Let's Control It

riker1

Hi

having a questions:
what exactly is this message?

<3>1 2019-05-22T11:43:29.887978+02:00 ESPHOST EspEasy - - - EspEasy: HTTP : connection failed

what is the root cause?
what is the rule behind it?
Is it outgoing or incoming?
does this mean mqtt connection or which connection?

Thanks

riker1

Hi

what does or where does this message come from?

Code: Select all

Diconnet reason	(2) Auth expire

Code: Select all

STA MAC	60:01:94:5A:79:AD
AP MAC	62:01:94:5A:79:AD
SSID	TR7272 (26:A4:3C:DD:17:E1)
Channel	11
Connected	6 m 23 s
Last Disconnect Reason	(2) Auth expire

Thanks

riker1

grovkillen wrote: ↑21 May 2019, 14:58 You need to set up the recieving task/unit to be identical to the sending task/unit and have it send using the ESP Easy controller.

ok understood, thanks

riker1

Hi thanks but I do not understand how? when you say, task # , this is on ESP1 (receiving) I have a task there : lcd: will display WRC:[status_control#Wifi_Reconnect_Counter] but WRC:[status_control#Wifi_Reconnect_Counter] is send by both ESP 2 and ESP 3. So how to grab the WRC:[status_control#Wifi_R...

riker1

grovkillen wrote: ↑21 May 2019, 13:23 Unique unit numbers?

Unit Numbers are distinct.

Only same UDP Port.

but ...device names and variables ...?

riker1

sorry, no I mean,

esp1 receiving variable von both ESP2 and ESP3

device#variable names are same on esp2 und 3

How to separate those , showing them on LCD, on ESP1.

is it like:

[ESP2#device#variabe]?

Does this clarify?

T

riker1

Hi

I am wondering if it is possible to distinguish between 2 different devices .

Have 3 devices:
connect all via UDP Port

want to display some status values on ESP1.

ESP 2 and ESP 3 having same device name.

Can they be distinguished?
Or do I need unique device names?

Thanks

riker1

any idea how to further analyse this situatino? Three ideas: 1. Reboot the WiFi router. Check to see if the problem is resolved. 2. Monitor serial log until wifi has connected. Maybe the log messages will help with your troubleshooting. Be sure to disable serial log when you are done using it. 3. W...

riker1

Hi have a problem with an ESP Wifi reception is good: - ESP is custom LC Tech : ESP01S After some time webgui is opening again. System Info Value Unit: 143 GIT version: (custom) Local Time: 2019-05-13 07:32:51 Uptime: 0 days 2 hours 51 minutes Load: 23.80% (LC=19434) Free Mem: 10264 (3944 - ExecuteC...

riker1

Hi Martin,

thanks

I found an issue - as you said - in the device variable.

so mainly it is an user error

sendto is working.

Thanks very much
T

riker1

Hi

is it possible to switch backlight off via device config somewhere?

Display - LCD2004

Thanks

riker1

Hi I am unsing sendto and sendhttp but the eventvalues are not send. sendTo 149,event,disp_kt=[esp01_178_Temp#esp01_178_Temp] SendToHTTP 192.168.0.149,/control?cmd=event,http_kt=99 tried it wix fix value and variable from device. what am I doing wrong log shows: 197048: ACT : sendTo 149,event,disp_k...

riker1

07:52:11.251 -> 622 : WIFI : Not configured in Station Mode!!: xxxx 07:52:12.588 -> 1959 : WD : Uptime 0 ConnectFailures 0 FreeMem 25744 WiFiStatus 0 07:52:14.213 -> 3580 : WIFI : Disconnected! Reason: '(201) No AP found' Connected for 2858 ms 07:52:15.042 -> 4403 : WIFI : Connecting xxxx attempt #...

riker1

looks like somehow, wifi setting is not stored persistent

riker1

having still this issue with also robotdyn d1r2 wifi even having a static ip. 07:35:08.001 -> 615 : EVENT: System#Wake 07:35:08.001 -> 620 : WIFI : Set WiFi to STA 07:35:08.034 -> 653 : WIFI : Connecting TR7272 attempt #0 07:35:08.034 -> 654 : IP : Static IP : 192.168.7.1 GW: 192.168.0.31 SN: 255.25...

riker1

thanks Rob

riker1

Hi

what is the content of thoses:

Code: Select all

System status
%iswifi%
3	3
%isntp%
1	1
%ismqtt%
1	1
%ismqttimp%

Thanks for updating the wiki.
https://www.letscontrolit.com/wiki/inde ... _Variables
T

riker1

Hi

thanks

Was wondering is a

Code: Select all

wificonnect

would solve it ,
doing a reboot is more save?

riker1

Hi

ok thanks for the info and details provided

riker1

Hi

anyone knowing the reason for esp easy sending strange corrupt messages?

Code: Select all

����U��������U�������I�������������������������������������������������������������������������������������`��U��������������������������

thanks T

riker1

Hi

just curious if there is a big font option available for LCD2004?

Thanks

riker1

Hi reading https://espeasy.readthedocs.io/en/latest/Reference/Command.html and some forum threads I am unsure how to do a wifi reconnect. and also in combination with new advanced features: - Connection Failure Threshold: 60 Force WiFi B/G: Restart WiFi on lost conn.: situation: Having a lot of wifi...

riker1

ah ok understood
thx

riker1

Hi Thomas,

ok thanks

so command name
does not do anything

there is only on user : admin
no other users possible, right?

Thanks
T

riker1

Hi
I tried to change

name and password

https://www.letscontrolit.com/wiki/inde ... _Reference

but can not use those in the weblogin?

what am I doing wrong?

Thanks T

riker1

Hi

https://www.letscontrolit.com/wiki/inde ... _interface

I did set a admin password while flashing

but what is the user when logging into the webinterface?

How do I forward user and password using http requests?

did not find it in the wiki?

Thanks T

riker1

Hi Thomas

thanks working perfect!!

riker1

Hi

ok thanks.

that is right. I forgot those limitations.

It is working for gpio 3 and within rules

Thanks T

riker1

I checked with ESP01 and had a problem writing config data. so setting a device destroyed the config. Did you use PUYA-safe builds from the previous stable release on that chip? Hi formerly I used your firmware provided in post #196 https://www.letscontrolit.com/forum/viewtopic.php?f=6&t=3245&a...

riker1

Hi

could yo upost a template uploading rules?

It is not working for me.

Thanks T

riker1

Hi

I checked with ESP01 and had a problem writing config data.

so setting a device destroyed the config.

Looks like it is not working.

Any idea?

thanks T

riker1

Hi I did set hardware GPIO 0 to output low. after reboot. checking state, http://192.168.10.17/control?cmd=status,gpio,0 results in high 1: { "log": "", "plugin": 1, "pin": 0, "mode": "input", "state": 1 } why is hardware setting ...

riker1

ok perfect thanks will test it

riker1

also alphanumeric once?

Thanks

riker1

ok, that is perfect.

thanks

riker1

Hi is it possible to define a variabe - like : %ruleversion% = "version" which can be used later in publish command? I know the workaround to set a generic dummy device with event and eventvalue, but it would be easier to have a variable within rules to be used after flashing the rules . t...

riker1

ok thanks

so I can have similar event defined in rules 1 and call it from rule 2

same for timer. only 8 timers overall, start timer in ruleset 1 define timer event rules#timer in ruleset 2

Right?

Thanks a lot

riker1

Hi

I am wondering how the rule set 1 to 4 are related.

My understanding is, I can start a timer 1 or Monitor a GPIO 1 in Ruleset 1
and I can use the timer 1 or check state of GPIO 1 in rules set 2

or is my understanding wrong?

Thanks T

riker1

Hi

did try different power supplies but did not solve it.

riker1

Ok will try to reflash, having the problem: trying to connect espcomm_send_command: sending command header espcomm_send_command: sending command payload serialport_receive_C0: 46 instead of C0 trying to connect espcomm_send_command: sending command header espcomm_send_command: sending command payloa...

riker1

Hi I experienced a boot loop 15:17:35.058 -> INIT : Booting version: mega-20190305 (ESP82xx Core 2_4_2, NONOS SDK 2.2.1(cfd48f3), LWIP: 2.0.3 PUYA support) 15:17:35.091 -> 55 : INIT : Warm boot #33 - Restart Reason: Exception 15:17:35.091 -> 58 : FS : Mounting... 15:17:35.091 -> 63 : FS : Mount succ...

riker1

Hi I am struggling with the curl command

do you have an example please?

I assume it is a curl -u upload

Thanks thomas

riker1

Hi

I am having some witty esp modules.

some of those are not starting without the serial adapter attached.

anyone does know how to solve this?

maybe a certain pulldown?

Thanks T

riker1

Sounds great
Naming of Textfile Just rules1.txt?
Thanks

riker1

Hi

I am wondering if it would be possible to use the flash process remote
via json
or other methodes?

Thanks T

riker1

Hi in the reference https://www.letscontrolit.com/wiki/index.php?title=ESPEasy_Command_Reference wifiapkey is a valid command. running it : I got the errormessage : Unknown command! >WifiAPKey configesp Unknown command! strange or what am I doing wrong firmware: INIT : Booting version: mega-20190212...

riker1

Hi having esp serial connected and configured wifi via serial (Aruduino serial port tool) using dhcp mode via : ip 0.0.0.0 Wifissid ssid wifikey key after that I did a reboot. 665 : WIFI : Connecting TR7272 attempt #0 667 : WIFI : Not configured in Station Mode!!: TR7272 2002 : WD : Uptime 0 Connect...

riker1

is it possible to have an updated firmware? Sorry, the latest ESPEasy version i tested with this plugin is dated 2018.08.17 with core 2.4.0 and currently i have no time for testing. Core 2.4.1 and 2.4.2 is not working well with serial 2 way communication, and with 2.5.0 i have absolutely zero exper...

riker1

Hi could you please double check. Do not see FHEM as Controller? Yep, sorry i forgot, that i not just deleted the file, but removed my pluginset completely before. Recompiled. Hi is it possible to have an updated firmware? - required: controller: FHEM, MQTT, device: of courcse MCU relais - is it po...

riker1

hi
ok thanks,

so I can only use the event and set a own taskvalue for the status, right?

there is nothing like for GPIO to check the status?

thanks

Search found 344 matches