: General Discussions
- Topic: Issue with multiple BrelMotors
- Replies: 2
- Views: 26309
Re: Issue with multiple BrelMotors
Make a debug log as described on the rflink homepage to get this sorted out.
- 04 Dec 2019, 09:53
- Forum: RFlink: General Discussions
- Topic: OWL CM180i Reads 0W
- Replies: 2
- Views: 26992
Re: OWL CM180i Reads 0W
http://www.rflink.nl/blog2/download
make a debug log and mail that to me
make a debug log and mail that to me
- 30 Nov 2019, 00:03
- Forum: RFLink: Unsupported devices
- Topic: Atlantic MD-334R Alarm horn
- Replies: 12
- Views: 42002
Re: Atlantic MD-334R Alarm horn
Read the latest post on http://www.rflink.nl/blog2/ If you have ANY device that can transmit to your Sirene/horn then make a debug log and mail that. We need RFLink debug data, plenty of others supply debug data! If you can not provide that then we are forced to first look at the debug data that we ...
- 08 Oct 2019, 23:26
- Forum: RFlink: General Discussions
- Topic: No Milight Pairing option
- Replies: 2
- Views: 29097
Re: No Milight Pairing option
Do the pairing within RFlink Loader!
Do NOT use the manual create rflink devices option.
That is only used to instruct the home automation software what your devices are.
There is no RF function linked to it at all.
Do NOT use the manual create rflink devices option.
That is only used to instruct the home automation software what your devices are.
There is no RF function linked to it at all.
- 07 Oct 2019, 16:49
- Forum: RFLink: Unsupported devices
- Topic: 433 mhz switch cheap "intertek"
- Replies: 1
- Views: 30786
Re: 433 mhz switch cheap "intertek"
There are so many cheap devices that are working fine..
Maybe you should have purchased one from the list.
Anyway, read here waht to do:
http://www.rflink.nl/blog2/development
Maybe you should have purchased one from the list.
Anyway, read here waht to do:
http://www.rflink.nl/blog2/development
- 22 Aug 2019, 18:19
- Forum: RFlink: General Discussions
- Topic: Somfy RTS - some blinds don't fully open
- Replies: 4
- Views: 32007
- 14 Aug 2019, 15:02
- Forum: RFlink: General Discussions
- Topic: Registering RFLink as a new remote to KaKu devices
- Replies: 3
- Views: 31135
Re: Registering RFLink as a new remote to KaKu devices
Try:
10;NewKaku;cac142;1;ON;
10;NewKaku;cac142;2;ON;
10;NewKaku;cac142;3;ON;
10;NewKaku;cac142;1;ON;
10;NewKaku;cac142;2;ON;
10;NewKaku;cac142;3;ON;
- 13 Aug 2019, 20:56
- Forum: RFlink: General Discussions
- Topic: 3 second delay (only) for the same signal/sensor?
- Replies: 2
- Views: 30095
Re: 3 second delay (only) for the same signal/sensor?
There is a mechanism to prevent reporting of double states. However, this is only for the same sensor and the same state. Indeed as you noticed this means that 2 different sensors can send very shortly after eachother as far as it concerns RFlink. It also means that, again for RFlink, the same senso...
- 13 Aug 2019, 17:52
- Forum: RFlink: General Discussions
- Topic: Registering RFLink as a new remote to KaKu devices
- Replies: 3
- Views: 31135
Re: Registering RFLink as a new remote to KaKu devices
Yes you can.. just pick a more or less valid ID and send the ON signal while the ASUN is in pairing mode.
- 28 Jul 2019, 11:43
- Forum: RFLink: Unsupported devices
- Topic: Atlantic MD-334R Alarm horn
- Replies: 12
- Views: 42002
Re: Atlantic MD-334R Alarm horn
It depends on how and what if it can be send or not. However: 10;Atlantic;010E02;8;08200804010E020900; this is for sure not a valid format. The last part (in your case 9 bytes) must be a command, like ON or OFF. Testing at random will not work. You need to get a value from a device (like a remote or...
- 25 Jul 2019, 18:48
- Forum: RFLink: Unsupported devices
- Topic: Atlantic MD-334R Alarm horn
- Replies: 12
- Views: 42002
Re: Atlantic MD-334R Alarm horn
That might work.. but it is possible that there are restrictions on the ID.
Best would be if someone has a valid ID that he can share.
Best would be if someone has a valid ID that he can share.
- 25 Jul 2019, 15:07
- Forum: RFLink: Unsupported devices
- Topic: Atlantic MD-334R Alarm horn
- Replies: 12
- Views: 42002
Re: Atlantic MD-334R Alarm horn
The horn should learn (with the register button) the code (id) from a remote control or alarm base station..
You do not have something that can trigger the horn?
You do not have something that can trigger the horn?
- 09 Jul 2019, 20:22
- Forum: RFlink: General Discussions
- Topic: development stuck/still alive?
- Replies: 7
- Views: 38009
Re: development stuck/still alive?
Here we go again.. post removed.. watch your language!
This thread is now closed.
For those interested, development continues.
This thread is now closed.
For those interested, development continues.
- 02 Jul 2019, 18:07
- Forum: RFlink: General Discussions
- Topic: missing update from WH5029
- Replies: 4
- Views: 35434
Re: missing update from WH5029
Hi, make a debug log and mail that to frankzirrone@gmail.com
- 27 Jun 2019, 01:05
- Forum: RFLink: Unsupported devices
- Topic: Oregon OSV3 protocol - wrong ID
- Replies: 5
- Views: 13528
Re: Oregon OSV3 protocol - wrong ID
Derek, first get a real RFLink..!
Then you will see that your devices are detected
Then you will see that your devices are detected
- 27 Jun 2019, 01:01
- Forum: RFlink: General Discussions
- Topic: RFLink + Arduino UNO + Oregon THN132N
- Replies: 1
- Views: 32006
Re: RFLink + Arduino UNO + Oregon THN132N
1. You are using an Arduino UNO, RFlink is only designed for the Arduino Mega. 2. You are using a cheap chinese RF receiver. See: http://www.rflink.nl/blog2/wiring to know what RF modules to use and also why not to use the module you have. 3. The code you are referring to is not my project and obvio...
- 26 Jun 2019, 09:14
- Forum: RFlink: General Discussions
- Topic: RF Link and the Vera controller
- Replies: 2
- Views: 31916
Re: RF Link and the Vera controller
No idea.. I had it working on Vera 2
- 21 Jun 2019, 16:50
- Forum: RFlink: General Discussions
- Topic: X10Secure support question
- Replies: 3
- Views: 32717
Re: X10Secure support question
I believe there is. That would be very nice, so I guess me not seeing them as devices is a Domoticz issue then rather than an RFlink one? >If so, can I also SEND Yes. >If so, can I also simulate X10 security sensors? Yes. >If NOT, is this something that could be added? Yes. Ok, guess I will need to...
- 21 Jun 2019, 13:31
- Forum: RFlink: General Discussions
- Topic: X10Secure support question
- Replies: 3
- Views: 32717
Re: X10Secure support question
I believe there is. >If so, can I also SEND Yes. >If so, can I also simulate X10 security sensors? Yes. >If NOT, is this something that could be added? Yes. Note that "secure" in terms of actual security is: zero, nihil, null, void ... When you can send/replay RF commands like with rflink ...
- 03 Jun 2019, 17:36
- Forum: RFlink: General Discussions
- Topic: R45 - 433MHZ Send Doesn't Work Anymore
- Replies: 5
- Views: 7505
Re: R45 - 433MHZ Send Doesn't Work Anymore
It was a specific issue back in 2017 with a very old release.
This is no longer relevant for the current release version.
This is no longer relevant for the current release version.
- 30 May 2019, 10:13
- Forum: RFlink: General Discussions
- Topic: development stuck/still alive?
- Replies: 7
- Views: 38009
Re: development stuck/still alive?
>no answers from forum no answers from email no answers to help ... You send at least 4 messages about an elepowstar doorbel... and not all of them that friendly. You even received an answer that we are looking into it. >it s very unfair from the man/group who initiated this project to to drop those...
- 20 May 2019, 14:37
- Forum: RFlink: General Discussions
- Topic: Problem with keypress ever 1 sec
- Replies: 2
- Views: 4371
Re: Problem with keypress ever 1 sec
Nothing.
Pressing a button just shortly or pressing it very long does not generate a different signal.
This means RFlink does not need to repeat the same signal over and over.
All works as expected.
What do you believe is wrong then?
Pressing a button just shortly or pressing it very long does not generate a different signal.
This means RFlink does not need to repeat the same signal over and over.
All works as expected.
What do you believe is wrong then?
- 16 May 2019, 15:13
- Forum: RFLink: Unsupported devices
- Topic: FirePlace Jolly Mec
- Replies: 5
- Views: 13670
Re: FirePlace Jolly Mec
Do you always get the same 2 lines of data when pressing a button?
Can you post these 2 lines for the 2 main buttons (like on/off)
Can you post these 2 lines for the 2 main buttons (like on/off)
- 13 May 2019, 10:05
- Forum: RFlink: General Discussions
- Topic: More than 16 RTS remotes
- Replies: 3
- Views: 5362
Re: More than 16 RTS remotes
The next release has support for 32.
- 29 Mar 2019, 16:03
- Forum: RFlink: General Discussions
- Topic: So many questions and no answers ? the forum is dead or not ?
- Replies: 3
- Views: 5936
Re: So many questions and no answers ? the forum is dead or not ?
Most answers can be found here: http://www.rflink.nl/blog2/faq or in your case here : http://www.rflink.nl/blog2/devlist You asked questions about products (doorbell) that are not in the supported device list. Guess what, if they are not listed as being supported and are not working when you try the...
- 26 Feb 2019, 00:13
- Forum: RFLink: Hardware Related discussions
- Topic: Rflinkloader fault
- Replies: 4
- Views: 10817
Re: Rflinkloader fault
are you sure all files from the archive are copied?
- 14 Feb 2019, 14:31
- Forum: RFLink: Development and announcements
- Topic: Send custom packet
- Replies: 7
- Views: 17015
Re: Send custom packet
No, we do not have fully custom packets. We only have the rffind feature for now.
- 14 Feb 2019, 14:29
- Forum: RFLink: Development and announcements
- Topic: Sending keeloq packets
- Replies: 2
- Views: 11796
Re: Sending keeloq packets
The button identification is not encoded, thats why RFLink can see it.
However, the Rolling Code is encoded, thats why RFlink can not send with this protocol.
It would required a decryption key to decode the rolling code. This key is different for every device.
However, the Rolling Code is encoded, thats why RFlink can not send with this protocol.
It would required a decryption key to decode the rolling code. This key is different for every device.
- 26 Jan 2019, 13:44
- Forum: RFLink: Nederlands support forum
- Topic: Smanos x500 domoticz
- Replies: 3
- Views: 11099
Re: Smanos x500 domoticz
Hier staat wat je moet doen als devices niet worden weergegeven:
http://www.rflink.nl/blog2/development
http://www.rflink.nl/blog2/development
- 17 Jan 2019, 12:19
- Forum: RFLink: Hardware Related discussions
- Topic: Selectplus doorbell issue
- Replies: 2
- Views: 10488
Re: Selectplus doorbell issue
We are working on a fix for that..
- 13 Jan 2019, 14:58
- Forum: RFlink: General Discussions
- Topic: Temp / Hygro F007TH troubles
- Replies: 5
- Views: 7360
Re: Temp / Hygro F007TH troubles
RFlink does not transmit F007 or any other weather station signals.. it only receives..! If you want to try a RX/TX module that is untested/unlisted then you should probably also get one of the listed modules for reference.. like the rbx6 or so. Make sure devices are not too far away when testing bu...
- 08 Jan 2019, 19:51
- Forum: RFlink: General Discussions
- Topic: How to change direction of Somfy roller shutters
- Replies: 3
- Views: 9286
Re: How to change direction of Somfy roller shutters
Isnt that something you can easily change in Domoticz?