ESPEASY Flasching and the first Wifi connection?

[ohaldi]

Hello,
I don't understand why, with ESPEASY, I always have problems obtaining a quick and simple first connection after flashing with ESPEASY Web.
Here's the link I used with Microsoft Edge. https://td-er.nl/ESPEasy/
After installation complete!, Logs & Console, Connect to Wifi, Configure Wi-Fi, Triyng to connect, nothing happend.

For example with Tasmota : https://tasmota.github.io/install/
I do not have this kind of problem.

Here some information from the console:
00:01:16.954 : (16288) Info : WD : Uptime 1 ConnectFailures 0 FreeMem 16424 WiFiStatus: WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
00:01:35.610 : (16368) Info : WiFi : Start network scan all channels
00:01:37.794 : (16136) Info : WiFi : Scan finished, found: 3
00:01:37.797 : (16256) Info : WIFI : Arduino wifi status: WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
00:01:46.951 : (16288) Info : WD : Uptime 2 ConnectFailures 0 FreeMem 16424 WiFiStatus: WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED

If I try with the help of Thermite:
00:01:16.947 : (16288) Info : WD : Uptime 1 ConnectFailures 0 FreeMem 16424 WiFiStatus: WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED
00:01:35.608 : (16368) Info : WiFi : Start network scan all channels
00:01:37.792 : (16056) Info : WiFi : Scan finished, found: 4
00:01:37.795 : (16256) Info : WIFI : Arduino wifi status: WL_IDLE_STATUS 0 ESPeasy internal wifi status: DISCONNECTED

If I set up the parameters :
wifissid,WIFINAME
wifikey,WIFIPASS
save
I get the OK answer.

But here, also I do not get a wifi connection. Only after a few power off / on, I can setup the wifi with the help of the AP mode.
Every time I load the ESPEASY firmware on an ESP32 or ESP8266, I have this kind of problem.
As I've already said with TASMOTA ESP Web Tools, it works the first time.
This is just for your information.
Regards
Otto

[TD-er]

That's exactly what I am working on right now. (as in literally now at this moment)
You can already try yesterday's build: https://td-er.nl/ESPEasy/latest/

Still a problem in that build when you disconnect wifi it might sometimes crash (working on) and switching WiFi off via command ("wifimode,off") from an external source (e.g. MQTT/webbrowser) may also cause a crash.

But at least it is now much faster in getting an IP right after scanning.

[ohaldi]

Thanks so much that you will fix this problem, you help is appreciated
ESPEasy is really a very good Firmware.
Small question : may I use this same file for one ESP8266 and ESP32?

I have a test board D1 WEMOS with one ESP-8266

[TD-er]

The platforms for which the same build type is available is listed in [...]
Thus if it states your platform in that list then you can select it to be flashed.

N.B. In about 10 minutes I will update the build in 'latest' to the new one I just made.
So you may need to refresh the page to see today's date appear in the list.

[TD-er]

Updated the build on https://td-er.nl/ESPEasy/latest/

N.B. I also updated to the latest flasher software, so it may take slightly longer to detect a board as it tries a bit harder to get the IMPROV string from the board stating any installed firmware.