Falmec Support

Post here about devices that are not yet or not fully supported

Moderators: rtenklooster, Voyager, BertB, Stuntteam

Post Reply
Message
Author
shira66@gmx.at
Normal user
Posts: 3
Joined: 24 Sep 2020, 15:15

Falmec Support

#1 Post by shira66@gmx.at » 24 Sep 2020, 15:19

The Falmec hood is listed as supported device for R 48, but it seems not to work. Any suggestions.
Regards

User avatar
Stuntteam
Site Beheer
Posts: 658
Joined: 27 Jan 2016, 16:46

Re: Falmec Support

#2 Post by Stuntteam » 24 Sep 2020, 16:36

http://www.rflink.nl/blog2/development
Make a debug log and mail it..
-=# RFLink Gateway Development Team #=-
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8

shira66@gmx.at
Normal user
Posts: 3
Joined: 24 Sep 2020, 15:15

Re: Falmec Support

#3 Post by shira66@gmx.at » 24 Sep 2020, 16:42

20;4F;DEBUG;Pulses=34;Pulses(uSec)=300,270,600,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,270,600,600,240,600,240,6990;
20;50;DEBUG;Pulses=34;Pulses(uSec)=270,270,600,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,270,570,600,240,600,240,6990;
20;51;DEBUG;Pulses=34;Pulses(uSec)=300,270,600,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,270,600,600,240,600,240,6990;
20;52;DEBUG;Pulses=34;Pulses(uSec)=330,240,600,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,240,600,600,240,600,240,6990;
20;53;DEBUG;Pulses=34;Pulses(uSec)=330,240,600,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,240,600,600,240,600,240,6990;
20;54;DEBUG;Pulses=34;Pulses(uSec)=330,270,600,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,240,600,600,240,600,240,6990;
20;55;DEBUG;Pulses=34;Pulses(uSec)=330,270,600,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,600,240,270,600,600,240,600,240,6990;

That was pressing the 'down' on the remote

Post Reply

Who is online

Users browsing this forum: No registered users and 10 guests