on my side i found a great nodemcu app : This create a milight wifi rgb led strip controler. https://github.com/frizzby/esp8266-rgb-led i run it on a wemos mini d1 and just a led plug on gpio0 + gnd this made for a "classic" led strip. Maybe some one can test it on this hardware H801 Hard...

I have one of these and have soldered wires to all 4 pads. I am having issues uploading easy ESP to it though. Can someone go into a bit more detail for me? Hi, what's the problem? Not flashing or doesn't run after flashing? The problem is not flashing. I've used the 4 pads on the bottom of the boa...

jay_s_uk wrote:I have one of these and have soldered wires to all 4 pads. I am having issues uploading easy ESP to it though.
Can someone go into a bit more detail for me?

Hi, what's the problem? Not flashing or doesn't run after flashing?

Hi! Just wanted to check something. If i'm updating over the air onto a device with 1mbyte flash, I take it I should use 1meg with 512k spiffs when compiling? Also, why does it lose all its settings? Is it because the temp new image overwrites the setting on the chip? I mean, there isn't enough room...

ambassadoro wrote:

cherowley wrote:Hiya costo,

I was trying to get a pir sensor working with it last night but no joy @ 3v..
!

The usual PIR-sensors from ali can be hacked to work with 3.3V. Maybe thats worth a try.

Ah that's what i was doing, thanks anyways

4refr0nt wrote:

I'll try 2.0.0.0 community if I find out the new url - mine just gives 1.6.5

2.0.0

Cheers, found it and compiles ok

R78 is meant to be used with the libraries packed with the R48 release Please, give me proof from developers :D Yes I agree, it can't be the same as r048 - r048 compiling didn't give this error: ESPEasy.ino:179:37: fatal error: ESP8266HTTPUpdateServer.h: No such file or directory ;) I'll try 2.0.0....

Hi, I would also like to build r078 from source but the files aren't correct for r078.. R078 asks for libraries that were not in r048. Where to get the correct libraries from as: a) Some new libraries are used. b) some previously used libraries in r048 must have been changed in r078 as r078 gives co...

Hiya costo,

I was trying to get a pir sensor working with it last night but no joy @ 3v..

Where are you picking 5v up from?

cheers!

Morning Costo!

I haven't had chance yet to mod the code but looks like you've beaten me to it anyway!

If i get time today i'll grab yours and give it a go

Yep the board does look the same as that picture

In the circuit diags it showed 5 pins in the header but only 4 in the actual board...

Ah, if the code only requires turning off the serial output and adding them to the drop down list i'll have a dabble

Hi costo,

Yeah the board is different from the circuit diags found on the web...

Of course, could we change the espeasy code to disable the serial port and use those 2 lines for i2c? Is it just a software thing or do we need to put the esp chip in a different hardware mode to disable the uart?

I've modded some of the source code and have fading working, after a fashion. It's not that smooth due to having a linear fade and also just being in the main loop. No error checking either as not bothered going beyond rough alpha coding due to poor performance. I have edited _p001_Switch.ino, WebSe...

Mine have arrived and sad to say that the circuit diagrams online do not match the actual unit so no gpio line broken out to the pads (only 4 pads not 5 pads).

So maybe use gpio 0 from the switch and the led (shorting the current limiter resistor) as the i2c pair?

Many thanks voyager for that suggestion, tried it now but unfortunately it doesn't repeat quickly enough. Plus straight after sending the on code I need to send the off code (for home easy devices)..

Hi! I would like to setup a manual switch in domoticz then put a home easy light dimmer in learn mode and get it trained but most devices, not just home easy, need you to keep your finger on the remote button for a few second thus repeating the code multiple times until leaning is complete. Is this ...

Not sure about hardware pwm but I'm experimenting with adding a PWMFADE command. Simply PWMFADE,GPIO,TARGETLEVEL

This is for R048

I've ordered a few of these and plan to flash with easyesp too.

Hope to use the gpio 0 for input (making sure it's not pressed during boot of course..

Got mine working by grounding the metal of the light fitting and covering the pir sensor in foil and making sure the foil touches the metal of the light fitting.

+1

Would be useful for adding sensor inputs to the commercial H801 rgbww dimmer...

Hi mkotek,

Ah ha! Synology does in fact have curl! This may be very useful and allow sending 0's and 255's from the command line! (Synology doesn't have netcat)

Cheers!

How about setting up a virtual dimmer switch in domoticz called "Dimmer Strip Test" then using a lua script? Something like this: commandArray = {}; IP = '192.168.2.161'; Port = '80'; GPIO = 4; DomDevice = 'Dimmer Strip Test' print("ESPEasy Dimmer Strip Test Script") function sen...

Interesting stuff!

I've since managed to get the one in the ceiling light working- connected the metal of the lamp to ground..

Hi!

What software will you be using to control the modules? Domoticz?

Hiya! I'm trying to use one of these pir sensors but keep getting false triggers every few minutes or sometimes several times per minute... I've tried different psu, separate psu, moving the sensor away from the esp and wrapping the sensor in foil... Anyone have any other ideas? I'm now using a flas...