Let's Control It

Hi,

i take V101 on an resetted ESP-01 and tested the autoconfig:

see ESP_0 on my iPhone

login to these AP

set the WLAN Parameters,

see in the serial line, he´s logging in

get an IP via DHCP (another IP Range, outside the old one)

INIT : Boot OK
INIT : Normal boot
>settings

System Info
IP Address : 0.0.0.0
Build : 101
Unit : 0
WifiSSID : ssid
WifiKey : wpakey
Free mem : 26072

Ok
WD : Uptime 0 ConnectFailures 0 FreeMem 26200
add 1
aid 1
station: 90:b9:31:09:3c:87 join, AID = 1
WD : Uptime 1 ConnectFailures 0 FreeMem 25056
scandone
WD : Uptime 1 ConnectFailures 0 FreeMem 24256
WIFI : Connecting... 1
scandone
state: 0 -> 2 (b0)
station: 90:b9:31:09:3c:87 leave, AID = 1
rm 1
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 2
cnt

connected with xxxxxx, channel 2
dhcp client start...
ip:192.168.113.239,mask:255.255.255.0,gw:192.168.113.1
WIFI : Connected!

after that i did´nt can´t access this site, there´s an redirect to:

!!!!!!!

192.168.4.1/setup

and this is outside the possible range.

settings

System Info
IP Address : 192.168.113.239
Build : 101
Unit : 0
WifiSSID : xxxxxx
WifiKey : xxxxxxxxxxxxxxxxx
Free mem : 24136

Ok

I did´nt see any "FLASH: Settings saved" on the serial line.


a week ago i wrote a bug report regarding ESP-12F, see

http://www.esp8266.nu/forum/viewtopic.php?f=6&t=1368

it looks like the same problem.

PS:

found a workaround until these problem is solved:
call:

http://IP/config

this is running fine
click on the "submit" Button
u can see in the serial line:

FLASH: Settings saved
FLASH: Settings saved

what is NOT Running:
after that change to "Tools" and press the reboot button.

This runs:
Press the resetbutton on the hardware
or repower it.

AFTER this INIT u can use your ESPeasy on the normal way

same problem! tested both R100 and R101

yes, same problem!

The initial Wifi setup should take you to the config page as the last step, there you should submit the main config settings and they should be saved to flash.
As described here on the Wiki page: http://www.esp8266.nu/index.php/EasySetup

Did you reconnect the iPhone to your primary AP during the process, before clicking "Proceed to main config" ?

Martinus wrote:.... before clicking "Proceed to main config" ?

Hi Martinus,

i´d never see this point.

In the first step i give him the WLAN Parameters and click connect.
2nd my iPhone looses the ESP_0 AP and connect into my WLAN, automaticcally, no chance to change this.

the following redirect is wrong, but only when u ask without suffix: 192.168.4.1 because the new DHCP Address is there ignored.

clicking "Proceed to main config"......., never seen.

So, just testet again:
iphone looses ESP_0 AP

taked a look with my wifi card on the PC, oh !! it´s exist´s!
connect and taked a look into 192.168.4.1

there are your site, nice,

clicked on "Proceed to main config" and seen in the serial line: nothing happens
but i´m in the config tab in the browser, click on submit and now the settings are saved!

So we had a problem on the way