WT32-ETH01

[Rub87]

How can i attempt to resolve that?

[TD-er]

Not sure, I have to look into the code for this.

[Rub87]

Code: Select all

217 : Info   : Connect to:
217 : Info   : Ethernet
218 : Info   : Eth Wifi mode: Ethernet ETH: PHY Typee: LAN8710 PHYAddr: 0 Eth Clock mode: External crystal oscillator MDC Pin: 16 MIO Pin: 17 Power Pin: -1
222 : Info   : ETH Started
4223 : Info   : ETH Connected
4224 : Info   : firstLoopConnectionsEstablished
7230 : Info   : ETH MAC: A4:CF:12:64:B3:8F IPv4: 10.0.1.44 (ESP-Easy) GW: 10.0.1.1 SN: 255.255.255.0 FULL_DUPLEX 100Mbps

seems the clock mode has to be set to External osc...

[TD-er]

Ah, so it does have its own crystal oscillator?
Yep, then you should set it to have one external

[Rub87]

Yep. Just spotted it also..


The new lan8720 i put on has quite different look then old one. It is more round off whereas the old was very edgy, alot like these bga memory chips. Wasnt easy to get it on with a paint removal gun

[TD-er]

Wow, you removed it using a paint removal gun?

The LAN8710A does have 32 pads, while the LAN8720A has only 24 (25 if you count the GND at the bottom)
Difference between both is that the LAN8720A only supports RMII and no longer the older 4 wire version.
But since we only use that one, it doesn't matter to us.

[Rub87]

Weapon of choice

[TD-er]

Well I don't think I can do that with such a blower myself, so respect

[Rub87]

Now could you aybe add the setting for the wESP32 in the code so there will also be a .bin which has directly the correct settings inside for other users that maybe also like the wESP32? despte its higher price its pretty well made thing with proper PoE power identification and galvnic isolation etc.

[TD-er]

Please show me the settings you now use and I will add them.

[Rub87]

Code: Select all

 Eth Wifi mode: Ethernet ETH: PHY Typee: LAN8710 PHYAddr: 0 Eth Clock mode: External crystal oscillator MDC Pin: 16 MIO Pin: 17 Power Pin: -1  

[Smotek7]

Hi,
is in the current release for ESP32 .bin which one can flasch to WT32-ETH1?
Or I need to create my own for WT32.

[TD-er]

You can flash any esp32 eth build as long as your board uses LAN8710A or LAN8720A (or the tk<somewhat> board which I forgot the name)

Only thing is, you may need to configure the eth yourself by hand as we don't have a predefined "factory default" setting for it yet.

[Smotek7]

Everything works.
To summarize:
Board WT32-ETH01
USB to RS232 converter
IO0 to GND
Flash: ESP_Easy_mega_20210114_normal_ESP32_4M316k_ETH-factory.bin
Connect to wifi and setting lan.

lan set.JPG (53.86 KiB) Viewed 1567 times

Disconnect IO0
Restart and the module will connect to the lan.

[enesbcs]

Flash: ESP_Easy_mega_20210114_normal_ESP32_4M316k_ETH-factory.bin
Connect to wifi and setting lan.
lan set.JPG

Yes, i can confirm.
viewtopic.php?p=49536#p49536

[iron]

@TD-er perhaps it is safe to assume it is time to set a predefined setting for this ?

[hamster]

I created a nice enclosure for the WT32-ETH01 + Relays
see thingiverse.. https://www.thingiverse.com/thing:4750234

[TD-er]

@TD-er perhaps it is safe to assume it is time to set a predefined setting for this ?

Yep.
Can you make an issue on Github for it, as these things on the forum as next to impossible to find back later when I'm at a computer I can actually code and compile on and the forum doesn't have a mark unread....

[TD-er]

I created a nice enclosure for the WT32-ETH01 + Relays
see thingiverse.. https://www.thingiverse.com/thing:4750234

Nice enclosure!