Warema 8k hand transmitter

Post here about devices that are not yet or not fully supported

Moderators: rtenklooster, Voyager, BertB, Stuntteam

Post Reply
Message
Author
dproetel
New user
Posts: 6
Joined: 02 Feb 2017, 21:06

Warema 8k hand transmitter

#1 Post by dproetel » 02 Feb 2017, 21:13

good afternoon,
I try to connect a warema sender with 8 channels. Under device it shows:
rflinki 00006CA7 0 oben 6 Light/Switch Warema Open
but it seems that all 8 channels have the same entry. Any hints?

thanks in advance Daniel

User avatar
Stuntteam
Site Beheer
Posts: 791
Joined: 27 Jan 2016, 16:46

Re: Warema 8k hand transmitter

#2 Post by Stuntteam » 03 Feb 2017, 00:49

Check your email..
-=# RFLink Gateway Development Team #=-
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8

kafe75
New user
Posts: 1
Joined: 11 Feb 2017, 10:05

Re: Warema 8k hand transmitter

#3 Post by kafe75 » 11 Feb 2017, 10:12

good morning,

i´ve got the same problem with my 8k hand transmitter, controlling my roller shutters.

In domoticz the control command is recognized as warema protocol, but it´s always the same address.

Do i have to pair the devices with my master control unit?

User avatar
Stuntteam
Site Beheer
Posts: 791
Joined: 27 Jan 2016, 16:46

Re: Warema 8k hand transmitter

#4 Post by Stuntteam » 11 Feb 2017, 10:51

Check your email..
-=# RFLink Gateway Development Team #=-
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8

Des0re
New user
Posts: 1
Joined: 10 Aug 2019, 20:31

Re: Warema 8k hand transmitter

#5 Post by Des0re » 21 Aug 2019, 18:07

I also have a problem with warema EWFS
Rflink recognises the switches. But i cannot control with rflink.

tkospace
New user
Posts: 1
Joined: 09 Jun 2020, 23:26

Re: Warema 8k hand transmitter

#6 Post by tkospace » 09 Jun 2020, 23:28

Stuntteam wrote: 11 Feb 2017, 10:51 Check your email..
Hello,

I have the same problem.
Could you send me the information too?

Br,
tkospace

intelligenzbestie
New user
Posts: 1
Joined: 23 Jun 2020, 21:08

Re: Warema 8k hand transmitter

#7 Post by intelligenzbestie » 23 Jun 2020, 21:16

Hello,

I would be interested as well.
I have a Warema EWFS Weather Station Plus combined with an adapter to control an even older Warema awning.
I also have a handheld transmitter to manually move it out and in.
I managed to retrieve the commands for out and in using a Signalduino at 433 MHz and I can "replicate" them as raw messages so this works.
But I would be intested in the data of the weather station because it contains a wind and rain sensor.
And I would like to "see" when the weather station "commands" the awning to move out or in.

Thanks,
best regards
Richard

User avatar
Stuntteam
Site Beheer
Posts: 791
Joined: 27 Jan 2016, 16:46

Re: Warema 8k hand transmitter

#8 Post by Stuntteam » 24 Jun 2020, 00:05

For new/unknown devices follow the instructions here: http://www.rflink.nl/blog2/development
-=# RFLink Gateway Development Team #=-
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8

Tom_77
New user
Posts: 1
Joined: 29 May 2024, 18:39

Re: Warema 8k hand transmitter

#9 Post by Tom_77 » 29 May 2024, 18:56

Is there a special thing with the Warema EWFS 8K Controller?

I try to control my Warema venetian blinds with RFLink but no Command works.

I use a Nodo RFLink Gatewayboard (RLink Firmware Version: 1.1 Revision: 51) and have a Warema EWFS 8K Controller.
For example, when pushing a Button of the Controller, I receive in the RFLink Loader (V1.11) screen:
20;68;Warema;ID=ae16;SWITCH=01;CMD=DOWN;

I now try to send in the "Command to Send"-Field in RFLink Loader the following:
10;Warema;ae16;1;DOWN;

Receiving the following:
20;88;OK;

But the Warema venetian blinds are not moving?

tuxinger
New user
Posts: 2
Joined: 23 Jul 2024, 08:02

Re: Warema 8k hand transmitter

#10 Post by tuxinger » 23 Jul 2024, 08:07

Same here, got a RFLink from nodoshop. I can see the commands transmitted by the remote, but if I send, nothing happens.
Can anyone please post a brief description how to use RFlink with warema ewfs. I think we are missing the side-channel learning, but as the code is not Opensource and no docs given I have no clue how to do it.

tuxinger
New user
Posts: 2
Joined: 23 Jul 2024, 08:02

Re: Warema 8k hand transmitter

#11 Post by tuxinger » 26 Jul 2024, 22:18

As nobody replies, neither to this post not to te e-mail I've written to the contact email of the rflink. I consider this projekt as abadoned and dead. This is a little disapointing as the hardware still gets sold, and the code is not available. Perhaps we should consider an os firmware for the Hardware.

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest