Moderators: grovkillen, Stuntteam, TD-er
-
Barb232
- Normal user
- Posts: 40
- Joined: 12 Mar 2016, 16:40
- Location: Earth
-
Contact:
#1
Post
by Barb232 » 11 Apr 2018, 14:02
I have a problem to send the IP from the following example
Code: Select all
On System#Boot do //When the ESP boots, do
Publish %sysname%/co2Sensor/IP,%ip%
endon
On Rules#Timer=1 do //When Timer1 expires, do
Publish %sysname%/co2Sensor/IP,%ip%
timerSet,1,30 //Resets the Timer 1 for another 30 seconds
endon
Log
Code: Select all
4632 : EVENT: WiFi#ChangedAccesspoint
6338 : WIFI : DHCP IP: 192.168.178.52 (co2Sensor-18) GW: 192.168.178.1 SN: 255.255.255.0 duration: 1707 ms
6338 : EVENT: WiFi#Connected
6438 : MQTT : Intentional reconnect
6824 : MQTT : Connected to broker with client ID: ESPClient_B4:E6:2D:17:FB:AD
6832 : Subscribed to: /co2Sensor/#
6838 : EVENT: MQTT#Connected
15899 : MHZ19: Read error: checksum = 8 / 255 bytes read => 255/255/254/255/255/255/255/255/255/
15901 : MHZ19: Shifted 2 bytes to attempt to fix buffer alignment
31708 : WD : Uptime 1 ConnectFailures 0 FreeMem 16160
61875 : WD : Uptime 1 ConnectFailures 0 FreeMem 16160
76724 : MHZ19: Read error: checksum = 151 / 0 bytes read => 255/255/134/1/154/73/0/0/0/
76725 : MHZ19: Shifted 2 bytes to attempt to fix buffer alignment
91876 : WD : Uptime 2 ConnectFailures 0 FreeMem 16160
121876 : WD : Uptime 2 ConnectFailures 0 FreeMem 16160
136845 : MHZ19: PPM value: 588 Temp/S/U values: 33/0/0.00
136847 : EVENT: co2sensor#PPM=588.00
136856 : EVENT: co2sensor#Temperature=33.00
136863 : EVENT: co2sensor#U=0.00
151876 : WD : Uptime 3 ConnectFailures 0 FreeMem 16144
checkbox rules is enabled
using Release mega-20180410
/robin
-
wim16
- Normal user
- Posts: 88
- Joined: 01 May 2017, 20:35
#2
Post
by wim16 » 11 Apr 2018, 14:57
I notice 2 things in your rules, not sure if they cause the problem.
1. You do not set timer1 on boot so the second rule will never fire.
2. Maybe there must be a comma after ' publish' instead of the space.
-
Barb232
- Normal user
- Posts: 40
- Joined: 12 Mar 2016, 16:40
- Location: Earth
-
Contact:
#3
Post
by Barb232 » 11 Apr 2018, 15:43
i think there is a problem with rules
i did this
Code: Select all
On co2sensor#PPM >100 do
Gpio,16,1
Endif
and the log says
Code: Select all
6707 : MHZ19: PPM value: 410 Temp/S/U values: 32/0/0.00
76709 : EVENT: co2sensor#PPM=410.00
76720 : EVENT: co2sensor#PPM=410.00 Processing time:11 milliSeconds
76721 : EVENT: co2sensor#Temperature=32.00
76730 : EVENT: co2sensor#Temperature=32.00 Processing time:10 milliSeconds
76731 : EVENT: co2sensor#U=0.00
76740 : EVENT: co2sensor#U=0.00 Processing time:9 milliSeconds
76801 : MQTT : /co2Sensor/co2sensor/PPM 410.00
76808 : MQTT : /co2Sensor/co2sensor/Temperature 32.00
76812 : MQTT : /co2Sensor/co2sensor/U 0.00
76814 : MQTT : Topic: /co2Sensor/co2sensor/PPM
76814 : MQTT : Payload: 410.00
76820 : MQTT : Topic: /co2Sensor/co2sensor/Temperature
76820 : MQTT : Payload: 32.00
76821 : MQTT : Topic: /co2Sensor/co2se
so it never runs into the rules
yes, i checked the rules option button...
-
AndrewJ
- Normal user
- Posts: 229
- Joined: 14 Feb 2017, 12:38
#4
Post
by AndrewJ » 11 Apr 2018, 15:47
Barb232 wrote: ↑11 Apr 2018, 15:43
i think there is a problem with rules
i did this
Code: Select all
On co2sensor#PPM >100 do
Gpio,16,1
Endif
and the log says
snipped
so it never runs into the rules
yes, i checked the rules option button...
Hi, have a look at the Wiki on rules, it will guide you to the answer.
Post again if you are still stuck.
Good luck!
-
Barb232
- Normal user
- Posts: 40
- Joined: 12 Mar 2016, 16:40
- Location: Earth
-
Contact:
#5
Post
by Barb232 » 11 Apr 2018, 16:06
it works now
Code: Select all
339563 : EVENT: Rules#Timer=1
339574 : ACT : Publish co2Sensor/co2Sensor/IP,192.168.178.52
339639 : ACT : timerSet,1,30
Code: Select all
On System#Boot do //When the ESP boots, do
Publish %sysname%/co2Sensor/IP,%ip%
timerSet,1,30 //Set Timer 1 for the next event in 30 seconds
endon
On Rules#Timer=1 do //When Timer1 expires, do
Publish %sysname%/co2Sensor/IP,%ip%
timerSet,1,30 //Resets the Timer 1 for another 30 seconds
endon
Solution: I made a factory reset
Who is online
Users browsing this forum: Ahrefs [Bot] and 45 guests