Let's Control It

Dylantje

My 4 sonoff 4 channel flash data: Comport (example 3, 4, ..) :5 Flash Size (example 512, 1024, 4096) :1024 Build (example 71, 72, ..) :120 Using com port: 5 Using bin file: ESPEasy_R120_1024.bin esptool v0.4.6 - (c) 2014 Ch. Klippel <ck@atelier-klippel.de> setting board to nodemcu setting baudrate f...

Dylantje

is there perhaps a how to flash with the IDE.... I cannot flash 6 different sonoff with the espeasy flasher. Strange problem.. The flash tells me flash ok... Only no wifi to find. I try 120 and the last dev 2.0 With differnet boards. single dual and the 4 channel. Different flasgools Differnet usb f...

Dylantje

mmm Think my sensors had a bad connection...
I did remove the cable from the gpio.. Did some contact spray between them....
Now functioning ok for days....

Dylantje

Daer.... Sinds a few days my esp with dallas is not function correct any more. New powersuply.. is not do the job... everytime i reboot or power on/off the esp it working for 10/20 minutes.... Power off is working better to start the sensors then a reboot.. My esp is a... http://www.ayarafun.com/wp-...

Dylantje

Guys..
I am a Bob the Builder..
I was a hero when i flashed my first esp...
And my dual...

Only hope there is after a time wiki where i can see how i must acting...
This id for me higher math..

xxx
Love

Dylantje

we should be running fine with ESP Easy and Sonoff dual...

I think really there is something strange going on..

Cannot flash any Sonoff.
And i do have still running 6 esp flashed 3-4 times a few months ago without any problem...

Dylantje

mmm
Do you have a link for me to the other software?
So i can check my boards...
Perhaps i can see with the other software of my boards ar still working..

Dylantje

mm
Think i found the bad guy...

: ScreenShot054.jpg (132.91 KiB) Viewed 6374 times

: ScreenShot053.jpg (158.23 KiB) Viewed 6374 times

This was enabled and i think this disconect on servel times.... grrrr

I run now for a few days on disabled and there are no problem [ yet ]

...

Dylantje

did flash this software on my Sonoff dual. Looks great, only cannot get the switches find, what gpio are they use. I try all the gpio pins... Switch them with a dummy sensor in Domoticz. [ like my other esp, with Espaeasy ] Only no switching relay... Is there something else i need to do? And what ar...

Dylantje

mmm what pins can i use..
First the 2 for switching
And then what pin i have left for the fun thins?

Dylantje

mmm My serval esp function wel on the nice esp easy software. Only 1..... This 1 is after a few day disconnect from my Wifi signal. Is there perhaps a option to make the signal stronger, in the software? Perhaps a extra antenna? or perhaps a keep a live with the Wifi option? Or a reconnect setting, ...

Dylantje

the one you led see i do have to..
Time is here i try this one...

How to reset a board?
Only rf and tx by startup?
Or are there other options?

Dylantje

Did try with:
https://www.ebay.com/p/Pl2303ta-USB-TTL ... /574037578

And:
http://www.ebay.com/itm/RCmall-FT232-US ... Sw4CFYogca

Dylantje

Direct sunlight?

That is the only thing different...

mmm that's shoeld be nasty.....

1 pir have dig a cable to the door for this pir...
GGRRRRR

Perhaps with a 10K between..

The strange part. test works great...

Dylantje

win 10 X64

: ScreenShot016.jpg (134.47 KiB) Viewed 4950 times

Dylantje

Dear develop... Strange thing Try to flash my xxx boards... I see there is a new flash dev 8 2.0 Flash this on nodemcu very simple Works great nice ne features... Did buy 4 new Sonoff single board So i think flash them all 2 the same time. Only strange thing al the nodemcu working great... All the s...

Dylantje

Did swap... [ not with my wife :-( ] No luck.. To get it straight: "No luck" says it's the same circuit with another sensor going crazy? The most strange thing. I did a test setup.. Works for weeks... [ in my garage ] After a hard reset because i set something wrong.. This strange thing i...

Dylantje

Then you're using another sensor then me :) possibly the "mini" sensors .. i never tested them. Amyways... is it possible to swap the two sensors to see if the seonsor or the linknode causes the problem? Regards Shardan Did swap... [ not with my wife :-( ] No luck.. The most strange thing...

Dylantje

Shardan wrote: ↑23 May 2017, 16:42 hm...
may a stupid question... some of these PIR boards have a jumper that changes the way it Switches.
Both set same, if so? Sensivity setting of the sensor equal?

Regards
Shardan

no jumper on the same boards, i use the + and - for the sensors.
No settings possible bij the sensors.

Dylantje

mmm Hope you can help.... 2 the same linknode 8 relais boards. the same motion the same firmware. the same complete setup. [ hardware settings/ untick ttl etc etc ] use gpio 1 for dht, like you learned me here :-) use gpio 3 for motion... :-) Stange thing. 1 board works perfect. the other board [ ev...

Dylantje

Try to use the esp easy script to do the flash...

What happend then?

Dylantje

Thnaks

I did a hard reset
tx and rx connect when i bood.
Backup back and running like a new ..

thanks for the support//

Dylantje

mmm
Other problem...
Set my board in a reboot loop. witouth options? see no webgui, board is starting en
Was playing with the settings...

Is there a way i can return to factory or ... other options. to place a backup back..?

Thanks again!

xxx

Dylantje

That should be very great...
Without the xiaomi bridge out of the box working Xiaomi sensors should be a very nice feature...
I think stuntteam has 1 of the xiaomi sensors .... [ my gift ]

Dylantje

mmm 5 volt....
Do i need a power up system...??
Output is 3,3v...from this board

Dylantje

Hello Dylantje, put a resistor of 10K-Ohm from +3,3V to the Data Out / GPIO-Pin you use for PIR. Regards Shardan Dear Sharan... I did try that only no luck @ all. Did try 4 types motions sensors... And i use different Gpio... No stable motion .... GPIO 0 and 16.. both work fine with a DHT. I try th...

Dylantje

Is this option available in the normal EspEasy flash?

Dylantje

Dear Shardan... Thanks for your explane..... Only this i higher math for me. :roll: I am just a bricklayer...... :lol: :lol: Still get no stable pir working. Everything i try give a on /off on/off motion sensor.. First i need to get 1 stable pir.... When i do have 1 stable i think i must be happy..

Dylantje

dear all, Someone have a pir working with a ESP breadboard? http://linksprite.com/wiki/index.php5?title=LinkNode_R8:_Arduino-compatible_WiFi_relay_controller Or can someone tell me how i must setup this option. The esprelaisboard have 3 pins: NC normaly closed COM NO normaly open So what port do nee...

Dylantje

Thanks

The hard reset was the option.
Replace a backup and everything is working oke...

Love

Dylantje

A problem... From this day the espboard is restarting in after 3 minutes... Did try a lot other setting.. No luck @all Is there a way to set back the factory of the ESP software? Cannot reach the board with the webgui anymore.. [ did something wrong in the hardware settings i think :-) ] Or need i t...

Dylantje

Dear all. Please make love not WAR... :D I'am very happy with this answers and this very cheap board... I do have have a other board to: https://www.youtube.com/watch?v=ZLgllGQ_X0I&t=487s Expensive, only not better.. :cry: I am a BOB the brick layer... so i am happy with all of the support.. :ro...

Dylantje

Thanks!!!
The uncheck the serial.
And the on gpio1 is working great!!!

1 thing..
When i power off and then power on..
There is 1 relay clicking on.. GPIO 10

when i use this board with lights, all the lights are off with power up.
Only GPIO 10 not..

Do you perhaps a solution for that?

xxx

Dylantje

@ Shardan.

THANKS!!!
This was what i need... the jumper i mist.....

Is there perhaps als a free gpio where i can put a DHT on?
Or perhaps the extra 9 switch...?
I mean is there a gpio on the board that is not in use for the 8 relais.
And where i can put on a other sensor

Thanks again!!

Dylantje

I can confirm that the Linknode R4 is working great with ESPEasy. I bought one a few days ago and immediately flashed it with ESPEasy (4096 flash size). To get started easily, i have posted which GPIO belongs to which relay and such here: https://gathering.tweakers.net/forum/list_message/49734053#4...

Dylantje

Dear all, I wil try to flash a sonoff dual. https://www.google.nl/search?q=sonoff+dual&espv=2&tbm=isch&tbo=u&source=univ&sa=X&ved=0ahUKEwiIlc-anPTSAhXEfhoKHbwYAzoQsAQIKg&biw=1745&bih=819 I did solder 4 pins on the upper left corner on the board. Try the flash tool and...

Dylantje

I did power off the esp..[ lot of work ]
Now it is functioning ok....

Only strange that a reboot is not the same as a power off...

Dylantje

Dear all, My esp is running in a place where i cannot simple reach him. Only a strange problem. a few days a go the esp stop sending his value to domoticz He works for a few months..:-( I can see the webui so i did reboot the esp, no change in the webui i see the value so the sensors are working. I ...

Dylantje

Dear all, From holland here..:-) What are the option here in Holland with the new Rflink 868Mhz module? https://www.nodo-shop.nl/nl/rflink-gateway/186-rflink-gateway-componenten.html Is it perhaps possible to build a 868Mhz on the same arduino like 4334Mhz? Run then with that arduino the 434 and the...

Dylantje

mm i do not understand how this is working..
Do i need to to flash the esp with espeasy?
And then use your plugin?
Or do i need your plugin with arduino ide and then flash?

Dylantje

Please tell me how.

Dylantje

sorry for my dombo question.
Only can i or can i not control a rgbw strip, with easpeasy?

Dylantje

mmm that sonof have nice devices...
Should this one work with Espeasy?
https://www.itead.cc/smart-home/motor-r ... witch.html

Dylantje

mmm

What are there for more options possible with this nano/arduino easy?

Or just because it is possible?

Dylantje

mm i did pay for some software.. I see only the standard webgui i think... Need some dirext http acces to th pins.. The sensor: https://www.google.nl/search?q=dht+sensor&espv=2&biw=1745&bih=864&tbm=isch&tbo=u&source=univ&sa=X&ved=0ahUKEwiP4L3pq6HRAhWTclAKHW3OBMAQsAQIR...

Dylantje

mmm I think ... why is there no place where someone tell me the AP adres............... Only i do have him on my network. Looks it is acthing very fast, that's ok... Pehaps a direct http link for all the relays? That is the only thing i need in Domoticz.. Or do i need to reflash with espeasy? And ho...

Dylantje

Do have the board @ hom..
See the wifi that's sensding
Connect with it...
only what is the standard ip for the setup page?

Dylantje

What is the best way to use the relayboard.
Switching the Live or the N?

Dylantje

What are the options wih this board?
Can espeasy see all sensors?

Dylantje

pppfffff. Guys.... This place is the best option ther eis to share.. Live free, only keep your ..... Lobe the Internet... Thanks for all the nice things i am happy with the options persons here give. Money is the worlds bad thing... Or perhaps..... We need it.... say THANKS to all.. Love. and not wa...

Search found 255 matches