It does not solve the problem. What I did:
1. flash and erase with 4Mb blank bin file. Disconnect and wait 5 min. Read that somewhere as a possible solution
2. flash with your latest build. Disconnect and wait 5 min.
3.(@20976) boot, and tried to connect my iPad with AP ESP-Easy. Didn't wanted to connect ;-(
4. entered in Terminal debug 4
5. (@91579) connect my MacBook with the AP ESP-Easy.
6. open browser, open 192.168.4.1/advanced, and disable periodical WiFi scan.
7. (@147442) configured NTP and "Submit"
8. changed to 192.168.4.1/setup, and selected my best AP, and entered Wifi-Key
9. no connection, tried again.
10. (@328794) changed to 192/168.4.1/config. checked SSID and entered again my Wifi-key.
11. (@349488)After still no connection, hit in 192.168.4.1/tools the REBOOT -button
12.waited till (@46349)
Code: Select all
Free RAM:32184
284 : Info : INIT : Cold Boot - Restart Reason: External System
286 : Info : FS : Mounting…
6482 : Info : FS : Mount successful, used 0 bytes of 957314
RESET: Resetting factory defaults… using default settings
RESET: Warm boot, reset count: 0
RESET: formatting…
RESET: formatting done…
15681 : Info : SaveToFile: free stack: 3504
15740 : Info : FILE : Saved config.dat offset: 28672 size: 820
15741 : Info : SaveToFile: free stack after: 3504
15742 : Info : SaveToFile: free stack: 3568
15812 : Info : FILE : Saved config.dat offset: 0 size: 1296
15813 : Info : SaveToFile: free stack after: 3568
15814 : Info : SaveToFile: free stack: 3408
15847 : Info : FILE : Saved security.dat offset: 0 size: 593
15847 : Info : SaveToFile: free stack after: 3408
15850 : Info : SaveToFile: free stack: 3072
15860 : Info : FILE : Saved security.dat offset: 1024 size: 128
15860 : Info : SaveToFile: free stack after: 3072
RESET: Successful, rebooting. (you might need to press the reset button if you’ve just flashed the firmware)
ets Jan 8 2013,rst cause:2, boot mode:(3,7)
load 0x4010f000, len 3584, room 16
tail 0
chksum 0xb0
csum 0xb0
v2843a5ac
~ld
ªU75 : Info :
INIT : Booting version: ‘bugfix/wifi_not_reconnect_56c4ca1’ (ESP82xx Core 2843a5ac, NONOS SDK 2.2.2-dev(38a443e), LWIP: 2.1.2 PUYA support)
76 : Info : INIT : Free RAM:32184
77 : Info : INIT : Soft Reboot #1 Last Action before Reboot: Intended Reboot: ResetFactory Last systime: 16 - Restart Reason: Software/System restart
79 : Info : FS : Mounting…
104 : Info : FS : Mount successful, used 75802 bytes of 957314
124 : Info : CRC : SecuritySettings CRC …OK
128 : Info : WiFi : Start network scan all channels
2318 : Info : WiFi : Scan finished, found: 8
2321 : Info : WiFi : Start network scan all channels
2430 : Info : INIT : Free RAM:27576
2431 : Info : INIT : I2C
2431 : Info : INIT : SPI not enabled
2532 : Info : INFO : Plugins: 47 [Normal] (ESP82xx Core 2843a5ac, NONOS SDK 2.2.2-dev(38a443e), LWIP: 2.1.2 PUYA support)
2538 : Info : Webserver: start
2539 : Info : Time set to 16.000 Time adjusted by 13462.00 msec. Wander: 3.74 msec/second
2541 : Info : Current Time Zone: STD time start: 1970-10-25 03:00:00 offset: 0 min
2543 : Info : Local time: 1970-01-01 00:00:16
3888 : Info : WD : Uptime 0 ConnectFailures 0 FreeMem 20448 WiFiStatus WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
4584 : Info : WiFi : Scan finished, found: 5
4587 : Error : WIFI : No valid wifi settings
4588 : Info : WIFI : Set WiFi to AP+STA
5626 : Info : WIFI : AP Mode ssid will be ESP-Easy with address 192.168.4.1
20976 : Info : AP Mode: Client connected: EE:F2:52:C5:27:92 Connected devices: 1
33889 : Info : WD : Uptime 1 ConnectFailures 0 FreeMem 17080 WiFiStatus WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
deb63886 : Info : WD : Uptime 1 ConnectFailures 0 FreeMem 17000 WiFiStatus WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
ug 4
>debug 4
Ok
add 2
aid 2
station: 3c:22:fb:0f:a1:70 join, AID = 2
91579 : Info : AP Mode: Client connected: 3C:22:FB:0F:A1:70 Connected devices: 2
93887 : Info : WD : Uptime 2 ConnectFailures 0 FreeMem 15920 WiFiStatus WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
station: ee:f2:52:c5:27:92 leave, AID = 1
rm 1
94763 : Info : AP Mode: Client disconnected: EE:F2:52:C5:27:92 Connected devices: 1
94776 : Debug : LoopStats: shortestLoop: 10308 longestLoop: 1053884 avgLoopDuration: 10874.39 loopCounterMax: 2910 loopCounterLast: 2756
94777 : Debug : Scheduler stats: (called/tasks/max_length/idle%) 8381/5569/6/31.89
123880 : Info : WD : Uptime 2 ConnectFailures 0 FreeMem 14720 WiFiStatus WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
128650 : Debug : LoopStats: shortestLoop: 10308 longestLoop: 4298567 avgLoopDuration: 15081.51 loopCounterMax: 2910 loopCounterLast: 2244
128651 : Debug : Scheduler stats: (called/tasks/max_length/idle%) 2241/1500/6/23.42
147442 : Info : Webserver args: 0: ‘usentp’ length: 2 1: ‘ntphost’ length: 13 2: ‘dststartweek’ length: 1 3: ‘dststartdow’ length: 1 4: ‘dststartmonth’ length: 1 5: ‘dststarthour’ length: 1 6: ‘dstendweek’ length: 1 7: ‘dstenddow’ length: 1 8: ‘dstendmonth’ length: 2 9: ‘dstendhour’ length: 1 10: ‘timezone’ length: 1 11: ‘latitude’ length: 8 12: ‘longitude’ length: 8 13: ‘syslogip’ length: 0 14: ‘syslogport’ length: 3 15: ‘syslog_log_level’ length: 1 16: ‘syslogfacility’ length: 1 17: ‘serial_log_level’ length: 1 18: ‘web_log_level’ length: 1 19: ‘useserial’ length: 2 20: ‘baudrate’ length: 6 21: ‘udpport’ length: 1 22: ‘webport’ length: 2 23: ‘ip’ length: 1 24: ‘wdi2caddress’ length: 1 25: ‘wireclockstretchlimit’ length: 1 26: ‘connection_failure_threshold’ length: 1 27: ‘max_wifi_tx_power’ length: 5 28: ‘wifi_sensitivity_margin’ length: 1 29: ‘extra_wifi_scan_loops’ length: 1 30: ‘edit’ length: 1 31: ‘plain’ length: 494
147449 : Info : SaveToFile: free stack: 3456
147525 : Info : FILE : Saved config.dat offset: 0 size: 1296
147526 : Info : SaveToFile: free stack after: 3456
147528 : Info : SaveToFile: free stack: 2960
147538 : Info : FILE : Saved security.dat offset: 1024 size: 128
147540 : Info : SaveToFile: free stack after: 2960
147542 : Debug : WiFi : Set TX power to 0dBm sensitivity: -69dBm
153889 : Info : WD : Uptime 3 ConnectFailures 0 FreeMem 13656 WiFiStatus WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
154772 : Debug : LoopStats: shortestLoop: 10308 longestLoop: 4298567 avgLoopDuration: 11209.75 loopCounterMax: 2910 loopCounterLast: 2328
154773 : Debug : Scheduler stats: (called/tasks/max_length/idle%) 2327/1549/6/33.26
159743 : Info : WiFi : Start network scan all channelsscandone
161930 : Info : WiFi : Scan finished, found: 7
161932 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:39:CE:ED Ch:3 (-70dBm) WPA2/PSK
161933 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:13:49:8D Ch:1 (-72dBm) WPA2/PSK
161934 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:39:C3:A3 Ch:6 (-77dBm) WPA2/PSK
161935 : Debug : WiFi : Scan result: Broom 18:83:BF:BC:75:8A Ch:8 (-91dBm) WPA2/PSK
161936 : Debug : WiFi : Scan result: #Hidden# 36:23:03:13:49:8D Ch:1 (-71dBm) WPA2/PSK
161938 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-62dBm) WPA2/PSK
161939 : Debug : WiFi : Scan result: #Hidden# 36:23:03:39:C4:5C Ch:10 (-59dBm) WPA2/PSK
183881 : Info : WD : Uptime 3 ConnectFailures 0 FreeMem 15048 WiFiStatus WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
184776 : Debug : LoopStats: shortestLoop: 10308 longestLoop: 4298567 avgLoopDuration: 12887.13 loopCounterMax: 2910 loopCounterLast: 2326
184777 : Debug : Scheduler stats: (called/tasks/max_length/idle%) 2325/1541/6/27.11
185362 : Info : SaveToFile: free stack: 3456
185431 : Info : FILE : Saved config.dat offset: 0 size: 1296
185432 : Info : SaveToFile: free stack after: 3456
185433 : Info : SaveToFile: free stack: 3296
185466 : Info : FILE : Saved security.dat offset: 0 size: 593
185467 : Info : SaveToFile: free stack after: 3296
185469 : Info : SaveToFile: free stack: 2960
185479 : Info : FILE : Saved security.dat offset: 1024 size: 128
185480 : Info : SaveToFile: free stack after: 2960
185482 : Info : WIFI : Credentials Changed, retry connection. SSID: Linksys Velop WHW03 V2
185484 : Info : WiFi : Best AP candscandone
switch to channel 10
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 3
cnt
connected with Linksys Velop WHW03 V2, channel 10
dhcp client start…
idate: Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-62dBm) WPA2/PSK
185486 : Info : WIFI : Connecting Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-62dBm) WPA2/PSK attempt #0
185489 : Debug : WiFi : Set TX power to 13dBm sensitivity: -69dBm RSSI: -62dBm
185493 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: DISCONNECTED
190682 : Debug : WIFI : Entering processConnect()
ip:10.187.1.143,mask:255.255.255.0,gw:10.187.1.254
190684 : Info : WIFI : Connected! AP: Linksys Velop WHW03 V2 (30:23:03:39:C4:5C) Ch: 10 Duration: 3232 ms
190685 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: Conn.
190721 : Debug : WIFI : Entering processGotIP()
190723 : Info : WIFI : DHCP IP: 10.187.1.143 (ESP-Easy) GW: 10.187.1.254 SN: 255.255.255.0 duration: 2000 ms
190736 : Info : SaveToFile: free stack: 3216
190747 : Info : FILE : Saved security.dat offset: 1024 size: 128
190748 : Info : SaveToFile: free stack after: 3216
190751 : Info : WIFI : Arduino wifi status: WL_CONNECTED 3 ESPeasy internal wifi status: Conn. IP
190752 : Debug : WiFi : WiFi services initialized
190754 : Info : firstLoopConnectionsEstablished
190770 : Debug More : NTP : NTP host ntp.xs4all.nl (194.109.6.2) queried
190793 : Info : NTP : NTP replied: delay 21 mSec Accuracy increased by 0.329 seconds
190795 : Info : Time set to 1623697347.329
190797 : Info : Current Time Zone: STD time start: 2021-10-31 03:00:00 offset: 0 min
190800 : Info : Local time: 2021-06-14 19:02:27
bcn_timout,ap_probe_send_start
ap_probe_send over, rest wifi status to disassoc
state: 5 -> 0 (1)
rm 0
199058 : Debug : WIFI : Entering processDisconnect()
199160 : Info : WIFI : Disconnected! Reason: ‘(200) Beacon timeout’ Connected for 10 s
199160 : Info : WIFI : Arduino wifi status: WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
199161 : Debug : WIFI : Disconnected: WiFi.status() = DISCONNECTED RSSI: 31 status: STATION_IDLE
213894 : Info : WD : Uptime 4 ConnectFailures 0 FreeMem 14536 WiFiStatus WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
214786 : Debug : LoopStats: shortestLoop: 729 longestLoop: 5402515 avgLoopDuration: 2546.01 loopCounterMax: 41152 loopCounterLast: 11748
214787 : Debug : Scheduler stats: (called/tasks/max_length/idle%) 11747/1558/6/41.27
216313 : Info : WiFi : Start network scan all channelsscandone
218499 : Info : WiFi : Scan finished, found: 8
218501 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:13:49:8D Ch:1 (-71dBm) WPA2/PSK
218502 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:39:CE:ED Ch:3 (-70dBm) WPA2/PSK
218503 : Debug : WiFi : Scan result: #Hidden# 36:23:03:39:CE:ED Ch:3 (-70dBm) WPA2/PSK
218505 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-60dBm) WPA2/PSK
218506 : Debug : WiFi : Scan result: #Hidden# 36:23:03:39:C3:A3 Ch:6 (-77dBm) WPA2/PSK
218507 : Debug : WiFi : Scan result: Broom 18:83:BF:BC:75:8A Ch:8 (-90dBm) WPA2/PSK
218508 : Debug : WiFi : Scan result: #Hidden# 36:23:03:39:C4:5C Ch:10 (-58dBm) WPA2/PSK
218510 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:AE:5D:83 Ch:9 (-74dBm) WPA2/PSK
235245 : Info : SaveToFile: free stack: 3456
235342 : Info : FILE : Saved config.dat offset: 0 size: 1296
235343 : Info : SaveToFile: free stack after: 3456
235345 : Info : SaveToFile: free stack: 2960
235355 : Info : FILE : Saved security.dat offset: 1024 size: 128
235356 : Info : SaveToFile: free stack after: 2960
235358 : Debug : WiFi : Set TX power to 0dBm sensitivity: -69dBm
235359 : Info : WIFI : Credentials Changed, retry connection. SSID: Linksys Velop WHW03 V2
235362scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 3
cnt
connected with Linksys Velop WHW03 V2, channel 10
dhcp client start…
: Info : WiFi : Best AP candidate: Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-60dBm) WPA2/PSK
235363 : Info : WIFI : Connecting Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-60dBm) WPA2/PSK attempt #0
235366 : Debug : WiFi : Set TX power to 11dBm sensitivity: -69dBm RSSI: -60dBm
235370 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: DISCONNECTED
236450 : Debug : WIFI : Entering processConnect()
236452 : Info : WIFI : Connected! AP: Linksys Velop WHW03 V2 (30:23:03:39:C4:5C) Ch: 10 Duration: 1003 ms
236453 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: Conn.
ip:10.187.1.143,mask:255.255.255.0,gw:10.187.1.254
238408 : Debug : WIFI : Entering processGotIP()
238409 : Info : WIFI : DHCP IP: 10.187.1.143 (ESP-Easy) GW: 10.187.1.254 SN: 255.255.255.0 duration: 2032 ms
238421 : Info : WIFI : Arduino wifi status: WL_CONNECTED 3 ESPeasy internal wifi status: Conn. IP
238422 : Debug : WiFi : WiFi services initialized
238978 : Debug More : NTP : NTP host ntp.xs4all.nl (194.109.6.2) queried
239011 : Info : NTP : NTP replied: delay 30 mSec Accuracy increased by 0.551 seconds
239013 : Info : Time set to 1623697395.551 Time adjusted by 41.33 msec. Wander: 0.01 msec/second
239016 : Info : Local time: 2021-06-14 19:03:15
243880 : Info : WD : Uptime 4 ConnectFailures 0 FreeMem 14680 WiFiStatus WL_CONNECTED 3 ESPeasy internal wifi status: Conn. IP Init
244769 : Debug : LoopStats: shortestLoop: 717 longestLoop: 5402515 avgLoopDuration: 3126.42 loopCounterMax: 41841 loopCounterLast: 9567
244769 : Debug : Scheduler stats: (called/tasks/max_length/idle%) 9565/1646/6/52.54
bcn_timout,ap_probe_send_start
ap_probe_send over, rest wifi status to disassoc
state: 5 -> 0 (1)
rm 0
247494 : Debug : WIFI : Entering processDisconnect()
247595 : Info : WIFI : Disconnected! Reason: ‘(200) Beacon timeout’ Connected for 11 s
247596 : Info : WIFI : Arduino wifi status: WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
247597 : Debug : WIFI : Disconnected: WiFi.status() = DISCONNECTED RSSI: 31 status: STATION_IDLE
260752 : Info : WiFi : Start network scan all channelsscandone
262939 : Info : WiFi : Scan finished, found: 8
262940 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:13:49:8D Ch:1 (-70dBm) WPA2/PSK
262941 : Debug : WiFi : Scan result: #Hidden# 36:23:03:13:49:8D Ch:1 (-71dBm) WPA2/PSK
262943 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:39:CE:ED Ch:3 (-71dBm) WPA2/PSK
262944 : Debug : WiFi : Scan result: #Hidden# 36:23:03:39:CE:ED Ch:3 (-69dBm) WPA2/PSK
262945 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-58dBm) WPA2/PSK
262947 : Debug : WiFi : Scan result: #Hidden# 36:23:03:39:C3:A3 Ch:6 (-76dBm) WPA2/PSK
262948 : Debug : WiFi : Scan result: #Hidden# 36:23:03:39:C4:5C Ch:10 (-59dBm) WPA2/PSK
262949 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:AE:5D:83 Ch:9 (-75dBm) WPA2/PSK
262951 : Info : WiFi : Best AP candidate: Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-58dBm) WPA2/PSK
273887 : Info : WD : Uptime 5 ConnectFailures 0 FreeMem 15104 WiFiStatus WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
274775 : Debug : LoopStats: shortestLoop: 717 longestLoop: 5402515 avgLoopDuration: 5408.86 loopCounterMax: 41841 loopCounterLast: 5537
274776 : Debug : Scheduler stats: (called/tasks/max_length/idle%) 5536/1661/6/33.91
277796 : Info : SaveToFile: free stack: 3456
277866 : Info : FILE : Saved config.dat offset: 0 size: 1296
277867 : Info : SaveToFile: free stack after: 3456
277869 : Info : SaveToFile: free stack: 2960
277879 : Info : FILE : Saved security.dat offset: 1024 size: 128
277879 : Info : SaveToFile: free stack after: 2960
277881 : Debug : WiFi : Set TX power to 0dBm sensitivity: -69dBm
277882 : Info : WIFI : Credentials Changed, retry connection. SSID: Linksys Velop WHW03 V2
277885 :scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 3
cnt
Info : WiFi : Best AP candidate: Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-58dBm) WPA2/PSK
277887 : Info : WIFI : Connecting Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-58dBm) WPA2/PSK attempt #0
277889 : Debug : WiFi : Set TX power to 9dBm sensitivity: -69dBm RSSI: -58dBm
277894 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: DISCONNECTED
278922 : Debug : WIFI : Disconnected: WiFi.status() = DISCONNECTED RSSI: 31 status: STATION_CONNECTING
connected with Linksys Velop WHW03 V2, channel 10
dhcp client start…
279920 : Debug : WIFI : Entering processConnect()
279922 : Info : WIFI : Connected! AP: Linksys Velop WHW03 V2 (30:23:03:39:C4:5C) Ch: 10 Duration: 2032 ms
279922 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: Conn.
ip:10.187.1.143,mask:255.255.255.0,gw:10.187.1.254
279969 : Debug : WIFI : Entering processGotIP()
279971 : Info : WIFI : DHCP IP: 10.187.1.143 (ESP-Easy) GW: 10.187.1.254 SN: 255.255.255.0 duration: 46 ms
279982 : Info : WIFI : Arduino wifi status: WL_CONNECTED 3 ESPeasy internal wifi status: Conn. IP
279983 : Debug : WiFi : WiFi services initialized
280561 : Debug More : NTP : NTP host ntp.xs4all.nl (194.109.6.2) queried
280594 : Info : NTP : NTP replied: delay 30 mSec Accuracy increased by 0.134 seconds
280595 : Info : Time set to 1623697437.134 Time adjusted by 35.51 msec. Wander: 0.01 msec/second
280598 : Info : Local time: 2021-06-14 19:03:57
bcn_timout,ap_probe_send_start
ap_probe_send over, rest wifi status to disassoc
state: 5 -> 0 (1)
rm 0
288044 : Debug : WIFI : Entering processDisconnect()
288145 : Info : WIFI : Disconnected! Reason: ‘(200) Beacon timeout’ Connected for 8123 ms
288146 : Info : WIFI : Arduino wifi status: WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
288147 : Debug : WIFI : Disconnected: WiFi.status() = DISCONNECTED RSSI: 31 status: STATION_IDLE
288372 : Debug : HTML : Request file /wpad.dat
288400 : Debug : HTML : Request file /wpad.dat
301792 : Info : WiFi : Start network scan all channelsscandone
303979 : Info : WiFi : Scan finished, found: 6
303981 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-60dBm) WPA2/PSK
303982 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:39:CE:ED Ch:3 (-70dBm) WPA2/PSK
303983 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:39:C3:A3 Ch:6 (-77dBm) WPA2/PSK
303985 : Debug : WiFi : Scan result: #Hidden# 36:23:03:39:C4:5C Ch:10 (-61dBm) WPA2/PSK
303986 : Debug : WiFi : Scan result: Broom 18:83:BF:BC:75:8A Ch:8 (-94dBm) WPA2/PSK
303987 : Debug : WiFi : Scan result: #Hidden# 36:23:03:AE:5D:83 Ch:9 (-74dBm) WPA2/PSK
303989 : Info : WiFi : Best AP candidate: Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-60dBm) WPA2/PSK
304535 : Info : WD : Uptime 5 ConnectFailures 0 FreeMem 15232 WiFiStatus WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
304779 : Debug : LoopStats: shortestLoop: 705 longestLoop: 5402515 avgLoopDuration: 2593.50 loopCounterMax: 42553 loopCounterLast: 11531
304779 : Debug : Scheduler stats: (called/tasks/max_length/idle%) 11527/1640/6/50.34
308672 : Debug : HTML : Request file /index.htm.gz
308700 : Debug : HTML : Request file /index.htm
309680 : Debug : HTML : Request file /proxy-safebrowsing.googleapis.com:443
309681 : Debug : HTML : Request file /proxy-safebrowsing.googleapis.com:443
328794 : Info : Webserver args: 0: ‘name’ length: 8 1: ‘unit’ length: 1 2: ‘appendunittohostname’ length: 2 3: ‘password’ length: 0 4: ‘ssid’ length: 22 5: ‘key’ length: 10 6: ‘ssid2’ length: 0 7: ‘key2’ length: 0 8: ‘apkey’ length: 5 9: ‘ipblocklevel’ length: 1 10: ‘iprangelow’ length: 0 11: ‘iprangehigh’ length: 0 12: ‘espip’ length: 0 13: ‘espgateway’ length: 0 14: ‘espsubnet’ length: 0 15: ‘espdns’ length: 0 16: ‘awaketime’ length: 1 17: ‘delay’ length: 2 18: ‘plain’ length: 221
328797 : Info : SaveToFile: free stack: 3424
328867 : Info : FILE : Saved config.dat offset: 0 size: 1296
328869 : Info : SaveToFile: free stack after: 3424
328870 : Info : SaveToFile: free stack: 3264
328903 : Info : FILE : Saved security.dat offset: 0 size: 593
328904 : Info : SaveToFile: free stack after: 3264
328907 : Info : SaveToFile: free stack: 2928
328917 : Info : FILE : Saved security.dat offset: 1024 size: 128
328918 : Info : SaveToFile: free stack after: 2928
328920 : Debug : WiFi : Set TX power to 0dBm sensitivity: -69dBm
329092 : Info : WiFi : Best AP candidate: Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-60dBm) WPA2/PSK
329094 : Info : WIFI : Connecting Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-60dBm) WPA2/PSK attempt #0
329097 : Debug : WiFi : Set TX power to 11dBm sensitivity: -69dBm RSSI: -60dBm
329102 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: DISCONNECTED
329103 : Debug : WIFI : Disconnected: WiFi.status() = DISCONNECTED RSSI: 31 status: STATION_CONNECTING
scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 3
cnt
connected with Linksys Velop WHW03 V2, channel 10
dhcp client start…
330831 : Debug : WIFI : Entering processConnect()
330832 : Info : WIFI : Connected! AP: Linksys Velop WHW03 V2 (30:23:03:39:C4:5C) Ch: 10 Duration: 1734 ms
330833 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: Conn.
ip:10.187.1.143,mask:255.255.255.0,gw:10.187.1.254
332426 : Debug : WIFI : Entering processGotIP()
332428 : Info : WIFI : DHCP IP: 10.187.1.143 (ESP-Easy) GW: 10.187.1.254 SN: 255.255.255.0 duration: 1594 ms
332439 : Info : WIFI : Arduino wifi status: WL_CONNECTED 3 ESPeasy internal wifi status: Conn. IP
332440 : Debug : WiFi : WiFi services initialized
332562 : Debug More : NTP : NTP host ntp.xs4all.nl (194.109.6.2) queried
332605 : Info : NTP : NTP replied: delay 40 mSec Accuracy increased by 0.137 seconds
332607 : Info : Time set to 1623697489.137 Time adjusted by 38.45 msec. Wander: 0.01 msec/second
332610 : Info : Local time: 2021-06-14 19:04:49
333879 : Info : WD : Uptime 6 ConnectFailures 0 FreeMem 14032 WiFiStatus WL_CONNECTED 3 ESPeasy internal wifi status: Conn. IP Init
334768 : Debug : LoopStats: shortestLoop: 705 longestLoop: 5402515 avgLoopDuration: 5885.89 loopCounterMax: 42553 loopCounterLast: 5089
334769 : Debug : Scheduler stats: (called/tasks/max_length/idle%) 5085/1699/6/34.08
bcn_timout,ap_probe_send_start
ap_probe_send over, rest wifi status to disassoc
state: 5 -> 0 (1)
rm 0
341087 : Debug : WIFI : Entering processDisconnect()
341188 : Info : WIFI : Disconnected! Reason: ‘(200) Beacon timeout’ Connected for 10 s
341189 : Info : WIFI : Arduino wifi status: WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
341190 : Debug : WIFI : Disconnected: WiFi.status() = DISCONNECTED RSSI: 31 status: STATION_IDLE
349335 : Debug : HTML : Request file /index.htm.gz
349362 : Debug : HTML : Request file /index.htm
349488 : Info : Webserver args: 0: ‘cmd’ length: 6
349488 : Info : : Rebooting…
ets Jan 8 2013,rst cause:2, boot mode:(3,7)
load 0x4010f000, len 3584, room 16
tail 0
chksum 0xb0
csum 0xb0
v2843a5ac
~ld
ªU74 : Info :
INIT : Booting version: ‘bugfix/wifi_not_reconnect_56c4ca1’ (ESP82xx Core 2843a5ac, NONOS SDK 2.2.2-dev(38a443e), LWIP: 2.1.2 PUYA support)
76 : Info : INIT : Free RAM:32184
77 : Info : INIT : Soft Reboot #2 Last Action before Reboot: Intended Reboot: CommandReboot Last systime: 1623697506 - Restart Reason: Software/System restart
79 : Info : FS : Mounting…
104 : Info : FS : Mount successful, used 75802 bytes of 957314
153 : Info : FS : Success garbage collection
203 : Info : FS : Success garbage collection
269 : Info : FS : Success garbage collection
281 : Info : CRC : SecuritySettings CRC …OK
285 : Info : WiFi : Start network scan all channels
398 : Info : INIT : Free RAM:28112
399 : Info : INIT : I2C
400 : Info : INIT : SPI not enabled
499 : Info : INFO : Plugins: 47 [Normal] (ESP82xx Core 2843a5ac, NONOS SDK 2.2.2-dev(38a443e), LWIP: 2.1.2 PUYA support)
505 : Info : Webserver: start
506 : Info : Time set to 1623697506.000
508 : Info : Current Time Zone: STD time start: 2021-10-31 03:00:00 offset: 0 min
510 : Info : Local time: 2021-06-14 19:05:06
1851 : Info : WD : Uptime 0 ConnectFailures 0 FreeMem 21128 WiFiStatus WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
scandone
2550 : Info : WiFi : Scan finished, found: 5
2551 : Debug : WiFi : Scan result: #Hidden# 36:23:03:39:C3:A3 Ch:6 (-77dBm) WPA2/PSK
2552 : Debug : WiFi : Scan result: Broom 18:83:BF:BC:75:8A Ch:8 (-91dBm) WPA2/PSK
2553 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:13:49:8D Ch:1 (-69dBm) WPA2/PSK
2555 : Debug : WiFi : Scan result: Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-58dBm) WPA2/PSK
2556 : Debug : WiFi : Scan result: #Hidden# 36:23:03:13:49:8D Ch:1 (-69dBm) WPA2/PSK
2560 : Info : WiFi : Best AP candidate: Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-58dBm) WPA2/PSK
2562 : Info : WIFI : Connecting Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-58dBm) WPA2/PSK attempt #0
2565 : Debug : WiFi : Set TX power to 9dBm sensitivity: -69dBm RSSI: -58dBm
2568 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: DISCONNECTED
2570 : Debug : WIFI : Disconnected: WiFi.status() = DISCONNECTED RSSI: 31 status: STATION_CONNECTING
scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 3
cnt
connected with Linksys Velop WHW03 V2, channel 10
dhcp client start…
3659 : Debug : LoopStats: shortestLoop: 10335 longestLoop: 900285 avgLoopDuration: 16098.03 loopCounterMax: 2902 loopCounterLast: 193
3660 : Debug : Scheduler stats: (called/tasks/max_length/idle%) 191/135/6/16.21
3671 : Debug : WIFI : Entering processConnect()
3672 : Info : WIFI : Connected! AP: Linksys Velop WHW03 V2 (30:23:03:39:C4:5C) Ch: 10 Duration: 1092 ms
3673 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: Conn.
ip:10.187.1.143,mask:255.255.255.0,gw:10.187.1.254
5700 : Debug : WIFI : Entering processGotIP()
5701 : Info : WIFI : DHCP IP: 10.187.1.143 (ESP-Easy) GW: 10.187.1.254 SN: 255.255.255.0 duration: 2037 ms
5713 : Info : WIFI : Arduino wifi status: WL_CONNECTED 3 ESPeasy internal wifi status: Conn. IP
5714 : Debug : WiFi : WiFi services initialized
5716 : Info : firstLoopConnectionsEstablished
6303 : Debug More : NTP : NTP host ntp.xs4all.nl (194.109.6.2) queried
6326 : Info : NTP : NTP replied: delay 20 mSec Accuracy increased by 0.554 seconds
6327 : Info : Time set to 1623697512.554 Time adjusted by 770.75 msec. Wander: 0.21 msec/second
6330 : Info : Local time: 2021-06-14 19:05:12
bcn_timout,ap_probe_send_start
pm open,type:2 0
ap_probe_send over, rest wifi status to disassoc
state: 5 -> 0 (1)
rm 0
pm close 7
14132 : Debug : WIFI : Entering processDisconnect()
14233 : Info : WIFI : Disconnected! Reason: ‘(200) Beacon timeout’ Connected for 10 s
14234 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: DISCONNECTED
14235 : Debug : WIFI : Disconnected: WiFi.status() = DISCONNECTED RSSI: 31 status: STATION_CONNECTING
scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 3
cnt
connected with Linksys Velop WHW03 V2, channel 10
dhcp client start…
15097 : Debug : WIFI : Entering processConnect()
15099 : Info : WIFI : Connected! AP: Linksys Velop WHW03 V2 (30:23:03:39:C4:5C) Ch: 10 Duration: 12526 ms
15099 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: Conn.
15132 : Info : WIFI : Connecting Linksys Velop WHW03 V2 30:23:03:13:49:8D Ch:1 (-69dBm) WPA2/PSK attempt #1
15138 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: DISCONNECTED
15139 : Debug : WIFI : Disconnected: WiFi.status() = DISCONNECTED RSSI: -62 status: STATION_CONNECTING
scandone
state: 5 -> 2 (b0)
state: 5 -> 0 (2)
reconnect
17362 : Debug : WIFI : Entering processDisconnect()
17463 : Info : WIFI : Disconnected! Reason: ‘(204) Handshake timeout’ Connected for 2227 ms
17565 : Info : WIFI : Set WiFi to OFFscandone
del if0
usl
mode : null
force slp enable,type: 2
fpm open,type:2 0
17781 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: DISCONNECTED
17783 : Info : WiFi : Best AP candidate: Linksys Velop WHW0fpm close 3
3 V2 30:23:03:39:C4:5C Ch:10 (-58dBm) WPA2/PSK
17784 : Info : WIFI : Connecting Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-58dBmode : sta(f4:cf:a2:ed:b5:ed)
add if0
sleep enable,type: 2
m) WPA2/PSK attempt #2
17888 : Info : WIFI : Set WiFi to STA
17895 : Debug : WiFi : Set TX power to 0dBm sensitivity: -69dBm
17997 : Debug : WiFi : Set TX power to 9dBm sensitivity: -69dBm RSSI: -58dBm
18001 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: DISCONNECTED
18015 : Info : WIFI : Conscandone
necting Linksys Velop WHW03 V2 30:23:03:13:49:8D Ch:1 (-69dBm) WPA2/PSK attempt #3
18021 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: DISCONNECTED
scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 1
cnt
connected with Linksys Velop WHW03 V2, channel 1
dhcp client start…
19203 : Debug : WIFI : Entering processConnect()
19204 : Info : WIFI : Connected! AP: Linksys Velop WHW03 V2 (30:23:03:13:49:8D) Ch: 1 Duration: 1169 ms
19205 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: Conn.
ip:10.187.1.143,mask:255.255.255.0,gw:10.187.1.254
21050 : Debug : WIFI : Entering processGotIP()
21051 : Info : WIFI : DHCP IP: 10.187.1.143 (ESP-Easy) GW: 10.187.1.254 SN: 255.255.255.0 duration: 1858 ms
21063 : Info : WIFI : Arduino wifi status: WL_CONNECTED 3 ESPeasy internal wifi status: Conn. IP
21064 : Debug : WiFi : WiFi services initialized
21291 : Debug More : NTP : NTP host ntp.xs4all.nl (194.109.6.2) queried
21344 : Info : NTP : NTP replied: delay 51 mSec Accuracy increased by 0.581 seconds
21346 : Info : Time set to 1623697527.581 Time adjusted by 64.95 msec. Wander: 0.02 msec/second
21349 : Info : Local time: 2021-06-14 19:05:27
bcn_timout,ap_probe_send_start
pm open,type:2 0
ap_probe_send over, rest wifi status to disassoc
state: 5 -> 0 (1)
rm 0
pm close 7
29442 : Debug : WIFI : Entering processDisconnect()
29544 : Info : WIFI : Disconnected! Reason: ‘(200) Beacon timeout’ Connected for 10 s
29544 : Info : WIFI : Arduino wifi status: WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
29545 : Debug : WIFI : Disconnected: WiFi.status() = DISCONNECTED RSSI: 31 status: STATION_IDLE
30454 : Info : WiFi : Best AP candidate: Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-58dBm) WPA2/PSK
30455 : Info : WIFI : Connecting Linksys Velop WHW03 V2 30:23:03:39:C4:5C Ch:10 (-58dBm) WPA2/PSK attempt #4
30460 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: DISCONNECTED
30461 : Debug : WIFI : Disconnected: WiFi.status() = DISCONNECTED RSSI: 31 status: STATION_CONNECTING
scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 3
cnt
connected with Linksys Velop WHW03 V2, channel 10
dhcp client start…
31468 : Debug : WIFI : Entering processConnect()
31469 : Info : WIFI : Connected! AP: Linksys Velop WHW03 V2 (30:23:03:39:C4:5C) Ch: 10 Duration: 999 ms
31470 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: Conn.
31856 : Info : WD : Uptime 1 ConnectFailures 0 FreeMem 19744 WiFiStatus WL_DISCONNECTED 6 ESPeasy internal wifi status: Conn.
32749 : Debug : LoopStats: shortestLoop: 250 longestLoop: 905601 avgLoopDuration: 1261.38 loopCounterMax: 120000 loopCounterLast: 22925
32750 : Debug : Scheduler stats: (called/tasks/max_length/idle%) 22920/1697/6/59.32
ip:10.187.1.143,mask:255.255.255.0,gw:10.187.1.254
33039 : Debug : WIFI : Entering processGotIP()
33040 : Info : WIFI : DHCP IP: 10.187.1.143 (ESP-Easy) GW: 10.187.1.254 SN: 255.255.255.0 duration: 1576 ms
33052 : Info : WIFI : Arduino wifi status: WL_CONNECTED 3 ESPeasy internal wifi status: Conn. IP
33053 : Debug : WiFi : WiFi services initialized
33291 : Debug More : NTP : NTP host ntp.xs4all.nl (194.109.6.2) queried
33313 : Info : NTP : NTP replied: delay 20 mSec Accuracy increased by 0.543 seconds
33315 : Info : Time set to 1623697539.543 Time adjusted by 18.80 msec. Wander: 0.01 msec/second
33318 : Info : Local time: 2021-06-14 19:05:39
bcn_timout,ap_probe_send_start
pm open,type:2 0
ap_probe_send over, rest wifi status to disassoc
state: 5 -> 0 (1)
rm 0
pm close 7
41471 : Debug : WIFI : Entering processDisconnect()
41572 : Info : WIFI : Disconnected! Reason: ‘(200) Beacon timeout’ Connected for 10 s
41572 : Info : WIFI : Arduino wifi status: WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
41573 : Debug : WIFI : Disconnected: WiFi.status() = DISCONNECTED RSSI: 31 status: STATION_IDLE
42472 : Info : WIFI : Connecting Linksys Velop WHW03 V2 30:23:03:13:49:8D Ch:1 (-69dBm) WPA2/PSK attempt #5
42478 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: DISCONNECTED
42480 : Debug : WIFI : Disconnected: WiFi.status() = DISCONNECTED RSSI: 31 status: STATION_CONNECTING
scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 1
cnt
connected with Linksys Velop WHW03 V2, channel 1
dhcp client start…
43659 : Debug : WIFI : Entering processConnect()
43660 : Info : WIFI : Connected! AP: Linksys Velop WHW03 V2 (30:23:03:13:49:8D) Ch: 1 Duration: 1183 ms
43661 : Info : WIFI : Arduino wifi status: WL_DISCONNECTED 6 ESPeasy internal wifi status: Conn.
ip:10.187.1.143,mask:255.255.255.0,gw:10.187.1.254
45521 : Debug : WIFI : Entering processGotIP()
45523 : Info : WIFI : DHCP IP: 10.187.1.143 (ESP-Easy) GW: 10.187.1.254 SN: 255.255.255.0 duration: 1862 ms
45535 : Info : WIFI : Arduino wifi status: WL_CONNECTED 3 ESPeasy internal wifi status: Conn. IP
45536 : Debug : WiFi : WiFi services initialized
46291 : Debug More : NTP : NTP host ntp.xs4all.nl (194.109.6.2) queried
46344 : Info : NTP : NTP replied: delay 51 mSec Accuracy increased by 0.580 seconds
46346 : Info : Time set to 1623697552.580 Time adjusted by 62.19 msec. Wander: 0.02 msec/second
46349 : Info : Local time: 2021-06-14 19:05:52
Hope it helps to kill this bug...