Let's Control It

BerndJ

Hi, next test results: i disabled one of them, power off, seeing only two ESP_0 in Fritzbox. Changed the sending channel of the FB: these one, who had attached sensors changed also with his AP the channel to the new one, the other uses the old channel for his AP and followed only with his connection...

BerndJ

.... is already there. ...... Hi, shure? Testing 3x ESP-12E with R057, two whitout attached Sensors, these are running fine without resets (3031 and 3030 minutes), the last maked one reset (130 minutes ago) with OLED, 2x 18B20, BH1750, BMP085, DHT11 and analogue Measuring, all 3 are logged into the...

BerndJ

Hi Martinus, thx a lot for this great work, it´s better and i can live with it at ESP-01. Here some results of testing: ESP-01 Name 4) MAC: 18:FE:34:A1:B2:E9 Flashing OK, running itself and OK, reboot via serial Line: wdt und hangs, Hardwarereset: OK, Reset via serial Line: löscht, schreibt und renn...

BerndJ

Hi,

what is the best solution to use I2C on the ESP-01 Module??

GPIO0 SDA and GPIO2 SCL

or

GPIO0 SCL and GPIO2 SDA

BerndJ

Searching for best ? way for running:

Hi,

ooh, this price is very good, but 60 days if i get these parts

, chinese Horror regarding Dev. , until this the market is another, or did the praxis by yrself tell another?

cleaning flash with x00 or xFF ?

and what is with the rest of 2 MB Flash?

BerndJ

Hi mkotec,

nice, but let´s found the reason why?

Which PCB selected? "Generic ESP 8266 Module" or "NodeMCU 1.0"

and if Generic which Flash Size

thx

PS: one sealed brand new marked:
0616
SKU237303 EVU

are here in my fingers, did u had information about yours

BerndJ

next confusion Take the first 01 and it runes, saying normal boot ?? Flash your ESP_Flastest and see no difference to the other one with the problems. Flashing back to R052, it´s booting and says Normal boot and connecting. Make a hardware reset, another booting: INIT : Boot OK INIT : RTC not read b...

BerndJ

Hi, next wunderground: flashed R052 again on ESP-01, booted not right, terminal says wdt reset. Press the resetbutton: INIT : Booting Build nr:52 WIFI : Connecting... INIT : I2C INIT : Boot OK INIT :[u] Reboot from deepsleep[/u] >settings System Info IP Address : 192.168.113.194 Build : 52 fine, it´...

BerndJ

Hi Martinus, so, i had tested 2 ESP-01 on my own PCBs. First: old version R027 flashed to R052. It runs at the first boot and loggeg into my WLAN. Second one: old version R032 flashed to R052. Runs, but not loggeg into the wlan. sending "settings" via serial Line and see IP: 0.0.0.0. Hardw...

BerndJ

Hi, same problems at mine. The R052 is a little bit better but solve (Incorrect PID or version!, see Routine Line 336 to 345 ESPEasy.ino, V051 information in row 329 and 330) not the problems. How do u flash your ESP-12E and what kind of module is it? I had three Node MCU, i think the last version, ...

BerndJ

Hi, nice, thx a lot. Is it planend in future to send Messages via http request, like: http://<ESP IP address>/control?cmd=OLED,<line nr>,<pos nr>,<Text> ?? Would be nice also for the LCD Display. Or could i send such Messages via json or something else? best wishes BerndJ PS: I found 0,96" and ...

BerndJ

Hi, yes, done since version 042 in test phase. It would be nice if the developer could explain a little bit to these level control device in the Basic sketches in the homepage. But i thing it´s not possible to make an AND or OR check to two values, it´s look that only one value is possible. I dream ...

BerndJ

Hi,

u could set the ports under the tab Hardware.

BerndJ

Hi,

no problem

BerndJ

Hi,

a third brach on github could be fine.

BerndJ

Hi,

they use the 8574 for the lcd display on port 0x27.

Best is u use the MCP23017, double ports and the possibility of 8 pieces.

And, ... it´s running.

Don´t forget the pull-up resistor in the reset line.

BerndJ

BerndJ

Hi NietGiftig, ".. if the el-cheapo switches (Impuls Action)....". Did u had a link? The used chip in the transmitter is a HX2262, normally designed for IR Remotes. U can recogniced them at the 5 DIP Switches in the transmitter, i thought these parts are the lowest-cost on the market. best...

BerndJ

Hi jdoESP, Sorry, but: Mmm I'm afraid I'm not so fit yet ;) , also ;) ;) Take a look of the kind they are programming (source code), it´s fantastic and u can learn a lot. And then test to prog by yourself. I haved done it for more Times: PCA9532, PCA9685 and PN532. Now i take a look to prog 433 MHz,...

BerndJ

Hi, there are no driver, but u can create one, test it and make a pull request. If the test would be fine these boys integrate these output modul, make a new revision and i´m also bee happy. possible basic Drivers can be found here: https://github.com/adafruit/Adafruit-PWM-Servo-Driver-Library best ...

BerndJ

Hi, very good idea, thats the right way. At first i would like to control the windows shutter. separate switch at each window (cables existing), MCP23017 input to esp and these software to toggle 2 outputs, also on 23017 for action. info to centralized Homecontrol and the WAF is OK. We should includ...

BerndJ

Hi,

u had it done, thx a lot.

fantastic work, R040 and it´s running.

Bernd

BerndJ

Hi,

3 Cables, one 433 MHz Sending Modul and one ESP, and it´s running fine:

https://alexbloggt.com/funksteckdosenst ... t-esp8266/

The used library also supports receiving.

best wishes

BerndJ

BerndJ

Hi Bert, thx a lot, looks nice and hope it helps some-, one, more ore everybody. Next: http://www.esp8266.nu/index.php/TemperatureSensor ... can read ___ a ____ Dallas .... ... Since Version V022 you could connect up to 12 Sensors. a problem regarding negative values are solved since V032. and regar...

BerndJ

Hi, I think it´s time to expand the wiki, because failures can, should and whould be produced for once, the second one is one to much! we need a tab under Hardware: bullshit, born in praxis I begin with DHT11 http://www.esp8266.nu/index.php/HumiditySensor avoid to use it on GPIO15, why? in boot mode...

BerndJ

http://sourceforge.net/projects/espeasy/files/

BerndJ

Hi, had a pull up (value pls?) resistor in use on GPIO2, give us the lenght of the cable, what cable it is and the time how long u wait for a response to the sensor ? Helps to solve the problem. I had V034 ,gpio0 in use, using 1 KOhm as PullUpR with a lenght of 20 cm to 2 pcs of DS18B20 and had no p...

BerndJ

Sorry, i must bee blind, do´nt see any solution regarding these problem on these site. Take a resistor and a led, put it to one port and send the command with level 3 to this port. Did u had a constant Light?? I had testet some boards, all of them have these problem, the led flashes. If i send level...

BerndJ

Hi, done, what did i not see? http://<ESP IP address>/control?cmd=PWM,13, 1 and also up to http://<ESP IP address>/control?cmd=PWM,13, 5 and the output Pin GPIO13 flashes, no constant level. http://<ESP IP address>/control?cmd=PWM,13, 0 and up of http://<ESP IP address>/control?cmd=PWM,13, 6 is OK. ...

BerndJ

Hi,

i had a little bit problems at and up V030, but i´m thinking thats because i´m using the 3 "problem" (GPIO 0, 2 and 15) ports.

Bernd

BerndJ

Hi,

i´ve got no problems, but uses more ESP-12E with 4 MB Flash.

Bernd

BerndJ

Hi, had a problem when i would like to use the PWM function by the above mentionend values. greater value 5 everything works fine. is it a esp problem? Idea: nice and a dream could be a dimming function, like: http://<ESP IP address>/control?cmd=Dim,<pin>,<Startlevel>,<Endlevel>,<time> best wishes B...

BerndJ

I found something, Manual: https://dangerousthings.com/wp-content/uploads/2013/12/PN532_-Manual_V3.pdf Libs: https://github.com/elechouse/PN532 NXP User Manual: http://www.nxp.com/documents/user_manual/141520.pdf Schematics: http://www.elechouse.com/elechouse/images/product/PN532_module_V3/PN532_she...

BerndJ

Hi, i had here a sample of: NXP PN532 NFC RFID Module V3 Kits Reader Writer For Arduino Android Phone TE314 buyed on ebay for 17€ it´s possible to select I2C Bus. also SPI and serial Communication. I see him on the bus when i scan it on port 24, and for the first time on 24 and 25. Do you plan to in...

BerndJ

Hi, last night same problems. I found only two devices on the 1-Wire Bus. cable problems at one sensor are the problem. the ESP device sends 3 values!!, one are doubled. After solving the cable problem we had problems regarding the third one. The 3 was on position 2 and old position 2 i could see on...

BerndJ

Hi, I thing we had a problem regarding the values of the different sensors and the sending to their corresponding parameters. It´s look like a ESP with dementia. Attached are one file of the output. At first 3 Sensors are online, i put one away and hoped that these sensor got none value. These probl...

BerndJ

Hi @ all, my name is Bernd and i´m living in the north of germany, near Hamburg. 58 yrs old sack just like Bert, the hole time a little bit crazy regarding homecontrol. tech and business degrees. And no, i dont use domoticz, heart 2 weeks ago while i´m stumpled about yr projekt. Using IP-Symcon http...

Search found 86 matches

Re: Disable the ESP config AP?

Re: Disable the ESP config AP?

Re: ESP-12E not able to memorize WiFi AP data

Re: I2C on GPIO 0 + 2

Re: ESP-12E not able to memorize WiFi AP data

Re: ESP-12E not able to memorize WiFi AP data

Re: ESP-12E not able to memorize WiFi AP data

Re: ESP-12E not able to memorize WiFi AP data

Re: ESP-12E not able to memorize WiFi AP data

Re: ESP-12E not able to memorize WiFi AP data

Re: OLED I2C

Re: Wishfull thinking

Re: LCD and BMP085 operate paralel?

Re: LCD and BMP085 operate paralel?

Re: Discussion on local control by ESP Easy

Re: support for PCF8574 ?

Re: 433 MHz Transmitter & Receiver

Re: ESP8266=> I2c=> PCA9685 => 12 Servos

Re: ESP8266=> I2c=> PCA9685 => 12 Servos

Re: Discussion on local control by ESP Easy

Re: Support for I2C RFID Reader NXP PN532

433 MHz Transmitter & Receiver

Re: DHT: let´s grow the WIKI, by bullshit born in praxis

DHT: let´s grow the WIKI, by bullshit born in praxis

Re: Need a Build R20 With all

Re: NAN when reading DS18b20

Re: PWM, Value 1 to 5 flashes

Re: PWM, Value 1 to 5 flashes

Re: Will not run after R32 Update

Re: Will not run after R32 Update

PWM, Value 1 to 5 flashes

Arduino Libs

Support for I2C RFID Reader NXP PN532

Enlighning

diced Values

BerndJ from germany