Let's Control It

riker1

Hi

having subnet security set to :
Allowed IP Range 192.168.0.0 - 192.168.0.255

but can ping from 192.168.1.110

why?

Thanks

riker1

thanks
ok, could be the motor of the fridge, but this starts more often.

I have a resistors attached.

Maybe I need a stronger one?

riker1

Hi
haveing DS18b20 attached and device result requently vary

I experienced that once or twice a day the results vary

temp shows increased values but temp is not changing.

messure the fridge so temp is quite constanct.

Thanks for hints.

using firmware mega-20180507

riker1

Hi I did send commands like- It used to work. http://192.168.0.167/control?cmd=NeoPixelAll,0,0,0 Now all of a sudden, only one command isexecuted. no other. running v2.0-20180113 having neopixel with 60 led. A reboot does not solve it. in the log no hint. when I reconnect neopixel - power off, power...

riker1

perfect, thanks, it is working

riker1

Hi
how can I enable reboot allowed via http command.

Unknown or restricted command!

xxx./control?cmd=reboot

Thanks

riker1

I experienced a lot of wifi disconnects and connects. why is ESP often get disconnected and reconnecting? Have ~20-30 x ESP8266 modules running. Most with ESP Easy, and none disconnect/connect from either Wi-Fi nor MQTT. Maybe you should troubleshoot there first? Hi maybe it is related to device de...

riker1

TD-er wrote: ↑05 Jun 2018, 14:06
There is an event when wifi is connected and you could set a "LWT" (Last Will and Testament) in the MQTT config.
If the node is disconnected from the broker, the broker will send that LWT message.

where do i configure the LWT? in mqtt controller config? or mosquitto?

riker1

Hi
Have a route from 4.1 set
to 0.x
So could send a mail
Or mqtt

so if ESP is fallback to AP, with 192.168.4.1 it still can send emails, and mqtt via route.

I experienced a lot of wifi disconnects and connects.
why is ESP often get disconnected and reconnecting?

riker1

ok, sad

riker1

Hi
is notification further developed?

riker1

Hi
I experienced that the esp is not always able to connect to the Router

How can I define a rule to send a message/ or switch an GPIO do show if network connect - STA Mode is running?

Or send a mail, MQTT when esp is falling back to AP Mode

Thanks for the help.

Thomas

riker1

Same with mega-20180524 36946: EVENT: VCC162#VCC162=2.93 38977: SYS : 0.00 38979: EVENT: sysload#V_sysload=0.00 39016: ACT : gpio,0,0 39018: SW : GPIO 0 Set to 0 42002: SYS : 0.00 42004: EVENT: sysload#V_sysload=0.00 42039: ACT : gpio,0,0 42041: SW : GPIO 0 Set to 0 9081: SYS : 0.00 9083: EVENT: upt...

riker1

Hi I have running firmware Firmware Build 20102 - Mega Libraries ESP82xx Core 2_4_1, NONOS SDK 2.2.1(cfd48f3), LWIP: 2.0.3 GIT version mega-20180516 Plugins 71 [Normal] [Testing] Build Md5 817d5ee7ca5a6e56435cdd1d9ae97db Md5 check passed. Build time May 16 2018 02:14:05 Binary filename ESP_Easy_mega...

riker1

Hi
still not supported?

riker1

jonathan-orsel wrote: ↑02 May 2018, 05:27 Hello,
I made some updates on your plugin for my own usage :
> Led count and column count in plugin configuration (need a restart to apply)

Hi
is this integrated in a special firmware?
Thanks T

riker1

Hi

I tried to run command NeoPixelAll.

But it is not working

any restrictions with firmware?

dev, test, normal?

Thanks thomas

riker1

Hi I think it is hardware related. Having this behaviour only on the lolin3 nodemcu V3 update same on Wemos mini 23981: Ram usage: Webserver only: 0 including Core: 0 flashStringCalls: 20 flashStringData: 17315 25721: Ram usage: Webserver only: 0 including Core: 0 flashStringCalls: 35 flashStringDat...

riker1

Hi I deployed config.dat to another esp same behaviour. load rises fast to 100% on the test esp , earlier config was running nice with no load increase as recognised on the other see serial log 537083 : SYS : 100.00 537085 : EVENT: sysload#V_sysload=100.00 539109 : SYS : 100.00 539111 : EVENT: syslo...

riker1

Hi

incorrect error message.

uploading a wrong file - not named config.dat

still gets the response: upload ok.

riker1

can not upload config.dat info forum

Hi

is this a know restriction?
saying invalid format config.dat

riker1

Hi please see behaviour: logging via mqtt to fhem devices disbaled except sstinfo load. 2018-05-19_10:07:04 mqtt_DEV_esp155_KTM Connected 2018-05-19_10:07:04 mqtt_DEV_esp155_KTM sysload: 0.0 2018-05-19_10:08:00 mqtt_DEV_esp155_KTM sysload: 22.0 2018-05-19_10:08:30 mqtt_DEV_esp155_KTM sysload: 40.0 2...

riker1

ok understood, thanks

can it alse be used to monitor power supply from adapter?

I eperienced sometimes VCC is shown as -1

riker1

Hi T-D

thanks for the info

but I do not understand why different esp8266 behave different, same version of firmware deployed.

your statement sounds like a general topic

riker1

Hi
what exactly is the function of the vcc versions of the firmware?

riker1

Hi having a lolin nodemcu running with mega-20180409 even after rebooting, load rises to 100% . There is only one PIR device connected. One simple rule in place two controller - fhem and mqtt free Mem: 13568 (8792 - addLog) How can I identify where the load used ? can it be a power problem? Log is n...

riker1

It may be possible, but in my experience the performance of both AP and STA on the ESP8266 is just horrible. ESP32 does feel a lot quicker when AP and STA mode are active. My suggestion would be to look at the ESP32 for such. Don't forget to set the packet forwarding, e.g. "router" mode. ...

riker1

TD-er wrote: ↑05 May 2018, 00:12 How do you upload the firmware?
Via Web-upload?
Please try using the serial upload.

ok, thanks
working via serial

but only for older versions....
running now: v2.0.0-dev13

but I can not open the website for config 192.168.4.1 with versions like mega-28160507,

riker1

Yes webupload. Ok will check serial

riker1

Hi
can I use STA and AP mode in parallel and define my own subnet?

Want to create a guest subnet.

Not sure if this is possible?

Thanks

riker1

Hi I tried to upload firmware to the robotdyn d1r2 - 32mb flash. error Update: ESP_Easy_mega-20180409_normal_ESP8266_4096.bin ERROR[4]: Not Enough Space There should be enough space. INIT : Booting version: (custom) INIT : Warm boot #4 FS : Mounting... FS : Mount successful, used 75802 bytes of 1132...

riker1

Hi having a generic device systeminfo with sysload. checking versus Main tab and sysload displayed there , device with sysinfo is not showing the same information what could cause the problem. Background: sysload is increasing and then esp is becoming very slow. Implemented a rule to reboot if syslo...

riker1

ok, thanks
will try

riker1

Hi Edautz,

thanks.

A: Used a 47uF and 102pF power decompling consensator soldered over the pir power connections at the ESP8266 side.
which pins did you use? I am not an expert so?

Thanks Thomas

riker1

---- I solved this with the next solutions: A: Used a 47uF and 102pF power decompling consensator soldered over the pir power connections at the ESP8266 side. B: Put the ESP in 802.11G mode instead of 802.11N mode. I think the Rf spectrum will be less in G mode. C: Put the ESP in wifi STA mode only...

riker1

solved it.

looks like it was caused by some blanks in the ruleset.!!!!!

Thanks for helping

riker1

Hi also tried now using state with threshold. values are correct, but rule still not executed.... is it maybe a problem upper lower letters? HTTP : closing connection SR04 : State 1 EVENT: Dist_139#Dist_V=1.00 RuleDebug Processing:rules1.txt flags CMI parse output: RuleDebug: 100: dist_139#dist_v=1....

riker1

did switch on debug serial and see more but only RuleDebug: 100: dist_139#dist_v<100.00 do RuleDebug: 101: gpio,16,0 but does not show execution of gpio command. EVENT: Dist_139#Dist_V=125.34 Processing time:47 milliSeconds HTTP : connecting to 192.168.0.9:8383 HTTP : closing connection SR04 : Dista...

riker1

What if you leave out the condition in the on statement? And what firmware do you use? Rules are not easily tested indeed, you might change the loglevel to see if it shows more info. Hi do you mean : on Dist_139#Dist_V do GPIO,16,0 endon led 16 not triggered. log does not say anything about GPIO co...

riker1

thanks for checking, of course I have values lower than 100 still rule not triggered. any way to check if a rule is tiggered/passed? - debugging ? rule and execution should show up in log, right? like : EVENT: Dist_139#Dist_V=6.03 4665343 : SR04 : Distance: 7.76 4665344 : EVENT: Dist_139#Dist_V=7.76...

riker1

Hi I am having an distance sensor SR04 attached. in log I see: 2 entries. I do not understand the EVENT, but how can I control the SR04 entry? how can I control / customize it? 944019 : EVENT: Dist_139#Dist_V=125.97 945199 : SR04 : Distance: 125.09 945200 : EVENT: Dist_139#Dist_V=125.09 946199 : SR0...

riker1

no hints?

riker1

Hi
did you ever had a problem with wrong readings?
I have often shorter readings in distance ......

thanks

riker1

i wonder if this is why i get whacky readings (distance in millions of cm) when there's nothing in range. sure sounds like it... i might have to try the resistor trick Hi see also here: there is an update on the way https://www.letscontrolit.com/forum/viewtopic.php?p=27241#p27241 I think it is for ...

riker1

Hi i do have often false readings for the sr04 found this: http://therandomlab.blogspot.de/2015/05/repair-and-solve-faulty-hc-sr04.html especially this: http://therandomlab.blogspot.de/2015/05/repair-and-solve-faulty-hc-sr04.html?showComment=1476201584407#c443883765476979154 anyone knowing if the pl...

riker1

Hi having a distance sensor attached. in the log I do see What is creating the entry : sr04? can I avoid it? Will this be send to a controller? Thanks T 19 : EVENT: Dist_139#Dist_V=123.78 164970512 : SR04 : Distance: 124.22 164970513 : EVENT: Dist_139#Dist_V=124.22 164971512 : SR04 : Distance: 123.7...

riker1

Hi

strangewise I am having a constant disconnects.

IFI : Disconnected! Reason: 'Auth expire' Connected for 2247 ms

wifi is ok. do not know where auth is expering?

Thanks for the hints.

t

riker1

On the wiki there is already a very simple level converter documented for these sensors. You can simply use some resistors. Thanks for guiding me to the WIKI, did it as described there. Just wondering if it is working without the level converter as I did see in some internet tutorials. want to avoi...

riker1

Hi having a distance sensor attached log is saying: 0843707 : EVENT: Dist_139#Dist_V=152.64 10844706 : SR04 : Distance: 151.78 10844707 : EVENT: Dist_139#Dist_V=151.78 device is defined: with value, also tried state. but as well no trigger rule for event: on Dist_139#Dist_V<100.00 do GPIO,14,1 endon...

riker1

Hi
via google it is possible to find a lot if tutorials
connecting SR04 straight to the esp8266.

not via level converter.

Any experience with that ?

some even just use 3,7 V input? it is supposed to have 5 i think

Thanks

Search found 344 matches