Warema 8k hand transmitter
Moderators: rtenklooster, Voyager, BertB, Stuntteam
Warema 8k hand transmitter
good afternoon,
I try to connect a warema sender with 8 channels. Under device it shows:
rflinki 00006CA7 0 oben 6 Light/Switch Warema Open
but it seems that all 8 channels have the same entry. Any hints?
thanks in advance Daniel
I try to connect a warema sender with 8 channels. Under device it shows:
rflinki 00006CA7 0 oben 6 Light/Switch Warema Open
but it seems that all 8 channels have the same entry. Any hints?
thanks in advance Daniel
Re: Warema 8k hand transmitter
Check your email..
-=# RFLink Gateway Development Team #=-
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8
Re: Warema 8k hand transmitter
good morning,
i´ve got the same problem with my 8k hand transmitter, controlling my roller shutters.
In domoticz the control command is recognized as warema protocol, but it´s always the same address.
Do i have to pair the devices with my master control unit?
i´ve got the same problem with my 8k hand transmitter, controlling my roller shutters.
In domoticz the control command is recognized as warema protocol, but it´s always the same address.
Do i have to pair the devices with my master control unit?
Re: Warema 8k hand transmitter
Check your email..
-=# RFLink Gateway Development Team #=-
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8
Re: Warema 8k hand transmitter
I also have a problem with warema EWFS
Rflink recognises the switches. But i cannot control with rflink.
Rflink recognises the switches. But i cannot control with rflink.
-
- New user
- Posts: 1
- Joined: 23 Jun 2020, 21:08
Re: Warema 8k hand transmitter
Hello,
I would be interested as well.
I have a Warema EWFS Weather Station Plus combined with an adapter to control an even older Warema awning.
I also have a handheld transmitter to manually move it out and in.
I managed to retrieve the commands for out and in using a Signalduino at 433 MHz and I can "replicate" them as raw messages so this works.
But I would be intested in the data of the weather station because it contains a wind and rain sensor.
And I would like to "see" when the weather station "commands" the awning to move out or in.
Thanks,
best regards
Richard
I would be interested as well.
I have a Warema EWFS Weather Station Plus combined with an adapter to control an even older Warema awning.
I also have a handheld transmitter to manually move it out and in.
I managed to retrieve the commands for out and in using a Signalduino at 433 MHz and I can "replicate" them as raw messages so this works.
But I would be intested in the data of the weather station because it contains a wind and rain sensor.
And I would like to "see" when the weather station "commands" the awning to move out or in.
Thanks,
best regards
Richard
Re: Warema 8k hand transmitter
For new/unknown devices follow the instructions here: http://www.rflink.nl/blog2/development
-=# RFLink Gateway Development Team #=-
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8
Who is online
Users browsing this forum: No registered users and 49 guests