Let's Control It

riker1

Hi
I want to check if esp is still connected

having a looping trigger rule and wanted to check something like

wifi#connected=1

in an if statement.

but this is not working.

Log is not showing any hints to me.

how to use

Code: Select all

wifi connect status

in an if condition

thanks T

riker1

ok understood

riker1

ok thanks

riker1

Hi

is it possible to create a device via json or any other command?
or via flash?

thanks T

riker1

Hi

I trried this

but subscription is not working I think

please show your setting in :
controller subscription here:

thanks T

riker1

yes that is what I notified as well

riker1

Hi
is the heltec wifi kit with oled lcd supported by espeasy?

Thanks T

riker1

wifi setting is gone and I am looping into setup mode

riker1

I just had an similar error on another esp 01

release 20190212

saving wifi settings -> similar error message reading security dat 621

saving wifi settings fallback

riker1

it is working now for

Code: Select all

	mega-20190212

riker1

Hi

came from

Code: Select all

Mega-20181220

still testing not sure what the problem is

riker1

Hi

actually not
just new firmware flashed and tried to update it

riker1

Hi

I am facing an isue with : esp01 firmware

Code: Select all

mega-20190212

Code: Select all

error while reading/writing config.dat in 617

while saving controllers

Can not edit ip or ports

Any hints please

T

riker1

ok, thanks will try

riker1

Hi

how can I trigger a long press switch command via http or Mqtt?

Thanks T

riker1

Hi

I experienced an issue with chrome editiing rules.

sometime rule
- are not stored completely
- are not stored at all
- having an old / another content - former device, different rule #

when submitting

running chrome on ubuntu.

riker1

did serial reset . I would have expected a complete empty ESP but esp firmware still on it? RESET: Resetting factory defaults... using default settings RESET: Warm boot, reset count: 0 RESET: formatting... RESET: formatting done... RESET: Succesful, rebooting. (you might need to press the reset butt...

riker1

ok, i have to check serial command .....

riker1

Hi thanks problem is, it will connect to wifi and bring up the the website. I always have a authorization error , even if I change IP via serial console either to dhcp or static. I changed everything - SSID - IP static / dhcp So I have to set the settings back to factory without website. Thanks Thomas

riker1

Hi
I tried to erase all setting because I had a constant wifi problem with the robotDyn d1r2

even after flashing bare 4 mb minimum wifi config is retained.

but how?

how to delete everything?

Thanks T

riker1

riker1

Hi
is it possible to export and import a task/device ?

Thanks T

riker1

another question.

how can I set ip to dhcp via serial?

Thanks T

riker1

Hi after having auth expired , now I am having Disconnected! Reason: '(4) Assoc expire' Connected for 4749 ms new firmware deployed INIT : Booting version: mega-20190109 (ESP82xx Core 2_4_1, NONOS SDK 2.2.1(cfd48f3), LWIP: 2.0.3 PUYA support) 110 : INIT : Warm boot #4 - Restart Reason: Software/Syst...

riker1

that solved it. nice coonfiguration. perfect
thanks

riker1

Ah
perfect. will check this

that would be great

Thanks

riker1

Hi guys,

thanks for ESP and the great support always.

coffee on the way.
cheer T

riker1

The reason of the disconnect is just a standard reason returned by the wifi layer. Some are given by the accesspoint and some caused by the "user" like an intentional disconnect. As far as I know, the "Auth expire" is something related to a expired session. What ESP are you usin...

riker1

Hi
there is an new error message after I swapped to another SSID

Disconnected! Reason: '(4) Assoc expire' Connected for 4749 ms

riker1

Hi
nice, it is working.
Thanks

riker1

Hi
how can i select GPIO 1 and 3 (RX TX) for a switch.
Need this for ESP01 controlling relais.

Do not need serial but need 4 Gpios...

Thanks Thomas

Using latest firmware a the moment

Can this be enabled in Hardware section?

riker1

Hi I am having the same issue with a new firmware INIT : Booting version: mega-20190109 (ESP82xx Core 2_4_1, NONOS SDK 2.2.1(cfd48f3), LWIP: 2.0.3 PUYA support) 111 : INIT : Warm boot #2 - Restart Reason: Software/System restart 113 : FS : Mounting... 138 : FS : Mount successful, used 75802 bytes of...

riker1

thanks a lot

riker1

thanks

where do I find a list of available serial commands?

thanks Thomas

riker1

Hi I am experiencing with the wemos D1R1 strange wifi errors Disconnected! Reason: '(2) Auth expire' Connected for 3870 ms wifiscan does lead to all known SSIDs I tried it with firmware from November, December 2018 and Jan 2019 ESP_Easy_mega-20190109_normal_core_250_beta_ESP8266_4096.bin ESP_Easy_me...

riker1

ok, thanks will check that

Sounds great

riker1

Hi
I have a questions

How do I set IP
via Serial commands?

Thanks Thomas

do I just enter those command in console? putty?

Name ESP01S
Unit 202
ip xx.xx.xx.xx
WifiSSID ssid

etc?

I found it: just have to enter the commands in arduino serial command line.

Thanks

riker1

Hi

looks great.

Having a question:

I just want to use the 1x3 Matrix Array Key Membrane Switch Keypad 36x55mm (BTN-L,BTN-R,BTN-M)

How to I need to connect it and get readings for that?

I did

1 vcc
2 gnd
3. D2
4. D1

but do not get readings for it.
Thanks for Hints.

t

riker1

Hi
I have a similar issue.

just using a 3x keyboard. up down stop.

How to connect oin 1-4?
I did
1 - VCC 3V
2- GND
3.....SCL (serial clock in) D2
4.....SDO (serial data out) D1

No reading
just a static 1?

Thanks Thomas

riker1

Hi
maybe I missed this communication.
Did not find anything in WIKI

what about the new versions for core 2 4 and core 2.5?

- how to use those?
- any restrictions ?

Can I just deploy them onto the boards?

Thanks thomas

riker1

Seems to be a capacitive switch. If so it is supported by the "switch" plugin. Did a bit of research. It seems that the chip on the board (Marking 8223) is similar to the well known TTP223. Maybe a remake from another company? From layout it is not an inductive sensor but I may err. Anywa...

riker1

grovkillen wrote: ↑06 Jan 2019, 11:23 Which variable? The timer? If so, just use the command event,StartTimer=123 and change 123 to whatever number you want.

ok perfect, easier than I thought

riker1

ok thanks

riker1

ok thanks understood.
Nice aproach.

maybe a systemvariable for timers would be easier instead of duplicating it via dummy device.

another related questions. :is it possible to set the variable via mqtt?

Thanks Thomas

riker1

Hi
I am wondering if I can store a variable persistent in a flash part maybe config sections ?

thanks T

riker1

On StartTimer Do TaskValueSet,12,1,%eventvalue% TimerSet,1,%eventvalue% TimerSet,8,1 EndOn On Rules#Timer=1 Do TimerSet,8,0 TaskValueSet,12,1,0 //Whatever EndOn On Rules#Timer=8 Do TaskValueSet,12,1,[dummy#timeleft]-1 TimerSet,8,1 EndOn If you have your dummy on task number 12. Named dummy # timele...

riker1

hi, ok thanks, will check

riker1

Hi

would this be supported?

anyone having experience here?

Thanks

riker1

grovkillen wrote: ↑05 Jan 2019, 13:55 You would need to use two timers, one that is pushing the seconds passed to a dummy. But if you can explain the need for a system variable then we might implement it.

Hi ok, thanks.

but how do I push the seconds passed to the dummy? Would this work already?
or publish the seconds passed?

Thanks

riker1

Tommmii wrote: ↑15 Apr 2018, 15:39 yes, i am :p

Hi

and how?
which settings did you use?

Thanks

Search found 344 matches