Warema 8k hand transmitter

Post here about devices that are not yet or not fully supported

Moderators: rtenklooster, Voyager, BertB, Stuntteam

Post Reply
Message
Author
dproetel
Normal user
Posts: 6
Joined: 02 Feb 2017, 21:06

Warema 8k hand transmitter

#1 Post by dproetel » 02 Feb 2017, 21:13

good afternoon,
I try to connect a warema sender with 8 channels. Under device it shows:
rflinki 00006CA7 0 oben 6 Light/Switch Warema Open
but it seems that all 8 channels have the same entry. Any hints?

thanks in advance Daniel

User avatar
Stuntteam
Site Beheer
Posts: 648
Joined: 27 Jan 2016, 16:46

Re: Warema 8k hand transmitter

#2 Post by Stuntteam » 03 Feb 2017, 00:49

Check your email..
-=# RFLink Gateway Development Team #=-
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8

kafe75
Normal user
Posts: 1
Joined: 11 Feb 2017, 10:05

Re: Warema 8k hand transmitter

#3 Post by kafe75 » 11 Feb 2017, 10:12

good morning,

i´ve got the same problem with my 8k hand transmitter, controlling my roller shutters.

In domoticz the control command is recognized as warema protocol, but it´s always the same address.

Do i have to pair the devices with my master control unit?

User avatar
Stuntteam
Site Beheer
Posts: 648
Joined: 27 Jan 2016, 16:46

Re: Warema 8k hand transmitter

#4 Post by Stuntteam » 11 Feb 2017, 10:51

Check your email..
-=# RFLink Gateway Development Team #=-
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8

Des0re
Normal user
Posts: 1
Joined: 10 Aug 2019, 20:31

Re: Warema 8k hand transmitter

#5 Post by Des0re » 21 Aug 2019, 18:07

I also have a problem with warema EWFS
Rflink recognises the switches. But i cannot control with rflink.

tkospace
Normal user
Posts: 1
Joined: 09 Jun 2020, 23:26

Re: Warema 8k hand transmitter

#6 Post by tkospace » 09 Jun 2020, 23:28

Stuntteam wrote:
11 Feb 2017, 10:51
Check your email..
Hello,

I have the same problem.
Could you send me the information too?

Br,
tkospace

intelligenzbestie
Normal user
Posts: 1
Joined: 23 Jun 2020, 21:08

Re: Warema 8k hand transmitter

#7 Post by intelligenzbestie » 23 Jun 2020, 21:16

Hello,

I would be interested as well.
I have a Warema EWFS Weather Station Plus combined with an adapter to control an even older Warema awning.
I also have a handheld transmitter to manually move it out and in.
I managed to retrieve the commands for out and in using a Signalduino at 433 MHz and I can "replicate" them as raw messages so this works.
But I would be intested in the data of the weather station because it contains a wind and rain sensor.
And I would like to "see" when the weather station "commands" the awning to move out or in.

Thanks,
best regards
Richard

User avatar
Stuntteam
Site Beheer
Posts: 648
Joined: 27 Jan 2016, 16:46

Re: Warema 8k hand transmitter

#8 Post by Stuntteam » 24 Jun 2020, 00:05

For new/unknown devices follow the instructions here: http://www.rflink.nl/blog2/development
-=# RFLink Gateway Development Team #=-
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8

Post Reply

Who is online

Users browsing this forum: No registered users and 6 guests